Avantes AvaLight-LED Hoja de especificaciones

NEED TECHNICAL SUPPORT?

Scan the QR-code or visit www.avantes.com/support

We are happy to help you!

AVALIGHT-LED

LIGHT SOURCES

Operation and Installation Manual

ID: 020405

Revision: 1-00

www.avantes.com

[email protected]om

This document is protected by copyright. Do not copy or publish this document or parts of it without

written permission of Avantes BV.

Product specifications and descriptions in this manual are subject to change without notice. Avantes

BV will not be responsible for errors and omissions in this manual or for direct or incidental damages

in connection with the use of this device or information.

Oude Apeldoornseweg 28

7333 NS Apeldoorn

The Netherlands

Phone: +31 313 670 170

Website: http://www.avantes.com

E-Mail: info@avantes.com

ID: 020405

Revision: 1-00

www.avantes.com

[email protected]om

Table of Content

1. Introduction ......................................................................................................3

2. AvaLight-LED .....................................................................................................4

2.1 Quick start ..................................................................................................4

2.2 12VDC Power plug .........................................................................................5

2.3 Settings for the Pulsed Mode ............................................................................5

3. AvaLight-LED-CON ...............................................................................................6

3.1 Quick start ..................................................................................................6

3.2 12VDC Power plug .........................................................................................7

3.3 Settings for the Pulsed Mode ............................................................................7

4. Changing the LED of the AvaLight-LED.......................................................................8

5. Technical support................................................................................................9

5.1 Getting Help................................................................................................9

5.2 AvaSoft Updates ...........................................................................................9

6. Specifications................................................................................................... 10

6.1 Ordering Information ................................................................................... 10

7. Appendix A...................................................................................................... 11

ID: 020405

Revision: 1-00

www.avantes.com

[email protected]om

1. Introduction

Thank you for purchasing the Avantes AvaLight-LED-(CON). This light source will provide outstanding

performance. To get the best of its performance it perfectly matches all Avantes AvaSpec

spectrometers.

The AvaLight-LED works from the UV light to the near infrared, it depends on the choice of the

wavelength for the LED.

The AvaLight-LED-CON is a LED control unit with a connector to a LED. The AvaLight-LED-CON works

in combination with the CUV-LED-XXX, where XXX represents the wavelength of the LED.

The AvaLight-LED-CON in combination with the CUV-LED-XXX makes it possible to place the LED

directly into your application, to avoid the transmission losses from the optical fiber.

The AvaLight-LED-(CON) can operate in a continuous mode or in a pulse width mode.

ID: 020405

Revision: 1-00

www.avantes.com

[email protected]om

2. AvaLight-LED

2.1 Quick start

Power LED

The green LED act as status LED for the light source when the power is turned on.

OFF-TTL-ON Switch

Choose operating mode with the mode-switch:

Switch position

PWM signal

Light source

LED

OFF

TTL

Not connected

OFF

High

Low

OFF

SMA-plug

Connect the SMA connector of the fiber to the SMA-plug of the Light Source.

OFF-TTL-ON

switch

Power LED

SMA-plug

12VDC Power

plug

I/O connector

ID: 020405

Revision: 1-00

www.avantes.com

[email protected]om

I/O connector

For PWM mode to be controlled by software it is needed to connect an AvaSpec spectrometer to the

AvaLight-LED with the interface cable IC-DB26-2. Now it is possible to control the output operation

mode by software (AvaSoft).

The signals on the I/O connector are described below.

Pin configuration

Name

Description

PWM

Input

Input, used the PWM

GND

Ground

Below the electrical characteristics for the input signals.

Electrical characteristics

Name

Low level detection

High level detection

Maximum voltage

PWM

< 0.7V

> 0.7V

5.0V

2.2 12VDC Power plug

The power supply specifications are mentioned in the table below

Name

Minimum

Typical

Maximum

Voltage

10V

12V

15V

Power

0.5Watt

2.3 Settings for the PWM Mode

When the light source is used in combination with an AvaSpec spectrometer, interface cable IC-

DB26-2 and AvaSoft, the optical output can be changed by using the PWM function in AvaSoft.

See appendix A for how to set the PWM signal in AvaSoft.

