AWNLUX W5700 Manual de usuario
W20180130EN
Package Components..................................................3
Preparation...................................................................5
Installation....................................................................6
Motor limit position adjustment...................................11
Operation.…………………………………………….....12
Maintenance....……………………………………........15
CONTENTS
Please read and insure you understood this
instruction before install, adjust, service and
maintain the awnings. This awning must be
installed and serviced by qualified person.
Please be sure to take good care of this ma-
nual for daily maintenance !
WARNING
Package Components
W5700
DESCIPTION
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
Fabric lock rail
Fabric tube
Left arm
Right arm
M5x40 Hex head screws
M6x60 Hex head screws
M6x50 Screw
Ø4.2x13.5 Self-tapping screw
M6X16 Screw
Hand crank
belt
Switch
Adjustable rod
9
10
12
11
13
3
Package Components
W5700C
DESCIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Fabric lock rail
Fabric tube
Left arm
Right arm
M5x40 Hex head screws
M6x50 Screw
M6x60 Hex head screws
Ø4.2x13.5 Self-tapping screw
M6X16 Screw
Hand crank
belt
Switch
Fabric tube connector
Adjustable rod
ITEM
12
11
13
10
14
4
Preparation
Metric size
Measurement position sheet Unit : m
Total Width (Upper)
Awning Width (A)
Fabric lock Width
Fabric Width
Total Width (Bottom)
Folded arm Height
Extension (Max.)
A+0.085
A-0.13
A-0.25
A+0.06
1.96
2.5
2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
Note: The 6 mounting points must be in the position of RV body which have strong bearing force
Installation points ①& ②, ③& ④, ⑤& ⑥must be in the same horizontal position
Installation points ① & ⑤, ②& ⑥must be in the same vertical position
1. Please open the package, and check all the accessories according to the part list are complete.
2. Please confirm that install tools are ready, such as hand drill, tape measure, screwdriver,
marker pen and Ladders Etc.
3. According to your purchased awning size, mark the 6 fixation points for installation.
(The six fixation-points positions should be calculated according to the calculation formula bellow)
Total Width (Bottom)
Awning Width
Total Width (Upper)
Fabric lock Width
Fabric Width
Back Channel Details
Back Channel
5
6
Imperial Size
Measurement position sheet Unit:ft/in
8’9’10’11’12’13’14’15’16’17’18’19’20’21’
A-5.12
A+2.95
A-9.84
A+2.36
77.17
8
Installation Steps
Step.1
a
d
ce
REMARK:
Awning Width (A)
Fabric lock Width
Fabric Width
Total Width (Bottom)
Folded arm Height
Extension (Max.)
Total Width (Upper)
“A”=Awning width (Left arm center to right arm center)
Please check the above measurement sheet carefully, and calculate the correct installation
position accordingly.
1. Please open the plastic protection sleeve from two arms first. ( Attention: This is gas piston arm,
it will open automatically when the sleeve is released, when you take out sleeve, please firmly
grasp the arms and observe your surroundings, to avoid personal injury and product damage),
see Pic.1
〃
〃
〃
〃
〃
〃
b
Pic.1
protect sleeve cover
7
If you choose our modular type(W5700C)
Please connect the fabric tube first before
you start Step 2
ATTENTION !
1. Connect the fabric tube
abc
2. Install the open arm in the pre-marked installation position, as shown in Pic.2 & Pic.3-a.
Please put the belt behind the arm before installation, see Pic. 3-b.
3. After arms are fixed, please use offered belt tie up the left & right arm , avoiding private injure
see pic.3-c
Please find the fabric roller tube (right side cover with a motor and wire, left side only have a cover,
and the rest is the middle part). And take out the tube connector from the roller tube then connect
all tubes with M6X16 Screws piece by piece. see bellow pics.( please be sure all three sides tube
fix tight, or the tube will be curved easily during operation).
a
fabric tube fabric tube
fabric tube connector
b
fabric tube
fabric tube connector
Pic.2
Pic.3
2. Roller tube fabric fixation
Step.2
c
2
d
1
2
3
f
c
fabric tube
fabric tube connector
a. Insert the poly cord into valance fabric slop.See Pic.a
b. Finished step “a” and slide the valance fabric into groove No.1. See Pic.b
c. Pull the fabric to hole No.2 direction.
d. Fold the fabric and then insert it to punched hole No.2
e. Slide the poly cord to hole NO.2 and then fix roller tube fabric well.
f. Rolling the fabric towards the roller tube clockwise direction( Groove NO.1 direction).
Please fix the fabric lock rail on the wall of the car, see pic.4
Remark: After installing, please use structural glue on the back of fabric lock rail in case of water
leakage
d
a
Poly cord
Fabric
b
1
e
Poly cord
8Pic.4
Step.3
Step.4
Fabric fixation on Car
Step.6
Find out the poly cord and get across fabric loop, then put the fabric into the fabric lock rail,
see Pic.5
Please install the roller tube on the left arm and right arm , see PIC.6
Remark: Please Be sure the connect motor part is on right arm.
After installing the roller tubes, loosen the ropes on the arms (the arms will be slightly opened but
not completely opened), in this case, temporarily connect the motor, switch and power supply,
operate method as Step9.
Adjust the motor limit position when power on, operate method Step10.
Step.5
After Done Step 5, please open and close the awning normally, and ensure if the fabric is plan &
smooth. If not, please pull the fabric to adjust it well. After you confirm fabric is ok, please use the
self-tapping screws to fix fabric on both end of fabric locking rail,see Pic.7
Fabric
poly cord
9
Pic.5
Pic.6
Pic.7
Tabla de contenidos
