Avigilon NVR5-STD-16TB-W10 Manual de usuario
Installation Guide
Avigilon NVR5 Standard
NVR5-STD-16TB-W10, NVR5-STD-16TB-S19,
NVR5-STD-24TB-W10, NVR5-STD-24TB-S19,
NVR5-STD-32TB-W10, NVR5-STD-32TB-S19,
NVR5-STD-48TB-W10, NVR5-STD-48TB-S19,
NVR5-STD-64TB-W10, NVR5-STD-64TB-S19
© 2022,Avigilon Corporation. All rights reserved. AVIGILON, the AVIGILON logo, AVIGILON CONTROL
CENTER, and ACC are trademarks of Avigilon Corporation. Microsoft and Windows are trademarks of the
Microsoft group of companies. Dell is a trademark of Dell Inc. Other names or logos mentioned herein may be
the trademarks of their respective owners. The absence of the symbols ™ and ® in proximity to each
trademark in this document or at all is not a disclaimer of ownership of the related trademark.
This document has been compiled and published using product descriptions and specifications available at
the time of publication. The contents of this document and the specifications of the products discussed
herein are subject to change without notice. Avigilon Corporation reserves the right to make any such
changes without notice. Neither Avigilon Corporation nor any of its affiliated companies: (1) guarantees the
completeness or accuracy of the information contained in this document; or (2) is responsible for your use of,
or reliance on, the information. Avigilon Corporation shall not be responsible for any losses or damages
(including consequential damages) caused by reliance on the information presented herein.
Avigilon Corporation
avigilon.com
20220601
2
Table of Contents
Introduction 5
Before YouStart 5
Overview 5
Front View 5
Back View 7
Package Contents 8
Installation 9
Connect Cables 9
Install the Sliding Rack Rails and Cable Management Arm 9
Install the Bezel 10
Configure the Operating System 11
Log into Windows 10 for the First Time 11
Log into Windows Server for the First Time 12
Activate the ACC Software and Connect to Avigilon Cloud Services 13
Activate ACC Software and Feature Licenses 13
Connect to Avigilon Cloud Services 13
Reactivating aLicense 13
Troubleshooting 14
Network Configuration 14
Monitoring System Health 14
Operating System Recovery By Avigilon Recovery Partition 14
Operating System Recovery By External USB 16
Maintenance 17
Checking System Health 17
ACC Client Site Health 17
Server Administrator Software System Health 17
Replacing Hard Drives 18
Guidelines 18
Replacing a Hard Drive Blank 19
Replacing Front or Back Hard Drives 21
LED Indicators 22
Diagnostic Indicators 22
iDRAC Direct LED Indicators 23
Power Status Indicators 23
3
Introduction
The Avigilon Network Video Recorder (NVR5 Standard) is preloaded with Avigilon Control Center (ACC)
software and is configured for exceptional performance and reliability. The Network Video Recorder can be
easily integrated into any existing Avigilon surveillance system or act as the base of a new site.
Before YouStart
Avigilon recommends:
lThe use of an uninterruptible power supply (UPS) system to protect your video surveillance system
hardware. A UPS system is used to protect critical equipment from mains supply problems, including
spikes, voltage dips, fluctuations and complete power failures using a dedicated battery. It can also be
used to power equipment during the time it takes for a standby generator to be started and
synchronized.
If possible, the UPS connection should include configuration to shut down the operating system on the
appliance when battery power is low or there is 15 minutes of power remaining.
lCameras should not be connected to the appliance until after the appropriate network configuration
has been set up.
Overview
Front View
Figure 1: Front view of NVR5 Standard 16TB - 64TB recorder with front bezel installed
Introduction 5
Figure 2: Front view of NVR5 Standard 16TB - 64TB recorder with front bezel removed
1. Bezel
Protects against unauthorized physical access to the hard drives.
For more information, see Install the Bezel on page10.
2. Power button
Controls the power supply to the recorder.
3. Video connector
Accepts a VGA monitor connection.
4. USB 2.0 port
Accepts USB connectors to external devices.
