Avaya S8500 Series Manual de usuario

555-245-760 Issue 3 January 2005 1

Replacing the S8500 dual network interface

This section describes the steps required to replace an existing dual network interface card

(NIC) on the S8500 and S8500B Media Servers. The control network traffic from the server out

to the dedicated customer LAN travels through the NIC.

Note:

Note: This procedure applies to both S8500B and S8500 media servers. The section

about Installing the new network interface cardhas different procedures for

S8500B and S8500.

The components of this procedure include:

●Backing up the media server

●Powering down the media server

●Removing the cover of the media server

●Removing the fan unit

●Removing the old network interface card

●Installing the new network interface card

●Replacing the fan unit

●Replacing the cover and cabling

●Powering up the server

●Checking LED activity on the dual network interface card

●Confirming original Ethernet configuration

!CAUTION:

CAUTION: Wear an antistatic wrist ground strap whenever handling the media server or its

components. Connect the strap to an approved ground, such as an unpainted

metal surface.

Backing up the media server

Backup the media server before you power it down. To backup the media server complete the

following steps:

1. Connect the services laptop to the port labeled 2 (Eth 1) on the back of the media server

using the crossover cable.

2. Open a browser window on the laptop.

Replacing the S8500 dual network interface

2 Replacing the S8500 dual network interface

3. In the address field of the browser, type in the URL for the media server and press Enter.

A welcome window opens (Figure 1: Welcome Window on page 2).

Figure 1: Welcome Window

4. Click Continue.

5. Accept the Avaya certificate by clicking Yes.

The logon window appears (Figure 2: Logon window on page 3).

555-245-760 Issue 3 January 2005 3

Figure 2: Logon window

6. Type craft in the Logon ID field and the password (obtained from ART) in the Password

field and click Logon.

7. Suppress alarm origination by clicking Yes.

8. Click Launch Maintenance Web Interface.

9. Select Data Backup/Restore > Backup Now from the navigation pane.

10. Select All data sets under the Data Sets heading.

11. Select one of the following backup methods:

●FTP

●E-mail

●Local PC card

12. If you want to encrypt the backup, select the Encrypt backup using pass phrase check

box and type a pass phrase.

13. Click Start Backup.

Replacing the S8500 dual network interface

4 Replacing the S8500 dual network interface

Powering down the media server

After the backup is finished, complete the following steps to power down the media server.

1. From the media server Web interface click Shutdown This Server.

2. Select Delayed.

3. After the media server shuts down unplug the power cord from the back of the server.

4. Unplug the power cord from the RSA.

5. Disconnect the modem from the RS-232 port on the RSA.

6. Disconnect and label the LAN connection (if used) from the Ethernet port on the RSA.

7. Pull the server forward so that the server rails expand and the retaining clips on the rails

click into place.

8. Unplug and label the cable from the Ethernet port labeled LINK A on the dual NIC.

Removing the cover of the media server

!CAUTION:

CAUTION: Remove all power from the media server before starting this procedure.

To remove the cover of the media server:

1. Loosen the two captive screws on the back of the media server (see Figure 3: Locating the

server cover’s captive screws on page 5.

2. Slide the server cover back from the front panel until the cover’s tabs are released from the

top slot of the front panel.

3. Lift the cover straight up and move it away from the server as shown in Figure 3: Locating

the server cover’s captive screws on page 5.

555-245-760 Issue 3 January 2005 5

Figure 3: Locating the server cover’s captive screws

Removing the fan unit

To remove the fan unit from the media server:

1. Locate the slot labeled PCI-2 on the left hand side of the back of the server under the fan

unit.

2. Remove the two screws holding the fan unit. You do not need to unplug the fan unit.

3. Set the adapter-support bracket to the right of the fan.

Figure notes:

1. Server cover’s captive screws

h3mscaps LAO 070103

disc

Replacing the S8500 dual network interface

6 Replacing the S8500 dual network interface

Removing the old network interface card

To remove the old NIC:

1. Completely unscrew the captive screw on the left hand side of the PCI-2 slot.

The captive screw is now loose so that you can flip it up. You will need this space to

maneuver the old NIC out of its slot.