The PWM can be set in a range from 500 Hz –300 KHz with a 0 –100% duty cycle.

ID: 020405

Revision: 1-00

www.avantes.com

[email protected]om

3. AvaLight-LED-CON

3.1 Quick start

Power LED

The green LED act as status LED for the light source when the power is turned on.

OFF-TTL-ON Switch

Choose operating mode with the mode-switch:

Switch position

PWM signal

Light source

LED

OFF

TTL

Not connected

OFF

High

Low

OFF

LED connector

Connect the CUV-LED-XXX to this connector or place your own made LED cable based on the

information below:

Connector type: Binder 719, 3 pole (09 9747 70 03)

Pin number

Function

Cathode

N/C

Anode

OFF-TTL-ON

switch

Power LED

LED connector

12VDC Power

plug

I/O connector

ID: 020405

Revision: 1-00

www.avantes.com

[email protected]om

I/O connector

For PWM mode to be controlled by software it is needed to connect an AvaSpec spectrometer to the

AvaLight-LED with the interface cable IC-DB26-2. Now it is possible to control the output operation

mode by software (AvaSoft).

The signals on the I/O connector are described below.

Pin configuration

Name

Description

PWM

Input

Input, used the PWM

GND

Ground

Below the electrical characteristics for the input signals.

Electrical characteristics

Name

Low level detection

High level detection

Maximum voltage

PWM

< 0.7V

> 0.7V

5.0V

3.2 12VDC Power plug

The power supply specifications are mentioned in the table below

Name

Minimum

Typical

Maximum

Voltage

10V

12V

15V

Power

0.5Watt

3.3 Settings for the PWM Mode

When the light source is used in combination with an AvaSpec spectrometer, interface cable IC-

DB26-2 and AvaSoft, the optical output can be changed by using the PWM function in AvaSoft.

See appendix A for how to set the PWM signal in AvaSoft.

The PWM can be set in a range from 500 Hz –300 KHz with a 0 –100% duty cycle.

ID: 020405

Revision: 1-00

www.avantes.com

[email protected]om

4. Changing the LED of the AvaLight-LED

1. Disconnect the power connector from the socket.

2. Remove the screw protection caps on the front side.

3. Remove the screws with the torx screwdriver (Torx T10)

4. Remove the Hex UNC screws of the DB15 connector from the back side.

5. Take out the front plate and electronics board.

6. Untighten the screws from the LED holder and LED connector.

7. Slightly bend the electrical wires out of the LED connector.

8. Take out the LED from the LED holder.

9. Replace the LED, make sure the Anode and Cathode are connected in the same way and LED

legs make no short circuit. Extension of the legs may be needed depending on the LED type.

10. Tighten the screws from the LED holder and LED connector.

11. Put back the electronics board and front plate back into the housing.

12. Put back the hex UNC screws and the screws in the front plate.

13. Put back the protection caps on the front side.

14. Apply power to see if the LED is illuminating.

Anode

Cathode

ID: 020405

Revision: 1-00

www.avantes.com

[email protected]om

5. Technical support

5.1 Getting Help

If you have any questions, comments or requests concerning your AvaLight-LED-(CON) or the AvaSoft

software, please go to: http://www.avantes.com

In case you have any questions or need support, please send us an email via [email protected]

5.2 AvaSoft Updates

To check for updates, you can choose “Check for Updates” from the Help menu or go to the

“Support” section on our website www.avantes.com.

Tabla de contenidos

Otros manuales de Equipo de iluminación de Avantes

Avantes

Avantes AvaLight-CAL Instrucciones de instalación

Avantes

Avantes AvaLight-Hal-CAL-Mini Manual de usuario

Avantes

Avantes AVASPHERE-50-LS-HAL-12V Hoja de especificaciones

Avantes

Avantes AvaLight HAL Mini Manual de usuario

Avantes

Avantes AvaLight-CAL-MINI Manual de usuario

Avantes

Avantes AVALIGHT-DH-CAL Hoja de especificaciones

Avantes

Avantes AvaLight-XE-HP Hoja de especificaciones

Avantes

Avantes AvaLight-HPLED Manual de usuario

Avantes

Avantes AvaLight-D-S Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario