Avery Dennison Monarch 9855 Manual de usuario

QUICK REFERENCE

This Quick Reference contains supply loading and general

care and maintenance procedures for the Monarch9855

printer. For more detailed information, refer to the

Operator’s Handbook available on our Web site

(www.monarch.com). For information about creating

formats, configuring the printer, or programming the

printer, refer to the Packet Reference Manual available on

our Web site.

Note: Information in this document supercedes

information in previous versions. Check our Web

site for the latest documentation and release

information.

Connecting the Cables

The power supply automatically switches between 115V or

230V. There are no operator settings required.

1. Review the safety information in the Regulatory

Compliance document included with your printer.

2. Plug the power cable into the socket. Plug the other

end of the cable into a grounded

electrical outlet.

3. Connect the communication cable into the

appropriate port. Secure the cable with

the connecting screws (serial) or

spring clips (parallel).

If you are communicating with the

host through the serial port, make

sure the printer's communication

values match those at the host.

Parallel Port

Power Cable Goes Here

Serial Port

USB Port

Monarchand 9855are registered trademarks of Avery

Dennison Retail Information Services LLC. Avery

Dennisonis a trademark of Avery Dennison Corp.

The factory default values are 9600 Baud, no

parity, 8 bit data frame, 1 stop bit, and DTR flow

control (9600, N, 8, 1, DTR).

Set the communication values on the printer to

match those at the host.

The printer also has a USB (Universal Serial Bus)

version 2.0 communications port, which is

compatible with version 1.1. Drivers are available

on our Web site for a variety of operating systems.

4. Turn on the printer. Press ( I ) to turn on and ( O ) to

turn off the printer.

Using the Control Panel

The control panel has a two-line LCD

display, two status lights, and five

buttons. The control panel displays

error codes/messages, and allows

you to setup/configure the printer.

Power: The printer shows a

steady green light

when it is on.

Fault: The printer shows a

steady amber light

when it is out of labels or ribbon, or when you

have a supply jam.

Feed/

Cut:

Prints a label in the on-demand mode, feeds a

blank label if there is no print job, prints a

label with error information that is useful to

your System Administrator if an error is

displayed, cuts the supply when pressed and

held for two seconds if a knife is installed.

Enter/

Pause:

Pauses the current print job or resumes a

paused print job. Selects the displayed menu

item.

Escape/

Clear:

When an error is present, clears the error.

When a job (batch) is printing, cancels the

print job (batch). Enters the offline menu mode

or returns the display to the next higher menu.

ÅDisplays the previous menu item.

ÆDisplays the next menu item.

Åand ÆPrints a test label when you press the buttons

at the same time. Hold for one second and

release.

Loading Labels or Tags

1. Open the cover.

2. Unlock the printhead by turning the retaining latch.

3. Lift printhead assembly using the printhead tab until

the assembly locks into place.

Printhead

Tab

Deflector

Tab

4. Place the roll of supply on the supply holder. For

labels, the supply unrolls from the top or the bottom.

For tags, make sure the supply unrolls from the

bottom, because tag rolls are wound face in. Do not

pick up the printer by the supply holder.

5. Adjust the supply holder guides so the sides barely

touch the roll. Make sure the supply roll turns freely.

If you are using fan-fold supplies, place the supply

stack behind the printer, label side facing up.

Supply Lever

Supply

Holder

Guides

6. Push down on the supply lever to unlock the supply

guides.

7. Lay the label strip across the supply guide so that a

few inches extend past the front of the printer. Tuck

the supply under the nibs and in between the die cut

sensor.

For fan-fold supplies, lay the label strip over the

supply holder and across the supply guide so that

a few inches extend past the front of the printer.

Tuck the supply under the nibs and in between the

die cut sensor.

For tag supplies using the optional knife, feed

the supply through the knife. Make sure at least

0.5 inches of supply is past the knife.

8. Adjust the supply guides so they touch the supply.

Push up on the supply lever to lock the supply guides

into place.

9. Hold the printhead assembly by the printhead tab while

pressing down on the printhead release.

Supply

Lever

Nibs

Die Cut Sensor

10. Close the mb

well until you

12.

to properly position the supply and the

1. ls from the first 10 inches of the

backing paper.

printhead by pressing down on the thu

hear it click into place.

11. Close the cover.

Press Feed/Cut several times to feed at least three

labels/tags

ribbon.

Loading Labels for the Optional Peel Mode

Peel mode must be purchased separately. In peel mode

the printer separates the backing paper from the label.

The next label is not printed until the completed one is

removed from the printer. Make sure the printer is

configured for on-demand mode and the correct suppl

type. The minimum feed length is 1.5 inches for pee

mode. Hold the leading edge of peeled labels when

printing on stock longer than six inches.

You must use non-perforated supplies for peel mode.

Follow the steps for loading supplies from the previous

section. Then, follow these steps after you close the

pr thead.

Remove the labe

2. Press down on the exit cover tabs to open the exit

cover on the front of the printer.

3. Feed the backing paper over the peel bar.

Lower

Opening

Peel

Bar

4. Feed the backing paper through the lower opening of

the exit cover. Close the exit cover. Pull down on the

backing paper to remove any slack.

Tear

Edge

Backing

Paper

When removing the backing paper, pull up

across the saw-toothed tear edge. Make sure

the backing paper tears at the edge.

5. Close the printer's cover.

6. Press Feed/Cut several times to feed at least three

labels/tags to properly position the supply and the

ribbon.

To load and use linerless or string tag supplies, refer to

the Operator’s Handbook.

Adjusting the Wide/Narrow Knobs

You may need to adjust the two wide/narrow knobs

according to the width of your supply. For supply that is

more than two inches, adjust the knobs to the wide setting.

For supply that is two inches or less, adjust the knobs to

the narrow setting. For linerless supply, use the narrow

setting (knobs are up). For string tag supplies, use the

wide setting (knobs are down).

You must adjust both of the knobs to the same position. If

you experience ribbon smudging in cold, dry environments,

adjust the wide/narrow knobs to the wide setting.

For wide supplies, push down and turn the wide/narrow

knobs clockwise with a screwdriver.

For narrow supplies, turn the wide/narrow knobs counter-

clockwise with a screwdriver until it pops back up.

The adjustment is shown in the wide position.

Wide/Narrow Knobs

Loading Ribbon

1. Open the cover.

2. Unlock the printhead by turning the retaining latch.

3. Lift printhead assembly using the printhead tab until

the assembly locks into place.

4. Push the deflector tab down.

Deflector

Tab

5. Slide the extra ribbon core on the take-up reel as far

as it will go with the "This End Out" writing facing out.

Use your empty ribbon core as the take-up core. The

take-up core only fits on the take-up reel one way.

6. Remove the new ribbon from the package. Do not

wrinkle or crush the new ribbon.

7. Slide the ribbon onto the back reel as far as it will go.

Carefully unwind a few inches of ribbon from the

bottom of the roll.

Take-up Core

Take-up Reel

Ribbon

Rollers

Note: Make sure the “Monarch This End Out” writing is

facing out. The ribbon roll only fits on the reel one

way.

8. Carefully feed the ribbon under both ribbon rollers and

printhead.

9. Align the ribbon and make sure it is straight and

centered throughout the path.

10. Tape the ribbon to the take-up core. Do not tape the

ribbon to the take-up reel.

11. Rotate the take-up core until the leader is past the

printhead.

12. Remove any slack in the ribbon by turning the take-up

reel clockwise.

13. Hold the printhead assembly by the printhead tab while

pressing down on the printhead release.

14. Close the printhead by pressing down on the thumb

well until you hear it click into place. Close the cover.

15. Press Feed/Cut several times to feed at least three

labels/tags to properly position the supply and the

ribbon.

Clearing Jams

When you are printing and a jam occurs, the Fault light on

the printer's front panel blinks.

1. Turn off the printer and open the cover and printhead

assembly.

2. If necessary, remove the label roll and ribbon.

3. Remove the jammed labels and reload the label roll.

4. Close the printhead assembly and turn on the printer.

5. Press Feed/Cut several times to feed at least three

labels/tags to properly position the supply and the

ribbon.

Otros manuales para Monarch 9855

Tabla de contenidos

Otros manuales de Lector de código de barras de Avery Dennison

Avery Dennison

Avery Dennison TTX 350 Manual de usuario

Avery Dennison

Avery Dennison TTX 350 Manual de usuario

Avery Dennison

Avery Dennison Monarch 938 Manual de usuario

Avery Dennison

Avery Dennison Monarch Pathfinder Ultra Manual de servicio

Avery Dennison

Avery Dennison Pathfinder 6057 Guía del usuario

Avery Dennison

Avery Dennison Monarch 9855 Guía

Avery Dennison

Avery Dennison Monarch Pathfinder Ultra Silver 6032 Manual de usuario

Avery Dennison

Avery Dennison AP5.4 Guía de solución de problemas

Avery Dennison

Avery Dennison Monarch Pathfinder 6059 Manual de servicio

Avery Dennison

Avery Dennison Monarch SIERRA SPORT4 9493 Manual de uso y cuidado

Manuales populares de Lector de código de barras de otras marcas

POSMicro

POSMicro Datalogic PowerScan D7100 Manual de usuario

Marson

Marson MT780 Guía de configuración rápida

NCR

NCR RealPOS Manual de usuario

Motorola

Motorola SE3300 Guía de configuración rápida

Element

Element P130BT Manual de usuario

Motorola

Motorola Symbol LS3008 Manual de instalación y operación

Meec tools

Meec tools OBD-II / VAG Manual de usuario

SICK

SICK CLP 100 Manual de usuario

Royal Tag SA

Royal Tag SA I-Read Manual de usuario

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manual de usuario

Meteor

Meteor 8310 Manual de usuario

Denso

Denso BHT-500B Manual de usuario

Datalogic

Datalogic Heron HD3130 Manual de usuario

Motorola

Motorola MP6000 Instrucciones de montaje

Newland

Newland NLS-HR15-BT Manual de usuario

ARTDEV

ARTDEV AS-1310 Manual de usuario

Aopos

Aopos AS290 Manual de usuario

ENS

ENS 367-5455 Manual de usuario