2. Firmly pull the card out of its slot.

Installing the new network interface card

Depending on the S8500 server model, use one of the following procedures:

●Installing the new network interface card in the S8500B media server

●Installing the new network interface card in the S8500 Media Server

Installing the new network interface card in the S8500B media server

Note:

Note: The procedure is for S8500B.

Note:

Note: Wear an antistatic wrist ground strap whenever handling the media server or its

components. Connect the strap to an approved ground, such as an unpainted

metal surface. See the job aid titled Approved Grounds for more information.

To install the network interface card (NIC):

1. Carefully grasp the new NIC by the top edge or upper corners and align it with the PCI-2

expansion slot on the motherboard. (The SAMP is connected on the other side of this

connector.) Press the NIC firmly into the expansion slot. See Figure 4: Inserting the

network interface card on page 7.

555-245-760 Issue 3 January 2005 7

Figure 4: Inserting the network interface card

!CAUTION:

CAUTION: Be sure that the NIC is completely and correctly seated in the PCI-2 expansion

slot of the Avaya S8500B Media Server. Incomplete insertion might cause

damage to the system board or the NIC.

2. Position the faceplate so that it fits in the PCI-2 slot using the captive screw to hold it in

place.

3. Tighten the captive screw.

Installing the new network interface card in the S8500 Media Server

Note:

Note: This procedure is for S8500.

To install the new NIC into the S8500 media server:

1. Carefully grasp the new NIC by the top edge or upper corners and align it with the PCI-2

expansion slot (see Figure 5: Inserting the new network interface card on page 8). Press

the NIC firmly into the expansion slot.

Ensure that the NIC is completely and correctly seated in the PCI-2 expansion slot of the

S8500 Media Server. Incomplete insertion might cause damage to the system board or the

NIC.

2. Position the faceplate so that it fits in the PCI-2 slot using the captive screw to hold it in

place.

indsbnic KLC 101404

Replacing the S8500 dual network interface

8 Replacing the S8500 dual network interface

Figure 5: Inserting the new network interface card

Replacing the fan unit

To replace the fan unit in the media server:

1. Replace the fan unit with the fan blades pointed down toward the NIC, securing the fan unit

with the two original screws.

Figure notes:

1. Mounting screws 3. Network interface card

2. Fan assembly 4. Smaller faceplate

PCI

PCI 2

100-127-,3,0A,50/60Hz

200-240-,1,5A,50/60Hz

133MHz/64Bit, 100MHz/64Bit

h3ms2nic KLC 031004

555-245-760 Issue 3 January 2005 9

Replacing the cover and cabling

To replace the cover and cabling on the media server:

1. Replace the cover onto the server.

2. Slide the cover forward so the cover’s tabs slide into place under the top slots of the front

panel.

3. Finger-tighten the thumb screws on the back of the server.

4. Release the retaining tabs on the rails and slide the S8500 Media Server back into place on

the data rack.

5. Locate the marked cable that you removed from the old NIC and plug it into the Ethernet 2

port, which is labeled “ACT/LINK A” on the small faceplate of the new NIC.

6. Connect all external cables.

Powering up the server

To power up the media server:

1. Plug the power cord into the power receptacle on back of the server.

2. Press the Power button located on the front right-hand side.

3. Log in to the server after the startup to ensure that the installation is complete.

Checking LED activity on the dual network interface card

When the media server is back in service, check the LEDs on each port of the dual NIC

(Figure 6: S8500 rear panel dual NIC LEDs on page 10).

