Axxess ASWC-1 Manual de usuario

METRA. THE WORLD’S BEST KITS.®

1-800-221-0932 metraonline.com

REV. 10/12/2017 ASWC-INST10

INSTALLATION INSTRUCTIONS ASWC-1

INTERFACE FEATURES

• One Interface does it all - No additional interfaces needed

• Designed to be compatible with all major radio brands

• Auto detects vehicle type, radio connection, and presets controls

• Ability to dual assign steering wheel control buttons

• Can be manually programmed for most vehicles

• Memory retains settings even after battery disconnection

or interface removal

• All connections done at the radio location

• Micro “B” USB updatable

INTERFACE COMPONENTS

• ASWC-1 Interface • 12-pin harness with male 3.5mm connector

• Female 3.5mm connector with Brown and Brown/White wires

TOOLS REQUIRED

• Cutting tool • Crimping tool • Tape

Axxess Steering Wheel Control

Interface Installation Manual

ASWC-1

US. PAT. NOS. 8014920 and 8214105

Table of Contents

Preface .............................................................................................. 3

Overview

– Introduction to the ASWC-1 Interface and Wiring Harness ..............4-5

ASWC-1 Installation

– Connections to be Made ................................................................6-7

– Programming.................................................................................8-9

Auto Detect Mode: Overview........................................................ 8

Auto Detect Mode: Steps ..........................................................8-9

– Remapping the SWC (steering wheel control) Buttons................10-11

Button Assignment Legend........................................................ 11

– Changing Radio Type .................................................................12-13

Radio Legend ............................................................................ 13

– Dual Assignment Instructions.....................................................14-15

Dual Assignment Legend ........................................................... 15

ASWC-1 Troubleshooting

– Auto Detect Mode......................................................................16-18

– Manual Programming Mode.......................................................19-21

Manual Programming Legend.................................................... 21

– Resetting Original ASWC-1 Settings................................................ 22

– LED Feedback............................................................................22-23

Caution: Metra recommends disconnecting the negative battery terminal

before beginning any installation. All accessories, switches, and especially

air bag indicator lights must be plugged in before reconnecting the battery or

cycling the ignition.

What you need to know before you begin

1) Know the correct year, make, and model of your vehicle.

2) Ensure the steering wheel controls work before removing the factory

radio, and know what the Volume Up button is. The Volume Up

button is used for programming, so knowing this before removing

the radio is crucial.

Note: Steering wheel controls must be the ones that came with the

vehicle when purchased. We do not support custom work, i.e. adding

a new steering wheel with added/new buttons.

3) Go to the Axxess website (axxessinterfaces.com) and click on the

link entitled “ASWC-1 Vehicle Instructions”, which is located on the

right side of the screen in the middle. Once you put your vehicle

information in, click the “Submit” button. This will take you to

another page, where you will then click on the link under the word

“Documents”. This will provide the vehicle specific instructions

for your vehicle. Print this document so you have it with you in the

vehicle during the install as it is the best, and most recent

source of information.

4) Be sure that the radio you are installing is compatible with the

ASWC-1. Additionally, refer to the Radio Legend (p. 13) and your

radio’s owners manual.

5) Update the ASWC-1 to the latest software. Note: To update go to

axxessinterfaces.com and download the WebXXpress program.

Attention: Even though we have done extensive research and testing

to verify that the steering wheel control wires we list are correct. It is

your responsibility to verify the steering wheel control wires we list are

correct with a multimeter. If you find an error, please notify our Axxess

Tech department at 1-800-253-TECH. Please be in the vehicle, parked,

along with access to the interface and vehicle wiring when you call.

Preface

Introduction to the ASWC-1 Interface

and Wiring Harness

On the top of the ASWC-1 interface there are three points of interest:

1) Programming LED

2) Reset Button

3) Update Port Cover (slide to open)

Overview

Update Port Cover Reset Button* Programming LED

*Note: The Reset button is recessed.

An item, such as a partially unfolded paper

clip, is needed to press the button.

Micro “B”

USB

Overview

Shown below: Female 3.5mm

connector with Brown (Br) and

Brown/White (Br/W) wires.

Br/W

Shown above: 12-pin harness with

male 3.5mm connector.

Pin-1 Pink

Pin-2 White/Green

Pin-3 Yellow/Green

Pin-4 Green/Orange

Pin-5 Gray/Red

Pin-6 Black

Pin-7 Blue/Pink

Pin-8 Black/Green

Pin-9 Red (tip of 3.5mm connector)

Pin-10 White (ring of 3.5mm connector)

Pin-11 Gray/Blue

Pin-12 Red

Below are the wire colors for the ASWC-1. Please visit the

Axxess website at www.axxessinterfaces.com for detailed information

on your specific vehicle and for what color wire(s) to use with the

ASWC-1 interface.

ASWC-1 Installation

Connections to be made

Once you have collected or printed out the “ASWC-1 Vehicle Instructions”

for your particular vehicle, from www.axxessinterfaces.com, you’re ready

to install the ASWC-1.

