Avid CNC PRO4848 Manual de usuario

PRO4848 CNC 4' x 4'

Assembly Instructions

v2018Q4.3, 16.1 Model Revision

PRO Series 4848 Assembly CONTENTS

Contents

1 Base Assembly 3

1.1 Table Leg Assembly ................................ 4

1.2 Table Frame Assembly ............................... 25

1.3 Crossmember Installation ............................. 41

1.4 Linear Rail Installation ............................... 50

1.5 Gear Rack Installation ............................... 63

2 Riser Assembly 70

2.1 Linear Bearing Block Installation ......................... 71

2.2 Table Bumpers .................................... 78

2.3 Risers ......................................... 85

3 Gantry Assembly 99

3.1 Gantry Extrusion Installation ............................ 100

3.2 Gantry Gear Rack Installation .......................... 116

3.3 Linear Rail Installation ............................... 121

3.4 Gantry Bumper Installation ............................ 132

3.5 Gantry Carriage Installation ........................... 138

4 Rack and Pinion Drive Installation 147

4.1 NEMA 23 Drive Assembly ............................. 148

4.2 NEMA 34 Drive Assembly ............................. 163

4.3 R&P Drive Installation ................................ 178

5 Z-Axis Assembly 193

6 Cable Track Assembly 211

7 Motor and Sensor Connections 239

PRO Series 4848 Assembly

Version 2018Q4.1

PRO4848 CNC

Assembly Instructions

16.1 Model Revision

Version 2018Q4.3

PRO Series 4848 Assembly

Base Assembly

PRO Series 4848 Assembly

Version 2018Q4.1

PRO4848 CNC

Assembly Instructions

16.1 Model Revision

Version 2018Q4.3

PRO Series 4848 Assembly 1.1. TABLE LEG ASSEMBLY

1.1 Table Leg Assembly

Note: Skip this section if you did not purchase a Leg Kit.

Note: The Electronics Mounting Bar was added with the 2016Q4.1 revision of our

leg kit. If you purchased the previous revision, please contact us if you wish to up-

grade your leg kit. To assemble without the electronics mounting bar, please refer

to the Leg Kit revision 2016Q3.1 Assembly Diagram at http://www.cncrouterparts.com/leg-

kit-assembly-instructions-p-295.html

The following parts and bags will be used in this section:

•(4) 4080 Leg Extrusion, 750 mm

•(2) 4080 Leg Extrusion, 1250 mm

•(1) 4080 Leg Extrusion, 1440 mm

•(28) 40 Series Anchor Fastener

•(36) M8 x 30mm Socket Head Cap Screw

•(60) M8 Roll in T-Nut

•(4) 7111 Foot Plate

•(4) H172 Leveling Foot

•(8) CRP813-01 Leg Kit Gusset

•(32) M8 x 14mm Hex Cap Bolt

PRO Series 4848 Assembly

Version 2018Q4.1

PRO4848 CNC

Assembly Instructions

16.1 Model Revision

Version 2018Q4.3

PRO Series 4848 Assembly 1.1. TABLE LEG ASSEMBLY

M8 x 30mm Socket Head Cap Screw

M8 Roll In T-Nut

4080 Leg Extrusion, 1250mm

•Thread the socket head cap screws into the t-nuts through the anchor fasteners

as indicated.

PRO Series 4848 Assembly

Version 2018Q4.1

PRO4848 CNC

Assembly Instructions

16.1 Model Revision

Version 2018Q4.3

PRO Series 4848 Assembly 1.1. TABLE LEG ASSEMBLY

•Slide the anchor assembly into the extrusion.

PRO Series 4848 Assembly

Version 2018Q4.1

PRO4848 CNC

Assembly Instructions

16.1 Model Revision

Version 2018Q4.3

PRO Series 4848 Assembly 1.1. TABLE LEG ASSEMBLY

•Repeat the previous steps on both sides for each of the 1250mm Leg extrusion

sections.

PRO Series 4848 Assembly

Version 2018Q4.1

PRO4848 CNC

Assembly Instructions

16.1 Model Revision

Version 2018Q4.3

PRO Series 4848 Assembly 1.1. TABLE LEG ASSEMBLY

4080 Leg Extrusion, 750 mm

•Repeat the previous steps one side for each of the 750mm Leg extrusion sections.

PRO Series 4848 Assembly

Version 2018Q4.1

PRO4848 CNC

Assembly Instructions

16.1 Model Revision

Version 2018Q4.3

PRO Series 4848 Assembly 1.1. TABLE LEG ASSEMBLY

H172 Leveling Foot

M8 x 30mm Socket Head Cap Screw M16 Hex Nut

7111 Foot Plate

4080 Leg Extrusion, 750 mm

•Install a foot assembly onto a piece of 750mm Leg extrusion as indicated.

PRO Series 4848 Assembly

Version 2018Q4.1

PRO4848 CNC

Assembly Instructions

16.1 Model Revision

Version 2018Q4.3

PRO Series 4848 Assembly 1.1. TABLE LEG ASSEMBLY

•Fully tighten the highlighted fasteners.

PRO Series 4848 Assembly

Version 2018Q4.1

PRO4848 CNC

Assembly Instructions

16.1 Model Revision

Version 2018Q4.3

Tabla de contenidos

Manuales populares de Fresadora de madera de otras marcas

Stanley

Stanley SRR1200-RU Manual de usuario

Wolfcraft

Wolfcraft MASTER RT 540 Manual de usuario

Worx Professional

Worx Professional WU600 Manual de usuario

Proxxon

Proxxon BFW 40/E Manual de usuario

Porter-Cable

Porter-Cable 893PK Manual de usuario

Ryobi

Ryobi R181D Manual de usuario

Clarke

Clarke Contractor CR3 Manual de instrucciones

Vision Engraving & Routing Systems

Vision Engraving & Routing Systems 1624R Manual de usuario

Triton

Triton TMNRTR Instrucciones de montaje

Status

Status RH1800 Manual de usuario

Asist

Asist AE4F120DN Manual de usuario

Sealey

Sealey SV20 Series Manual de usuario

Makita

Makita 3606 Manual de usuario

RIDGID

RIDGID R2901 Manual de usuario

Hitachi Koki

Hitachi Koki M 12V2 Manual de usuario

Promaker

Promaker PRO-RT1600 Manual de usuario

Wen

Wen RT1460 Manual de usuario

Mafell

Mafell LO 50 E Guía