AVT MAGIC ACX DANTE WAN BRIDGE Manual de usuario
MAGIC ACX
DANTE WAN BRIDGE
Configuration Guide
Version 1.000 (13 December 2019)
© 2019, AVTAudio Video Technologies GmbH
Overview
▪Hardware
▪Interfaces
▪Features
PC Software
▪Operation
▪Local Settings
▪Configuration Overview
▪Operation Settings
▪System Settings
▪Miscellanea
Front Display
Annex
▪Dante
▪Support
2
Content
MAGIC ACX
DANTE WAN BRIDGE
Overview
Hardware,
Interfaces,
Features
3
Front View
Five Status-LEDs
▪POWER, SYNC, ALARM, INPUT 1, INPUT 2
Illuminated graphic display with 160 x 32 pixels & front keypad
▪For configuration and status.
4
Rear view
Two independent LAN interfaces for control
and VoIP applications.
Word clock input/output
Programmable GPIO interface
▪8 x TTL input/output
▪8 x Relays (8 x normally open contact)
Redundant Power Supply (optional)
Slot 1: unused
Slot 2: Dante
▪32 channels
▪2 Ethernet interfaces
5
Features
6
19” housing x 1 U
Without fan for silent
operation
Low power consumption of
typ. 15 W
Optional redundant power
supply
VLAN support
QoS support
32 Dante channels
Supports a Dante audio
sampling rate of 48 kHz.
Up to 5 Control-PCs can
connect to the system
simultaneously.
MAGIC ACX
DANTE WAN BRIDGE
PC Software Operation
7
Starting the PC Software
8
Install the MAGIC ACX Software with administrator
rights on your PC and then start the software with
administrator rights.
▪From Windows 7 and higher via the context menu "Run
as administrator", even if you are currently logged on
as administrator.
Under MENU →CONFIGURATION →CONTROL
INTERFACE, enter the systems to be controlled.
Add systems by double-clicking a line or use the
ADD/EDIT key.
Remove a system using DELETE.
DELETE ALL removes all entries from the list.
The order of the entries can be changed via UP
and DOWN. The sequence determines the order
of the systems in the main window.
Connection parameters
9
INTERFACE: The connection to the device
is established via the LAN interface (UDP).
PARAMETERS:
▪INTERFACE: If the PC has several network
interfaces, specify here which of them is to be
used.
▪IPADDRESS: IP address of the MAGIC ACX.
▪PORT: UDP port of the control connection on
the MAGIC ACX. The default value is 10 000.
Press the HANG UP key (to the right of the
OK key) on the device twice to display the
currently assigned IP address of the
system.
The network settings may be configured on
the device under MENU →SYSTEM
SETTINGS →LAN SETTINGS.
Main Window (1)
10
The software can connect to up to
10 MAGIC ACX systems
simultaneously.
The MAGIC ACX systems can be
distributed over up to 10 pages.
The pages are selected via tabs
().
Depending on the screen
resolution, up to 10 MAGIC ACX
systems can be displayed
simultaneously on one page.
Tabla de contenidos
Otros manuales de Convertidor de medios de AVT
AVT
AVT MAGIC AE4 Manual de usuario
AVT
AVT MAGIC AE4 Manual de usuario
AVT
AVT MAGIC AE4 Manual de usuario
AVT
AVT MAGIC ACX Dante WAN Manual de usuario
AVT
AVT MAGIC AE1 DAB+ Manual de usuario
AVT
AVT MAGIC DAB Instrucciones de funcionamiento e instalación
AVT
AVT MAGIC AE1 DAB+ Manual de usuario
AVT
AVT MAGIC AD1 ETI Manual de usuario
AVT
AVT MAGIC AE1 DAB+ Instrucciones de montaje
AVT
AVT MAGIC EEC Instrucciones de montaje
