AVLink IEB22 Manual de usuario
I
IIE
E
EB
B
B-
-
-2
2
22
2
2
0
User Manual
Projector
Edge Blending
V.2018 IEB-22 10
I
IIE
E
EB
B
B-
-
-2
2
22
2
2
1
COPYRIGHT AND TRADEMARKS
All rights reserved by AVLINK GROUP LTD., No part of this document may be
reproduced in any form or by any means without written permission from the product
manufacturer. Changes are periodically made to the information in this document.
They will be incorporated in subsequent editions. The product manufacturer may make
improvements and /or changes in the product described in this document at any time.
All the registered trademarks referred to this manual are belonging to their respective
companies.
I
IIE
E
EB
B
B-
-
-2
2
22
2
2
2
BEFORE YOU BEGIN
Follow all instructions marked on the device during using.
Provide proper ventilation and air circulation and do not use near water.
It is better to keep it in a dry environment.
Place the device on a stable surface (example cart, stand, table, etc.).
The system should be installed indoor only. Install either on a sturdy rack or desk in a
well-ventilated place.
Make sure the rack is level and stable before extending a device from the rack if
necessary.
Make sure all equipments installed on the rack including power strips and other
electrical connectors are properly grounded.
Only use the power cord supported with the device.
Do not use liquid or aerosol cleaners to clean the device.
Always unplug the power to the device before cleaning.
Unplug the power cord during lightning or after a prolonged period of non-use to avoid
damage to the equipment.
Do not stand on any device while installing the device to the rack.
Do not attempt to maintain the device by yourself, any faults, please contact your
vendor.
Save this manual properly for future reference.
I
IIE
E
EB
B
B-
-
-2
2
22
2
2
3
TABLE OF CONTENTS
Copyright and Trademarks..........................................................................................................1
Before You Begin..........................................................................................................................2
Table of Contents..........................................................................................................................3
List of Figures................................................................................................................................4
Chapter 1 Overview......................................................................................................................5
1.1 Introduction....................................................................................................................5
1.2 Packing...........................................................................................................................6
1.3 Applications ...................................................................................................................6
Chapter 2 Features ......................................................................................................................7
Chapter 3 Specifications..............................................................................................................8
Chapter 4 Installation...................................................................................................................9
Chapter 5 Front/Rear Panels....................................................................................................10
5.1 Front Panel..................................................................................................................10
5.2 Rear Panel...................................................................................................................11
5.3 Connectors..................................................................................................................12
Chapter 6 Connections..............................................................................................................13
6.1 Input Connection.........................................................................................................13
6.2 Output Connection .....................................................................................................14
6.3 Micro USB Connection..............................................................................................14
6.4 Audio Output Connection..........................................................................................15
6.5 Power Connection......................................................................................................15
Chapter 7 Troubleshooting........................................................................................................16
I
IIE
E
EB
B
B-
-
-2
2
22
2
2
4
LIST OF FIGURES
Figure 1-1: IEB-22...............................................................................................................5
Figure 4-1: IEB-22 with 1U Rack-Mount Bracket...........................................................9
Figure 4-2: Place the device on a Sturdy Surface.........................................................9
Figure 5-1: IEB-22 Front Panel.......................................................................................10
Figure 5-2: IEB-22 Rear Panel....................................................................................... 11
Figure 5-3: HDMI Connector...........................................................................................12
Figure 5-4: Micro USB Connector..................................................................................12
Figure 6-1: IEB-22 Connections.....................................................................................13
Figure 6-2: Input Connection-HDMI...............................................................................13
Figure 6-3: Outpu Connection-HDMI.............................................................................14
Figure 6-4: Micro USB Connection................................................................................14
Figure 6-5: Audio Output Connection............................................................................15
Figure 6-6: Power Connection........................................................................................15
I
IIE
E
EB
B
B-
-
-2
2
22
2
2
5
CHAPTER 1 OVERVIEW
1.1 Introduction
The IEB22 is a projector edge blending consists of multiples projectors lied
together contiguously or overlapped in order to form one large screen. Use typical
display technologies and mullion compensation with seamless output feature.
The IEB22 is a two-channel image processor that supports 1080P high resolution
signal input and can be used to combine multi projector planes. Advanced
geometry adjustment techniques are embedded in the IEB22. Users can perform
edge blending and completes geometric adjustments through PC tools. Each
projector can be independently color (white balance) adjusted, overlap area color
corrected, and precise non-overlapping areas with dark levels raised.
Moreover, while color temperature dramatically affects the picture qualities of an
LCD monitor. User can simply use the default values to restore the picture basic
quality. A good understanding of the meaning of color temperature will enable
better adjustments of LCD monitor picture quality.
Through the HDMI (IEB-22) interfaces you can optional select output transmission
mode featuring a high resolution and low energy consumption. Typical application
areas of the crescent walls include information displays, digital advertisings,
meeting rooms and so on.
Figure 1-1: IEB-22
I
IIE
E
EB
B
B-
-
-2
2
22
2
2
6
1.2 Packing
IEB-22 (H) x 1
12V/5A Power adaptor x 1
CD Manual x 1
HDMI cable x 4
Micro USB cable x 1
1.3 Applications
Edge blending can be used to display information for:
Public and Emergency Services
Telecommunications
Power and Utilities
Data Monitoring
Broadcast
Show room
Interactive scene
I
IIE
E
EB
B
B-
-
-2
2
22
2
2
7
CHAPTER 2 FEATURES
Projector edge blending can be configured as overlap adjustment through
convenient computer tools.
The computer tools are user-friendly and flexible, allowing users to easily
operate.
Color temperature adjustments
Supports USB connector for connect the IEB-22 with computer.
Supports HDMI connector for output display identical image on local side
HDMI output
- Supports 2 HDMI connector for input and 2 HDMI connectors for HDMI
output interfaces
Supports HDMI interface or S/PDIF interface for audio output.
Supports HDMI Remote Extender (Optional)
Supports resolution up to 1080P for each edge blending screen.
12V power adaptor
1U rack design.
I
IIE
E
EB
B
B-
-
-2
2
22
2
2
8
CHAPTER 3 SPECIFICATIONS
Hardware
Input Connector
HDMI Type A Female:
- IEB-22 (H) x 2
Output Connector
HDMI Type A Female (Local Video Output):
- IEB-22 (H) x 2
USB Connector
Micro USB type x 1
Audio port
Digital Optical Toslink x 1
RCA Digital Audio x 1
Power
DC/12V
LED Indicator
Device/Signal Status x 8
Housing
Metal
Mounting
Rack mountable (1U-rack-mount kit)
Weight
IEB-22 (H): 2.85Kg
Dimensions (LxWxH)
IEB-22 (H): 444x222x44 mm
Multimedia
Max. Resolution
1080P for each TV
Control Information
HDMI Cable Distance
Local: 10 meters (Max.) / Remote: 10 meters (Max.)
I
IIE
E
EB
B
B-
-
-2
2
22
2
2
9
CHAPTER 4 INSTALLATION
IEB-22 has a black metallic housing. It can be placed on a sturdy desk directly or
installed on a bracket. You can also use the rubber feet pasted on the bottom of the
chassis to protect your device when you want to place the device on a working desk.
Figure 4-1: IEB-22 with 1U Rack-Mount Bracket
Attach the rubber feet to the bottom of the device, Place the device on a sturdy, level
surface that can support the weight.
Figure 4-2: Place the Device on a Sturdy Surface
Tabla de contenidos