5. iDRAC Direct micro USB port and iDRAC Direct LED indicator
Connects a laptop or desktop computer on the same network as the Integrated Dell™ Remote Access
Controller (iDRAC) version 9.
For more information about the iDRAC web interface, see the information tag on your recorder and the
Enabling iDRAC Enterprise Features Setup Guide (link).
6. Diagnostic indicators
Provides information about system operations.
For more information about the above LED indicators, see LED Indicators on page22.
7. System health and system identification button
Displays the system health. Also identifies a recorder deployed in a rack with other equipment.
For more information, see System Health and Identification Modes on page26.
8. Ten (10) Hard drives
Provides access to hot-swappable hard drives. There are LED indicators on each hard drive.
Some drives may contain an empty hard drive tray.
9. Information tag (top and bottom views are not shown)
Slides out to provide the serial number, system information, and iDRAC account credentials for initial
login to the iDRAC web interface.
Front View 6
Back View
Figure 3: Back view of NVR5 Standard 16TB - 64TB recorder
1. Two (2) 1 Gbps Ethernet ports
Accepts Ethernet connections to multiple networks and includes LEDindicators of the connections.
2. Out-of-Band Management (OOBM) port
Accepts an OOBM RJ-45 connection and includes an LEDindicator of the connection.
3. Keyboard port and mouse port
Accepts connectors to a keyboard and mouse.
4. Video connector
Accepts a VGA monitor connection.
5. Power supply connector
Accepts a power supply connection.
6. Four (4) 1 Gbps Ethernet ports
Accepts Ethernet connections to multiple networks and includes LEDindicators of the connections.
7. System identification button
Identifies a recorder deployed in a rack with other equipment. Also resets the iDRAC web interface
without rebooting the operating system.
For more information about the iDRAC reset, see the Enabling iDRAC Enterprise Features Setup
Guide (link).
For more information about the above LED indicators, see LED Indicators on page22.
Back View 7
Package Contents
Ensure the package contains the following:
lAvigilon NVR5 Standard Recorder
lRack sliding rail assembly kit
lCable management arm assembly kit
lBezel and key
lPower cables
lC13 / C14
lRegion specific
NA: NEMA 5-15P / C13
UK: BS 1363 / C13
EU: SCHUKO / C13
AU: AS3112 / C13
Package Contents 8
Installation
Connect Cables
Refer to the diagrams in the Overview section for the location of the different connectors. Make the following
connections as required:
1. Connect a KVM switch or separate keyboard, mouse and monitor to the recorder.
lThe keyboard and mouse can be connected to any USB port on the recorder.
lThe monitor can be connected to any video connector at the front or back of the recorder.
2. Connect the recorder to your network by plugging an Ethernet cable into one of the Ethernet ports.
3. For out-of-band management access and functionality, connect Ethernet cable to the OOBM
connector.
4. Connect a power cable to each power supply at the back of the recorder.
5. Press the power button on the front of the recorder. Check that the recorder LED indicators display the
correct status. For more information on the different LED status indicators, see LED Indicators on
page22.
Install the Sliding Rack Rails and Cable Management Arm
If the recorder will be mounted in a server rack, install the Sliding Rack Rails and the Cable Management Arm
(CMA) provided in the recorder package. Follow the procedures outlined in the Rack Installation Instructions
and the CMA Installation Instructions provided in the assembly kits.
Note: When rack-mounting the recorder, ensure no interference occurs from the sliding arms of
adjacent equipment in the rack. Every sliding rack rail on the server rack must be aligned before you
insert the recorder into the rail for a smooth installation. For more information, refer to the
dimensions in your server rack design documentation.
Installation 9
Install the Bezel
The bezel can be installed on the front of the recorder to help protect the hard drives against unauthorized
access.
1. Align and insert the right end of the bezel until it clicks into place.
2. Push the left end of the bezel into the front of the unit until it clicks into place.
Install the Bezel 10
Este manual sirve para los siguientes modelos
18
Tabla de contenidos
Otros manuales de Servidor de Avigilon
