Axminster 100714 Manual de usuario

Axminster

Single Hinge Jig

Code 100714

(Clamp not supplied)

Index of Contents

Page

Index of Contents 2

Introduction 3

What’s in the Box 3

General Instructions for Working Practice/Safety 3

Initial Assembly Instructions 3

Using the Template 4-5-6

Guide Bush and Cutter Chart 7

Warning The symbols below advise that you follow

the correct safety procedures when using

this machine.

Fully read manual

and safety instructions

before use

Eye protection

should be worn

Ear protection

should be worn

Dust mask

should be worn

This product has been wholly designed and manufactured by Axminster Tool Centre Ltd who have exclusive use of the

design and manufacture. As such it should not be copied or reproduced.

Introduction

Axminster Single Hinge Jig

The Axminster Single Hinge Jig is designed to cut hinge recesses in combination with any size router ﬁtted

with an appropriate guide bush. Using the suggested 26mm guide bush and 20mm cutter, the template will

cut recesses for 100mm and 50mm butt hinges. Using alternative cutter and guide bush combinations, it can

also be used to cut recesses for other size butt hinges and for 35 and 26mm circular boss style cabinet hinges.

The jig can be used for cutting the hinge recess into the edge of a door as well as into a door frame or carcase.

Quantity Item Code

100714

1 No. Clear plastic template

1 No. Box section aluminium stock

2 No. Countersunk hex bolts

2 No. Star knobs

1 No. Manual

What’s Included

General Instructions for Working Practise/Safety

Carefully read and follow the router manufacturer’s instruction book

to ensure that you are competent in handling and using the router.

Follow all safety procedures and regulations in respect of the use of

electric power tools.

Always wear suitable eye and ear protection as well as protection against dust

inhalation when using the router.

WARNING! DO NOT OVERTIGHTEN AS THIS COULD DAMAGE THE TEMPLATE

(Note: clamp is not supplied with the kit)

Initial Assembly Instructions

Attach the template to the stock using the two countersunk bolts, inserted through the countersunk slots in

the template face. Secure with the two star knobs.

Using the Template

Using the template to cut 100mm

hinge recesses in the door edge

1. The template is ﬁrst adjusted to position the hinge

knuckle or pivot pin on the door edge to ensure that

the door will close correctly to the doorframe.The

inside edge of the template is set to the width of

the hinge ﬂap plus the guide bush margin. (See ﬁg

01)The guide bush margin is simply the difference

between the cutter diameter and the outside guide

bush diameter, divided by two. Using the suggested

26mm guide bush and a 20mm cutter, the margin will

be 3mm. As the template opening is 106mm, using

this combination will leave a recess length of 100mm

or the length of the hinge. Imperial 4inch long hinges

will require a 25mm guide bush and the 20mm cutter.

2. Mark out the centre line of the hinge positions on

the door edge. (See ﬁg 02) Clamp the box section of

the jig, with the open edge of the template on the

hanging (i.e. pivot edge) face of the door. (See ﬁg 03)

Align the engraved centre line on the template with

the hinge centre line marked on the door edge.

Check that the template edge is square to the door

face before tightening the locking knobs. Do not

over tighten as this may damage the template.

NOTE.This formula can be used to calculate any

recess length to accommodate variations in the

hinge length. For example a 75mm hinge recess

cut using the 106mm template will require a

guide bush diameter of 40mm and a cutter

diameter of 9mm. 106 - 75 = 31. Using a 40mm

guide bush = 40 - 31 = 9mm diameter cutter.

Fig 01

Fig 02

Template Hinge

Marking out the centre line of the hinge positions on

the door edge

Fig 03

Clamping the box section of the jig

3. Fit the correct diameter guide bush and cutter to

the router to achieve the length of recess to suit the

hinge. (See ﬁg 04) As the template thickness is 6mm,

the guide bush depth beneath the router base must

be slightly less than this.

Centre line

Using the Template

Fig 07-08

4. When setting the recess depth (i.e. cutter depth), sit

the router ﬂat on the template face and bottom the

cutter on to the door edge.(See ﬁg 05) Set the depth

stop using the ﬂap of the hinge inserted between

the turret stop screw and the depth gauge rod. It is

always advisable to initially cut the recess in a piece

of scrap timber and check the ﬁnished recess depth.

Fig 04

Guide bush and cutter

Fig 05-06

Setting the recess for the cutter depth

Cutting the door hinge by starting

from the door edge

The door edge

Door hinge recess

Bevel edge chisel

Corner chisel

5. Cut the recess by ﬁrst locking the router plunge

to the depth set by the depth gauge and cutting

in from the edge of the door. (See ﬁg 06) Start by

making a back cut (i.e. against the direction of cutter

rotation, that is from right to left), before removing

the remaining waste from the recess. By back cutting

you will achieve a clean recess edge. If the recess is

slightly short, remove a sliver from one end using a

sharp bevel edge chisel.

6. To ﬁnish, square the corners of the recess using a

corner chisel (code 340437) or a sharp bevel edge

chisel. (See ﬁgs 07-08)

Using the Template

7. Matching recesses can be cut into doorframes or

linings using the hinge jig.The jig can be clamped

to the frame prior to the architraves being ﬁtted or

to a lining prior to the architraves and planted stop

being ﬁtted. (See ﬁg 09) Countersunk screw holes are

provided on the template to provide extra support if

necessary, or for use when a clamp cannot be ﬁtted.

