AVLink BNC90 Manual de usuario

Active noise cancelling Bluetooth headphone

Model No.: BNC90

User manual

Important Safety Instruction

If used in the correct method, this design and production of this product can ensure

your personal safety completely. However, any inappropriate use may lead to

potential risk and danger of electric shock or fire hazard. Please read all the safety

instructions before installing and using the product. In particular, attention shall be

given to the following information:

1. It needs to be stored or used in the ambient temperature.

2. It shall not be placed in water or wet locations.

3. It cannot be disposed randomly because it may cause environmental pollution.

4. Without approval, it shall not be disassembled or repaired.

5. The built-in lithium battery can’t be disposed in the fire or other places to

prevent causing fire hazards.

6. It shall be cleaned with dry cloth.

7. Whenever there is damage, it needs to be repaired by professional personnel.

Headphone overview

Functions

Button operation

Power on

Press and hold the MFB until the LED indicator flash green once

then flash in green and red alternatively

Power off

Press and hold the MFB until the LED indicator flashes red once

then goes off

Calls

operation

1. To answer an incoming call, tap the MFB button once; tap once

again to hang up the call. Press and hold the button twice to

reject the incoming calls

2. During the call, press and hold the MFB button for 2 seconds to

seamlessly switch the conversation between the headphone

and the mobile phone

3. When an incoming call from the third party occurs during the

call, tap the MFB button to hang up the current call and to

answer the third part’s coming call; press and hold the MFB

button to put the call on hold and to answer the third party’s

incoming call.

4. When Bluetooth is connected, press and hold the MFB button

for 2 seconds to retrie

Volume

control

Adjust the volume wheel to adjust the control until it reaches to

your desired one.

Play / pause

Tap the “MFB” once to pause music when the music is playing; Tap

once again to continue playing the music

Previous /

Next tracking

While the music is playing, tap forward button once to next track;

To move to the previous tracking, tap backward button once.

Pairing the device

1. Making sure there is power remaining in .

2. Press and hold the “MFB” button until the Led indicator flashes in green once

then in green and red alternatively which indicates that the headphone enter

had entered into pairing mode.

3. Enable searching of nearby Bluetooth devices using the Bluetooth menu on your

device.

4. Select “ ” from the Bluetooth device list on your mobile phone. If connected, the

headphone will enter into standby mode.

can be paired with two Smartphone at the same time.

If was previously paired to a Smartphone, it is possible to be paired with a 2nd

Smartphone: restart (switch off and switch on) to enter pairing mode; repeat the

above pairing procedure to pair with the 2nd Smartphone; and then reconnect with

1st Smartphone; finally two Smartphone can connect with .

Note:

1. The headphone will automatically connect the last paired device once it is in

effective range.

2. The headphone will be turned off automatically if no device connected within 10

minutes.

To clear the pairing list

Power on the headphone, then press and hold the forward button and backward

button until the left Led indicator flashes yellow 3 times then in green 1once every

second.

ShareMe Function

Two headphones are connected to the same device to listen to the same music or

audio program at the same time.

ShareMe paring

1. Turn two headphones to be in the paring mode together (by press and hold the

MFB until the indicator flashes yellow) and these two headphones will complete

the pairing process automatically. After the pairing process is completed, the

indicator of the secondary headphone will light up green automatically; while the

primary headphone continuously flash red and green alternatively and waits to

be paired with the portable device.

2. Activate the Bluetooth of the portable device and select “ ” from the list found. If

the pairing process is completed, the LED indicator of both headphones keep in

regular green 1 second then flash green 3 times every 3 second. This signal that

the headphones enter into standby modes.

Using ShareMe

Every time you will have to complete the ShareMe paring before using both

headphones to provide same music or audio programs at the same time.

When the secondary headphone is turned off which both headphones are in use, the

primary headphone will not be affected and can be in use continuously. If the

primary headphone is turned off first and the secondary headphone is still expected

to be in use, the indicator of the secondary headphone will return to standby mode

and flash green 1 once every second. You will have to manually pair the headphone

with a device. This is a once process. Afterward, the user only needs to tap the MFB

of the secondary headphone to reconnect with the device.

ShareMe button control

Call operation

1. To answer an incoming call, tap the MFB once;

tap the “MFB” again to hang up. Press and

hold the MFB for 2 seconds to reject the

incoming calls.

Only work for

the primary

headphone

2. During the call, press and hold the MFB to

hang up for 2 seconds to seamlessly switch the

conversation between the headphone and the

mobile phone.

3. When an incoming call from the third party

occurs during the call, tap the MFB to hang up

the current call and to answer the third party’s

incoming call; Or press and hold the MFB to

put the call on hold and to answer the third

party’s incoming call.

4. When Bluetooth is connected, press and hold

the MFB for 2 seconds to retrieve the last

dialed number

Play /pause

Tap the MFB once

Both

headphones

can control

simultaneously

Volume

control

Adjust the volume wheel until

Previous /

next tracking

While the music is playing, tap forward button

once to next track; To move to the previous

tracking, tap backward button once.

Note:

1. When one headphone is connected to the device, the effective range of the

Bluetooth is 10 meters. When two headphones are connected to the device, the

effective range of the Bluetooth between two headphones is 5 meters.

2. The headphone will be turned automatically when a 3.5mm audio cable inserted

into the headphone while the Bluetooth is connected.

3. The paring statues will last for 5 minutes.

4. The headphone will be turned off automatically if no device connected within 10

minutes.

Active Noise Cancelling Mode:

• Adjust the volume on the headphones.

• To power ON the noise cancelling function, set the ON/OFF switch to ON position.

The Noise Cancelling LED indicator will light up in green.

Note: After you turn ON the power, you might hear a slight hissing noise. This is a

normal function and will cease after a few seconds.

• When the batteries are running low, the Noise Cancelling LED indicator will

become dim.

• Once the battery is fully drained, the active noise cancelling feature will turn off

but the audio signal from the music player will continue to transmit.

• In quiet environments where noise cancellation is not required, the BNC50 can also

be used like conventional headphones, without the use of batteries.

• When not in use, switch OFF the POWER to extend battery life.

External audio resource play

Connect the external audio sources with the RIGHT AUX jack on the headphone by

3.5mm audio cable.

External 3.5mm microphone

To add a external microphone, connect the included 3.5mm microphone with the

LEFT AUX jacket on the headphone. The external microphone will have priority over

the internal 3.5mm microphone when the external microphone is inserted into the

headphone.

Charging the battery

Fully charge the battery for about 2 hours before using this headphone for the first

time.

Plug the smaller end of USB charging cable into the micro-USB interface of the

connector.

Next, plug the other end of the USB charging cable into other power charging

devices or a computer with the power on. The led indicator will keep in red during

charging, it will go off when the headphone is fully charged.

Note: When charging the headphone meanwhile the headphone is connected with

Bluetooth, the headphone will be turned off automatically.

Trouble shooting

Q1. Why can’t I power on the headphone?

A1: The headphone may have run out of the battery power. Please charge the

battery via the included charging cable.

Q2. Why can’t I connect the headphone to my Bluetooth device?

A2.1. The Bluetooth function on your device may have been turned off. Please turn

on the Bluetooth function on your device and allow it to search for compatible

devices.

A2.2 The headphone may have been connected to another device. Please disconnect

(unpaired) the headphone from the previous device before connecting them to a

new one.

A2.3. The headphone may not have been recognized by your device.

Please turn off the headphone, turn them back on, and search for the headphone on

your Bluetooth enabled device, and make the connection again.

A2.4. The headphones may be too far away from your Bluetooth device. Please make

sure that the headphones are close enough to your device and there is no obstacle

between them.

Q3. Why aren’t the headphones playing sound tracks in the Bluetooth mode?

A3.1. The headphones may not have selected as the output device. Please adjust the

setting on your Bluetooth enabled device to use the headphones to play the sound

tracks.

A3.2. The volume may have been adjusted to the minimum. Please adjust the sound

wheel to reach desired volume.