Note: If wiring is not available on our website for your vehicle, you will

need to obtain this yourself. Please check first with Axxess Tech Support

department at 1-800-253-TECH, as we may have this information.

Into vehicle:

1) Connect the Black wire of the ASWC-1 to the ground. You may use

the same grounding point as the aftermarket radio; but

it is highly recommended to ground the ASWC-1 to the chassis,

of the vehicle, by itself.

2) With the key in the off position, connect the Red wire of the ASWC-1

to the 12-volt accessory wire.

3) Locate the correct steering wheel control wire(s) in the vehicle’s

harness, as described in the “ASWC-1 Vehicle Instructions”. Connect

these wires to the ASWC-1.

Note: Metra recommends that the wires are soldered for

the best and most secure connection. Tapping style connectors

are not recommended due to a higher chance of a intermittent

connection or change in resistance values (which will cause the

ASWC-1 to fail to program).

Into radio:

1) For the radios listed below, plug the included female 3.5mm adapter

(with the Brown and Brown/White wires) into the male 3.5mm

connector of the ASWC-1 harness.

A. For Eclipse radios: Connect the Eclipse steering wheel control

wires (normally Brown and Brown/Black) to the Brown and

Brown/White wires of the ASWC-1. The Brown of the ASWC-1

goes to the Brown/Black of the Eclipse and Brown/White of the

ASWC-1 goes to the Brown of the Eclipse.

ASWC-1 Installation

Connections to be made

B. For Metra OE radios: Connect the steering wheel control

Key 1 wire (Gray) to the Brown wire of the ASWC-1. Isolate and

tape the Brown/White wire, it will not be used.

C. For Kenwood, or select JVC’s with a Blue/Yellow steering

wheel control wire: Connect the Kenwood/JVC steering wheel

control wire to the Brown wire of the ASWC-1. Isolate and tape

the Brown/White wire, it will not be used.

Note: Some of the newer Kenwood radios will auto detect as a

JVC. If this is the case, manually set the radio type, refer to the

Changing Radio Type section (pp. 12-13).

D. For XITE radios: Connect the steering wheel control SWC-2 wire

from the radio to the Brown wire of the ASWC-1. Isolate and tape

the Brown/White wire, it will not be used.

2) For Parrot Asteroid Smart or Tablets: Connect the 3.5mm jack of

the ASWC-1 into the female 3.5mm jack of the AX-SWC-PARROT

(sold separately). Then plug the 4-pin male harness into the

corresponding steering wheel control female harness in the radio.

Note: AX-SWC-PARROT is required (sold separately) and the radio

must be updated to rev. 2.1.4 or higher. Additionally, the ASWC-1

must be updated to the most recent software available.

3) For all other radios: Plug in the male 3.5mm connector of the

ASWC-1 into the back of the aftermarket radio, designated for

an external steering wheel control interface. Please refer to the

aftermarket radios manual if in doubt where the 3.5mm connector

of the ASWC-1 goes into.

The ASWC-1 can be programmed two different ways. It can auto

program itself through Auto Detect Mode, or it can be manually

programmed (pp. 19-21). The following, which is recommended, is for

auto programming.

Auto Detect Mode: Overview

The ASWC-1 has the ability to auto detect select vehicles and what

aftermarket radio it is connected to. The “ASWC-1 Vehicle Instructions”,

found at www.axxessinterfaces.com, will indicate if your vehicle will auto

detect and what action, if any, is required for this process to take place.

For the auto detect feature to work there are (3) possible actions that must

be taken. Note, only one action will be required depending on the vehicle:

1. Turn the ignition on and no other action is required.

--- Or ---

2. Turn the ignition on, press and hold the Volume Up button on the

steering wheel.

--- Or ---

3. Turn the ignition on, and then tap the Volume Up button repeatedly

on the steering wheel.

Auto Detect Mode: Steps

Note: Please read all Auto Detect Mode steps before beginning.

1) Complete connections to the vehicle and the aftermarket radio.

Turn the ignition on, the LED will start rapidly flashing Red; which

means the ASWC-1 is looking for the vehicle and the radio.

Note: If the LED did not start flashing Red rapidly press the reset

button for 3 seconds and then proceed to Step 3.

3) Perform action required for your particular vehicle, as noted in the

“ASWC-1 Vehicle Instructions”, download from Axxessinterfaces.com.

ASWC-1 Installation

Programming

4) After a few seconds the LED should stop flashing rapidly and go out

for approximately 2 seconds. At this point do not press any buttons.

5) After the approximate 2 seconds there will be a series of 7 Green

flashes, some short, and some long. The long flashes represent the

wires that

are re

cognized by the ASWC-1.

Tip: Knowing this will help if you need to troubleshoot; refer to p. 22,

for the appropriate LED Feedback section legend.

6) The LED will pause for another 2 seconds, and then flash Red up to

15 times d

epend

ing on what radio is connected to the ASWC-1.

Tip: Knowing this will help if you need to troubleshoot; refer to p. 23,

for the appropriate LED Feedback section legend.