Replacing the S8500 dual network interface

10 Replacing the S8500 dual network interface

Figure 6: S8500 rear panel dual NIC LEDs

Confirming original Ethernet configuration

After the media server is back in service, check the original Ethernet configuration settings:

1. Go to Server Configuration > Configure Server Web page.

2. Confirm that the server’s Ethernet configuration settings are the same as before.

Configuring the NIC

To configure the new NIC:

1. At the Web interface select Server Configuration > Configure Server.

2. Click Continue through the review notices until you get to the xxx page.

3. Select Configure Individual Services and click Continue.

4. Select Set Identities and click Continue.

5. The following Ethernet ports are listed:

●Control Network A: [default: Ethernet 0]

●Services Port: [default: Ethernet 1]

●Corporate LAN: [default: Ethernet 0]

Figure notes:

1. Network activity LED

(Tx/Rx)

2. Connection rate:

●LED is off: there is a 10 BASE-T active link.

●LED is green: there is a 100 BASE-T active link.

●LED is orange: there is a 1000 BASE-T active link.

1 2

LINK TX/RX LINK TX/RX

PCI

PCI 2

100-127 -, 3,0A, 50/60 Hz

200-240 -, 1,5A, 50/60 Hz

133 MHz/64 Bit, 100 MHz/64 Bit

h3msble2 KLC 082503

100-127 -, 3,0A,

200-240 -, 1,5A, 5

Otros manuales para S8500 Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Servidor de Avaya

Avaya

Avaya S8510 Manual de usuario

Avaya

Avaya AG250 Manual

Avaya

Avaya Definity Enterprise Communications Server Manual de usuario

Avaya

Avaya S8500 Series Manual de usuario

Avaya

Avaya Meridian 1 Series Guía de inicio rápido

Avaya

Avaya CS 1000 Guía

Avaya

Avaya G650 Manual de usuario

Avaya

Avaya Configuring Avaya IP Office R8.0 Suplemento

Avaya

Avaya Converged Platform 130 Series Manual de instrucciones

Avaya

Avaya S8700-Series Manual de instrucciones

Avaya

Avaya callpilot 1002rp Manual

Avaya

Avaya S6200 Manual de instrucciones

Avaya

Avaya S8300 Series Manual de usuario

Avaya

Avaya Scopia XT5000 Manual de usuario

Avaya

Avaya QuesCom 400 Guía

Avaya

Avaya 8200 Manual de instrucciones

Avaya

Avaya 1000 Series Guía

Avaya

Avaya 1000 Series Manual de servicio

Avaya

Avaya Media Processing Server 500 Manual de instrucciones

Avaya

Avaya Communication Server 1000M Single Group Manual de usuario

Avaya

Avaya Definity G3 / ProLogix Guía de inicio rápido

Avaya

Avaya Definity Enterprise Communications Server Manual de usuario

Avaya

Avaya S8730 Manual de instrucciones

Avaya

Avaya S8700 Series Manual de instrucciones

Manuales populares de Servidor de otras marcas

HP AlphaServer ES47 Manual de usuario

Dell

Dell PowerEdge R410 Manual de usuario

PowerNAS

PowerNAS CMA Manual de usuario

Supero

Supero FatTwin F617R3-FT Manual de usuario

MSI

MSI P1-109N-L70 Manual de usuario

Dell

Dell PowerEdge XE9640 Manual

Dell

Dell PS4100 Instrucciones de montaje

EtroVISION

EtroVISION EV3151 Manual de usuario

NEC

NEC Express5800/T110j Manual de usuario

HP ProLiant Gen9 Manual de usuario

Compaq

Compaq ProLiant 3000 Manual

Dell

Dell PowerEdge 3YPMN Manual de usuario

iRobo

iRobo IPC2U Manual de usuario

Nortel

Nortel 1000 Con?guration guide Manual de usuario

Asus

Asus AP7500 Manual de operación y mantenimiento

Avid Technology

Avid Technology AirSpeed 5000 Manual de usuario

HP Integrity rx2600 Guía de instalación

Milestone

Milestone Husky IVO 350T Manual de usuario