Q4. Why is the sound quality very poor in the Bluetooth mode?

A4.1: The Bluetooth connection may not be in its optimal condition. Please make

sure that the headphones are close enough to your device, and there is no obstacle

between them.

Product Specifications:

1. Bluetooth version: 4.1

2. Bluetooth chipset: CSR8670 with aptX Low Latency

3. Noise cancellation rate: approximately 90%

4. Bluetooth profiles: HFP, HSP, A2DP, AVRCP, AAC, aptX, aptX Low Latency

5. Speakers: 40mm neodymium

6. Audio impedance: 32Ohm

7. Charging time: about 3 hours

8. Charging: Micro USB

9. Bluetooth operating range: ≥10 m

10. Connection: 3.5mm jack

11. Battery time (Bluetooth only): 15 hours

Battery time (Noise cancelling only): 25 hours

Battery time (Bluetooth + noise cancelling): 9 hours

12. Battery type: Li-Polymer

Package content

1. Headphone

2. Micro USB charging cable

3. 3.5mm audio cable

4. Detachable microphone

5. 1/4’’ stereo-plug adapter

6. Dual plug adapter

7. Hard carrying case

8. User manual

9. Detachable external 3.5mm microphone

FCC ID:R2M-BNC90

NOTE: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help

Changes or modifications not expressly approved by the party responsible for

compliance

could void the user's authority to operate the equipment. This device complies with

Part

15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

Tabla de contenidos

Otros manuales de Auriculares de AVLink

AVLink

AVLink 100.642UK Manual de usuario

AVLink

AVLink Ear Shots Active Manual de usuario

AVLink

AVLink Ear Shots II Manual de usuario

AVLink

AVLink 100.585UK Manual de usuario

AVLink

AVLink Isolate Manual de usuario

AVLink

AVLink SFBH1 Manual de usuario

AVLink

AVLink InSound 100.580UK Manual de usuario

AVLink

AVLink JOGS Manual de usuario

AVLink

AVLink WBH-40 Manual de usuario

AVLink

AVLink TWE1 Manual de usuario

AVLink

AVLink Resonate Manual de usuario

AVLink

AVLink 100.563UK Manual de usuario

AVLink

AVLink Ear Shots II Manual de usuario

AVLink

AVLink TWS20 Manual de usuario

AVLink

AVLink PBH10 Manual de usuario

AVLink

AVLink Ear Shots II Manual de usuario

AVLink

AVLink Ear Shots II Manual de usuario

AVLink

AVLink BT204 Manual de usuario

AVLink

AVLink NEO Manual de usuario

AVLink

AVLink PBH10 Manual de usuario

AVLink

AVLink InFuse Manual de usuario

AVLink

AVLink BNC100 Manual de usuario

AVLink

AVLink EMBT1 Manual de usuario

AVLink

AVLink 100.571UK Manual de usuario

Manuales populares de Auriculares de otras marcas

Sony

Sony MDR-NC8 Manual de usuario

AUSounds

AUSounds AU-Stream Manual de usuario

ENERGY SISTEM

ENERGY SISTEM Style 7 Manual de usuario

Philips

Philips SHE3622 Manual de usuario

Insignia

Insignia NS-CAHBTSPORT Manual de usuario

Movie Vision

Movie Vision HP-400 Manual de usuario

MobiFren

MobiFren SM Pro Manual de usuario

Motorola solutions

Motorola solutions PMLN8120 Manual de usuario

Jaybird

Jaybird freedom Guía de instalación

Sony

Sony MDR-ED12LP Manual de usuario

HiFuture

HiFuture Tidy Buds Pro Manual de usuario

Creative

Creative CB2530 Manual de usuario

Renkforce

Renkforce RF FTVK-100 Manual de usuario

Philips

Philips SHQ3000 Manual de usuario

Sennheiser

Sennheiser 500371 Manual de usuario

Califone

Califone 2924AV Manual de usuario

Philips

Philips EARGEAR HE205 Series Manual de usuario

Technics

Technics EAH-AZ80 Manual de usuario