7) This is the end of the auto detection stage. If the ASWC-1 detected

the vehicle and the radio successfully the LED will light up solid.

8) For vehicles with OE Bluetooth buttons, press and hold the

Hang up or Pick up button on the steering wheel after the LED on

the ASWC-1 goes solid. If the OE Bluetooth buttons are able to be

used the LED will go out after 3 seconds. Your OE Bluetooth buttons

are now programmed to your afterm

arket ra

dio.

Note: The aftermarket radio must have Bluetooth capability and must

be able to accept these commands.

9) Make sure the steering wheel control buttons function correctly in the

vehicle and enjoy.

Tip: If the ASWC-1 did not go to a solid LED, press the Reset button

for 3 seconds, release, and then start from Step 3. If the LED still doesn’t

go to a solid LED refer to the LED Feedback section (p. 22).This will help

you to determine if the ASWC-1 is detecting your vehicle. If not, refer to

the instructions starting on p. 6, and make sure all the instructions were

followed as stated. If you have done this and the ASWC-1 is still not going

to a solid LED please refer to the Troubleshooting section (pp. 16-18).

ASWC-1 Installation

Programming

Let’s say you have ASWC-1 programmed to your radio and you want

to change the button assignment for the steering wheel controls. For

instance, you would like Seek Up to be Mute. Follow the steps below to

remap the steering wheel control buttons:

1) Make sure the ASWC-1 is visible, so you can see the LED flashes to

confirm button recognition.

Tip: Turning off the radio is recommended.

2) Within the first 20 seconds of turning the ignition on,

press and hold the Volume Up button on the steering wheel until the

LED goes solid.

3) Release the Volume Up button and the LED will go out; Volume Up

has now been programmed.

4) Follow the list in the Button Assignment Legend (p. 11),

to reference the order in which the steering wheel control buttons

need to be programmed.

Note: If the next function on the list is not on the steering wheel;

press the Volume Up button for 1 second, until the LED comes

on, and then release the button. This will tell the ASWC-1 that the

function is not available and it will move onto the next function.

5) To complete the remapping process, press and hold the Volume Up

button on the steering wheel until the LED on the ASWC-1 goes out.

ASWC-1 Installation

Remapping the SWC buttons

Otros manuales para ASWC-1

Tabla de contenidos

Idiomas:

Otros manuales de Equipo de grabación de Axxess

Axxess

Axxess AXDSPX-BM1 Manual de usuario

Axxess

Axxess GMOS-04 Manual de usuario

Axxess

Axxess AXDSPL-BM1 Manual de usuario

Axxess

Axxess GMOS-LAN-10 Manual de usuario

Axxess

Axxess LC-CHRC-01 Manual de usuario

Axxess

Axxess GMOS-05 Manual de usuario

Axxess

Axxess AX-CH013-SWC Manual de usuario

Axxess

Axxess AX-FD1-SWC Manual de usuario

Axxess

Axxess AX-DSP-A2B1 Manual de usuario

Axxess

Axxess AX-FD-SSO Manual de usuario

Axxess

Axxess AXDSPL-GM31 Manual de usuario

Axxess

Axxess ADBX Series Manual de usuario

Axxess

Axxess MITO-03 Manual de usuario

Axxess

Axxess GMOS-05 Guía del usuario

Axxess

Axxess GMOS-LAN-03 Manual de usuario

Axxess

Axxess AX-DSPX-WR Manual de usuario

Axxess

Axxess GMOS-08 Manual de usuario

Axxess

Axxess AXTC-FD2 Manual de usuario

Axxess

Axxess AX-ADBOX1 series Manual de usuario

Axxess

Axxess AXTC-VW1 Manual de usuario

Axxess

Axxess XSVI-2004 Manual de usuario

Axxess

Axxess AX-AM-AU96 Manual de usuario

Axxess

Axxess CHTO-02 Manual de usuario

Axxess

Axxess AX-BM90122 Manual de usuario

Manuales populares de Equipo de grabación de otras marcas

KV2 Audio

KV2 Audio 500 Series Manual de usuario

Robotics Technologies

Robotics Technologies microBus-Cam II Manual de usuario

Seca

Seca 460 Manual de usuario

Cognex

Cognex MVS-8000 Series Manual de usuario

Mect

Mect MPNC006 Series Manual de usuario

Bad Caf

Bad Caf THE LEASH Manual de usuario

Strymon

Strymon NIGHTSKY Manual de usuario

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manual de usuario

Tews Technologies

Tews Technologies TPMC465 Manual de usuario

Honeywell

Honeywell Excel 50 Manual de usuario

SeaLevel

SeaLevel COMM+8.LPCI Manual de usuario

Arturia

Arturia AUDIOFUSE STUDIO Manual de usuario

Rukra

Rukra RK-1240 Manual de usuario

Samson

Samson SCOM Manual de usuario

Dynacord

Dynacord DPS260 Manual de usuario

Nice

Nice Core Manual de usuario

Pyle Pro

Pyle Pro PSS8 Manual de usuario

RF-System

RF-System TinyGate Manual de uso y cuidado