To provide extra support when recessing a frame

with a machined stop, attach a small block of wood,

the same depth as the stop, to the underside of the

template with double-sided tape.

To cut the recess, align the template against a hinge

centre line drawn on the frame or lining and cut and

ﬁnish as for the door edge.(See ﬁg 10)

Fig 09

The jig being clamped to the frame prior to the

architraves being ﬁtted or to a lining prior to the

architraves and planted stop being ﬁtted

Fig 10

To cut the recess, align the template against a hinge

centre line drawn on the frame or lining and cut

and ﬁnish as for the door edge

8. When cutting a number of doors with similar hinge

positions, two or more templates can be used, ﬁtted

to a 24mm by 24mm timber batten and spaced out

accordingly.

Concealed cabinet hinges

9. The hinge template can also be used to bore

circular holes to accept the boss of a concealed

cabinet hinge, the standard diameter hinge bosses

being 35 and 26mm. Again using various guide bush

and cutter diameters will accommodate different

hinge boss diameters.The template hole is 48mm

diameter, therefore a combination of a 24mm guide

bush and a 12mm cutter and a 30mm guide bush

and 9mm cutter will produce recesses of 35 and

26mm diameter respectively.

In use, simply set the box section on the template

to position the hinge in from the edge of the door.

Mark the centre line of the hinge from either top or

bottom door edges. Align the template centre line

and clamp the template securely. (See ﬁg 11) Set the

cutter depth to the depth of the hinge boss (normally

10mm) plus the thickness of the template.

Fig 11

Fig 12

Template hole

Cabinet hinge

Guide Bush & Cutter Chart

Hinge Length

Guide Bush

Diameter Cutter Diameter Template

100mm 26mm 20mm 106mm Template

75mm 40mm 9mm 106mm Template

50mm 26mm 20mm 56mm Template

25mm 40mm 9mm 56mm Template

35mm Diameter 24mm 12mm 48mm Dia Template

26mm Diameter 30mm 9mm 48mm Dia Template

Axminster Tools & Machinery Ltd,

Weycroft Avenue, Axminster, Devon EX13 5PH

axminster.co.uk

Please dispose of packaging for the product in a responsible manner. It is suitable for recycling.

Help to protect the environment, take the packaging to the local recycling centre and place into

the appropriate recycling bin.

Do not dispose of electric tools together with household waste material. In observance of

European Directive 2002/96/EC on waste electrical and electronic equipment and its

implementation in accordance with national law, electric tools that have reached the end of their

life must be collected separately and returned to an environmentally compatible recycling facility.

Only for EU countries

Tabla de contenidos

Otros manuales de Herramientas de Axminster

Axminster

Axminster PROFESSIONAL 103738 Manual de usuario

Axminster

Axminster Pen Kit Manual de usuario

Axminster

Axminster Woodturning Deluxe Pen Press Manual de usuario

Axminster

Axminster SIEG Super X2 Mill Manual de usuario

Axminster

Axminster RTC7030 Manual de usuario

Axminster

Axminster Collet Chuck System Set Manual de usuario

Axminster

Axminster Empress Pen Kits Manual de usuario

Axminster

Axminster Super Precision Woodturning Chuck Manual de usuario

Axminster

Axminster AW19FM Manual de usuario

Axminster

Axminster SIEG X1 Super Micro Mill Mk2 Manual de usuario

Axminster

Axminster Woodturner's Clubman & Goliath Chucks Manual de usuario

Axminster

Axminster CSC500C Manual de usuario

Axminster

Axminster Universal Sub Base Manual de usuario

Axminster

Axminster CrushGrind Shaft 195mm Manual de usuario

Axminster

Axminster Router Elevator Manual de usuario

Axminster

Axminster PROFESSIONAL AP50UE Manual de usuario

Axminster

Axminster Trade Series Manual de usuario

Axminster

Axminster 504633 Manual de usuario

Axminster

Axminster AW19FM Manual de usuario

Axminster

Axminster UJK Cabinet & Recess Hinge Jig Manual de usuario

Axminster

Axminster WS1000TA Manual de usuario

Axminster

Axminster CSC500K Manual de usuario

Axminster

Axminster ujk 106843 Manual de usuario

Axminster

Axminster Digital Height Gauge Manual de usuario

Manuales populares de Herramientas de otras marcas

Martor

Martor SECUNORM 175 Manual de usuario

ERKCO

ERKCO 1000 Manual de usuario

jbc

jbc N4473 Manual de usuario

FEINMETALL

FEINMETALL FZWZ-SET-001 Manual de usuario

Worx Professional

Worx Professional Sonicrafter WU676 Manual de usuario

Gage Bilt

Gage Bilt GB713SH Manual de usuario

Hilti

Hilti DX 9-ENP Manual de usuario

norbar

norbar NORTRONIC 34399 Manual de usuario

BGS technic

BGS technic 8578 Manual de usuario

Makita

Makita DHR241 Manual de usuario

Motor Guard

Motor Guard JMB-1250 Manual de usuario

Power Adhesives

Power Adhesives 805-12 Manual de usuario

Clemco

Clemco 24189 Manual de usuario

VVG

VVG VNG 903 Series Manual de usuario

Hilti

Hilti FX 3-A Manual de usuario

Grizzly

Grizzly H6472 Manual de usuario

axing

axing BWZ 5-02 Manual de usuario

Dh-Robotics

Dh-Robotics RGI-100 Cómo utilizar