Avinity ABT-632 Manual de usuario

Operating Instructions

Bedienungsanleitung

Mode d‘emploi

Instrucciones de uso

Руководство по эксплуатации

PURE IMAGE–PURESOUND –PUREPASSION

00107632

1 5

2 4

GOperating instruction

Avinity: High Performance Accessories –born

of apassion for audio/video entertainment.

High-quality workmanship and performance

emphasise our commitment to premium

accessories.

Take your time and read the following in-

structions and information completely.Keep

these operating instructions in asafe place

for future reference.

Explanation of Warning Symbols and Notes

Warning

This symbol is used to indicate safety

instructions or to draw your attention to

specichazards and risks.

Note

This symbol is used to indicate additional

information or important notes.

2. Package Contents

•Bluetooth® transmitter/receiver,

2-in-1 adapter

•3.5 mm jack cable

•Micro-USB charging/connecting cable

•These operating instructions

3. Safety Notes

•The product is intended for private,

non-commercial use only.

•Protect the product from dirt, moisture

and overheating, and only use it in adry

environment.

•Do not use the product in the immediate

vicinity of heaters or other heat sources or

in direct sunlight.

•Do not allow yourself to be distracted by

the product, for example when driving ave-

hicle or operating sports equipment. Always

pay attention to the surrounding tracand

your environment.

•Do not drop the product and do not expose

it to any major shocks.

•Do not operate the product outside the

power limits given in the specications.

•Do not open the device or continue to

operate it if it becomes damaged.

•Since the battery is integrated and cannot

be removed, you will need to dispose of the

product as awhole. Do this in compliance

with the legal requirements.

•Dispose of packaging material immediately

according to locally applicable regulations.

•Do not modify the product in any way.

Doing so voids the warranty.

Warning –Rechargeable battery

•Only use suitable charging devices or

USB connections for charging.

•As arule, do not use charging devices

or USB connections that are defective

and do not try to repair them yourself.

•Do not overcharge the product or allow

the battery to completely discharge.

•Avoid storing, charging or using

batteries in extreme temperatures.

•When stored over along period of time,

batteries should be charged regularly

(at least every three months).

4.Getting Started

•The adapter is equipped with arecharge-

able battery.The battery must be fully

charged before using the device for the

rst time.

•Begin charging by connecting the included

Micro-USB charging/connecting cable to

the adapter’s Micro-USB connection (5)

and to asuitable USB charger.Please refer

to the operating instructions for the USB

charger used.

•The adapter’s status LED (3) emits acon-

stant red light during charging.

•It can take up to 2hours to fully charge the

battery.

•Charging begins and ends automatically.

5. Operation

5.1. Switching the adapter on/o

•Switching on:

With the device o,press and hold the

multifunction button (2) for 3seconds. The

status LED (3) lights up in blue.

•Switching o:

With the device on, press and hold the

multifunction button (2) for 3seconds. The

status LED (3) emits two red ashes before

the device turns o.

The rst time the device is turned on, pairing

is automatically started –see 5.2 Blue-

tooth®pairing in receiver (RX) mode.

5.2.

Bluetooth®pairing in receiver (RX) mode

Note –Pairing

•Make sure that your Bluetooth®-ca-

pable terminal device is on and

Bluetooth® is activated.

•For more information, please refer

to the operating instructions of your

terminal device.

•Connect your terminal device to the adapt-

er using the included 3.5 mm jack cable

and the audio connection (AUX) (4).

•Select the adapter’s RX mode by moving

the switch (1) to the right.

•The adapter and the terminal device should

be no further than 1metre apart. The short-

er the distance, the better.

•With the adapter on, press the multifunc-

tion button (2) twice. After approximately

3seconds, the status LED (3) will emit

ashes of alternating blue and red light to

indicate the device is in pairing mode.

•Open the Bluetooth®settings on your

terminal device and wait until Avinity

BTT-632 appears in the list of Bluetooth®

devices found.

•Select Avinity BTT-632 and wait until the

adapter is listed as connected in the Blue-

tooth®settings on your terminal device.

Note –Bluetooth®password

Some terminal devices require a

password in order to connect to another

Bluetooth®device.

•If your terminal device requests a

password to establish the connection,

enter 0000, 1234, 1111 or 8888.

Note

If pairing was successful, the status LED

(3) lights up in blue.

•Youcan now use the adapter.

5.3. Bluetooth®pairing in transmitter (TX)

mode

Note –Pairing

•Make sure that your Bluetooth®-

capable terminal device is on and

Bluetooth® is activated.

•For more information, please refer

to the operating instructions of your

terminal device.

•Connect your terminal device to the adapt-

er using the included 3.5 mm jack cable

and the audio connection (AUX) (4).

•Select the adapter’s TX mode by moving

the switch (1) to the left.

•Turn on Bluetooth®on your Bluetooth®

headphones/speaker.

•For more information, please refer to the

operating instructions of your terminal

device.

•The adapter and the Bluetooth®headphones/

speaker should be no further than 1metre

apart. The shorter the distance, the better.

•With the adapter on, press the multifunc-

tion button (2) twice. After approximately

3seconds, the status LED (3) will emit

ashes of blue light to indicate the device

is in pairing mode.

•The connection is now established auto-

matically.

5.4. Automatic Bluetooth®connection

(after successful pairing)

Note –Pairing

•Make sure that your Bluetooth®-

capable terminal device is on and

Bluetooth® is activated.

•For more information, please refer

to the operating instructions of your

terminal device.

•Make sure that the adapter is on.

•After the devices have been paired once, the

connection is then established automatically.

•Youcan now use the adapter.

Note

•If pairing was successful, the status

LED (3) will be lit blue.

•It may be necessary to make settings

on your terminal device to enable auto-

matic connection to the paired adapter.

Note –Connection impaired

After the devices have been paired

once, the connection is then estab-

lished automatically.Ifthe Bluetooth®

connection is not established automati-

cally,check the following:

•Check the Bluetooth® settings of your

terminal device to see whether Avinity

BTT-632 is connected.

•If not, repeat the steps listed in 5.2

Bluetooth® pairing.

•Check whether obstacles are impairing

the range. If so, move the devices

closer together.

•The performance can also be aected

by aweak battery.

5.5. Pairing in transmitter (TX) mode with

two devices at the same time

•Switch on the adapter and your two

Bluetooth®-capable audio devices (BT

headphones/speaker) as described in 5.2

Bluetooth®pairing.

•The adapter automatically names the two

terminal devices Aand B, and establishes a

connection.

5.6. Deleting the pairing list

•Switch othe adapter in the current mode

(TX or RX). After approximately 3seconds,

move the switch (1) to the other mode

and switch the adapter on again; this will

delete all paired devices from the list.

5.7. Battery capacity

•The status LED (3) begins ashing red when

the battery charge is low.

•Charge the adapter as described in 4.

Getting started.

6. Care and Maintenance

Only clean this product with aslightly damp,

lint-free cloth and do not use aggressive

cleaning agents.

7. Warranty Disclaimer

Hama GmbH &Co. KG assumes no liability

and provides no warranty for damage result-

ing from improper installation/mounting,

improper use of the product or from failure

to observe the operating instructions and/or

safety notes.

8. Service and Support

Please contact Hama Product Consulting if

you have any questions about this product.

Hotline: +49 9091 502-115 (German/English)

Further support information can be found

here: www.hama.com

9. Technical Data

Bluetooth®version 4.1

Prole A2DP

Range <10m

Battery type

Lithium polymer

rechargeable

battery

Frequency band(s)

2402 –2480 MHz

Maximum radio-

frequency power

transmitted

3.94 mW E.I.R.P.

Input 240 mA

Charging time Approx. 2h

Battery life of Blue-

tooth®transmitter Approx. 13 h

Battery life of

Bluetooth®receiver Approx. 12 h

10. Recycling Information

Note on environmental protection:

After the implementation of the

European Directive 2012/19/EU and

2006/66/EU in the national legal

system, the following applies: Electric

and electronic devices as well as batteries

must not be disposed of with household

waste. Consumers are obliged by law to return

electrical and electronic devices as well as

batteries at the end of their service lives to

the public collecting points set up for this

purpose or point of sale. Details to this are

dened by the national law of the respective

country.This symbol on the product, the

instruction manual or the package indicates

that aproduct is subject to these regulations.

By recycling, reusing the materials or other

forms of utilising old devices/Batteries, you

are making an important contribution to

protecting our environment.

11. Declaration of Conformity

Hereby,Hama GmbH &CoKGdeclares

that the radio equipment type

[00107632] is in compliance with

Directive 2014/53/EU. The full text of the EU

declaration of conformity is available at the

following internet address:

www.hama.com->00107632-> Downloads.

DBedienungsanleitung

Avinity: High Performance Accessories –

geboren aus der Leidenschaft für Audio/Video

Entertainment. Hochwertige Verarbeitung und

Performance unterstreichen unseren Anspruch

an Premium Zubehör.

Nehmen Sie sich Zeit und lesen Sie die folgen-

den Anweisungen und Hinweise zunächst ganz

durch. Bewahren Sie diese Bedienungsanlei-

tung anschließend an einem sicheren Ort auf,

um bei Bedarf darin nachschlagen zu können.

Erklärung von Warnsymbolen und Hinweisen

Warnung

Wird verwendet, um Sicherheitshinweise

zu kennzeichnen oder um Aufmerksam-

keit auf besondere Gefahren und Risiken

zu lenken.

Hinweis

Wird verwendet, um zusätzlich Infor-

mationen oder wichtige Hinweise zu

kennzeichnen.

2. Packungsinhalt

•Bluetooth®-Sender/-Empfänger,

2in1-Adapter

•3,5-mm-Klinkenkabel

•Micro-USB-Lade-/Verbindungskabel

•diese Bedienungsanleitung

3. Sicherheitshinweise

•Das Produkt ist für den privaten, nicht-ge-

werblichen Haushaltsgebrauch vorgesehen.

•Schützen Sie das Produkt vor Schmutz,

Feuchtigkeit und Überhitzung und verwen-

den Sie es nur in trockenen Umgebungen.

•Betreiben Sie das Produkt nicht in unmittel-

barer Nähe der Heizung, anderer Hitzequel-

len oder in direkter Sonneneinstrahlung.

•Lassen Sie sich auf der Fahrt mit einem

Kraftfahrzeug oder Sportgerät nicht durch

Ihr Produkt ablenken und achten Sie auf die

Verkehrslage und Ihre Umgebung.

•Lassen sie das Produkt nicht fallen und

setzen Sie es keinen heftigen Erschütterun-

gen aus.

•Betreiben Sie das Produkt nicht außerhalb

seiner in den technischen Daten angegebe-

nen Leistungsgrenzen.

•Önen Sie das Produkt nicht und betreiben

Sie es bei Beschädigung nicht weiter.

•Der Akku ist fest eingebaut und kann nicht

entfernt werden, entsorgen Sie das Produkt

als Ganzes gemäß den gesetzlichen Bestim-

mungen.

•Entsorgen Sie das Verpackungsmaterial

sofort gemäß den örtlich gültigen Entsor-

gungsvorschriften.

•Nehmen Sie keine Veränderungen am Gerät

vor.Dadurch verlieren Sie jegliche Gewähr-

leistungsansprüche.

Warnung –Akku

•Verwenden Sie nur geeignete Ladegerä-

te oder USB-Anschlüsse zum Auaden.

•Verwenden Sie defekte Ladegeräte oder

USB-Anschlüsse generell nicht mehr und

versuchen Sie nicht, diese zu reparieren.

•Überladen oder tiefentladen Sie das

Produkt nicht.

•Vermeiden Sie Lagerung, Laden und

Benutzung bei extremen Temperaturen.

•Laden Sie bei längerer Lagerung regel-

mäßig (mind. vierteljährig) nach.

4. Inbetriebnahme

•Der Adapter verfügt über einen wieder auad-

baren Akku. Vorder ersten Anwendung muss

der Akku vollständig aufgeladen werden.

•Starten Sie den Ladevorgang, indem Sie das

beiliegende Micro-USB-Lade-/Verbindungs-

kabel an den Micro-USB-Anschluss (5) des

Adapters und an ein geeignetes USB-La-

degerät anschließen. Beachten Sie hierzu

die Bedienungsanleitung des verwendeten

USB-Ladegeräts.

•Die Status-LED (3) des Adapters leuchtet

während des Ladevorgangs dauerhaft rot.

•Es kann bis zu 2Stunden dauern, bis der

Akku vollständig geladen ist.

•Der Ladevorgang startet und endet automa-

tisch.

5.Betrieb

5.1. Ein-/Ausschalten des Adapters

•Einschalten:

Halten Sie im ausgeschalteten Zustand die

Multifunktionstaste (2) 3Sekunden lang ge-

drückt. Die Status-LED (3) leuchtet blau auf.

•Ausschalten:

Halten Sie im eingeschalteten Zustand die

Multifunktionstaste (2) 3Sekunden lang

gedrückt. Die Status-LED (3) leuchtet 2x rot

auf, bevor sich das Gerät abschaltet.

Beim ersten Einschalten wird automatisch

das Pairing gestartet –siehe 5.2. Bluetooth®

Erstverbindung (Pairing) im Empfänger-Mo-

dus RX.

5.2. Bluetooth®Erstverbindung (Pairing) im

Empfänger-Modus RX

Hinweis –Pairing

•Stellen Sie sicher,dass Ihr Bluetooth®-

fähiges Endgerät eingeschaltet ist und

dass Bluetooth® aktiviert ist.

•Beachten Sie hierzu die

Bedienungsanleitung Ihres Endgerätes.

•Für die Verbindung zum jeweiligen Endgerät

verbinden Sie es über das beiliegende

3,5 mm-Klinkenkabel und den Audio-An-

schluss (AUX) (4) mit dem Adapter.

•Wählen Sie den RX-Modus des Adapters,

indem Sie den Umschalter (1) nach rechts

schieben.

•Der Adapter und das Endgerät sollen nicht

weiter als 1Meter voneinander entfernt

sein. Je geringer der Abstand, desto besser.

•Drücken Sie zwei Mal die Multifunktionstas-

te (2) des eingeschalteten Adapters. Nach

ca. 3Sekunden blinkt die Status-LED (3)

abwechselnd blau und rot und signalisiert

dadurch den Kopplungsmodus.

Tabla de contenidos

Idiomas:

Manuales populares de Adaptador de otras marcas

PCB Piezotronics

PCB Piezotronics 090B274 Manual de usuario

Auvidea

Auvidea J20 Manual del producto

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manual de usuario

Akribis

Akribis ITF-21-BISS-MIT Manual de usuario

Tenda

Tenda W54U Manual de usuario

ROHO

ROHO AGILITY Manual de usuario

PROLiNK

PROLiNK WN2001 Manual de usuario

Hawking

Hawking HUF2 Manual de usuario

Airlink101

Airlink101 AWLC4030 Manual de usuario

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manual de usuario

Philips

Philips SWA4554S/10 Manual de usuario

JVC

JVC TS-C9D2B Manual de instrucciones

NETGEAR

NETGEAR A6100 Manual de usuario

D-Link

D-Link DWA-121 Manual de usuario

Philips

Philips SWA2037 Manual de usuario

Basalte

Basalte 0610-20 Manual de usuario

Yealink

Yealink EHS40 Manual de usuario

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manual de usuario