AV-GAD EasyLoader AV-2005 Manual de usuario

Ea s y L o a d e r

AV-2005 & AV-2008

Integrated Alarm Control/Communicator

Year 2000 ready

Installation and Operation Manual

Version 2.17C

Edition IIII

This product is subject to continuous enhancements and therefore

specifications may be changed or altered without prior notice

Table of Contents

CONTENTS PAGE

SECTION I: SYSTEM FEATURES ................................................................................ 4

1. INTRODUCTION...................................................................................................... 4

1.1  GENERAL DESCRIPTION.................................................................................... 4

1.2  FEATURES......................................................................................................... 5

1.3  PROGRAMMABLE FEATURES............................................................................. 5

1.4  ALARM OUTPUTS ............................................................................................. 5

1.5  TECHNICAL SPECIFICATIONS SERIES 2000........................................................ 7

1.6  ORDERING INFORMATION ................................................................................. 9

SECTION II: INSTALLATION ................................................................................ 10

1. MOUNTING .............................................................................................................. 10

1.1  CONTROL PANEL MOUNTING............................................................................ 10

1.2  ZONE WIRING MODE ........................................................................................ 11

1.3  KEYPAD WIRING .............................................................................................. 13

2. ALARM OUTPUTS................................................................................................... 15

2.1  SIRENS.............................................................................................................. 15

2.2  SIREN CONNECTIONS........................................................................................ 15

2.3  WIRING AND CONNECTION OF RELAY MODULE ............................................... 16

2.4  REMOTE INDICATION ........................................................................................ 16

3. WIRING AND POWERING UP ............................................................................... 17

3.1  GROUNDING – LIGHTNING PROTECTION ........................................................... 17

3.2  BACK UP BATTERY .......................................................................................... 17

3.3  BEFORE POWERING UP..................................................................................... 18

3.4  CONNECTING SMOKE DETECTORS .................................................................... 18

3.5  TELEPHONE SYSTEM (DIALER) DIALING AND WIRING ...................................... 19

3.6  SVM - VOICE MODULE .................................................................................... 19

3.7  REMOTE KEY AND WIRELESS ARMING & DISARMING...................................... 20

3.8  AUTO ARMING ................................................................................................. 20

3.9  ARMING MULTIPLE ALARM PANELS................................................................. 21

SECTION III: AV-701/702 DIGITAL KEYPAD...................................................... 22

1.1  KEYPAD FUNCTIONS......................................................................................... 22

1.2  HOLD-DOWN FUNCTIONS ................................................................................. 24

1.3  AV-2008 GOLDEN; ACCESS VIA CODE............................................................. 29

1.4  SOUNDER.......................................................................................................... 30

1.5  LED INDICATORS ............................................................................................. 31

1.6  KEYPAD DIGITAL DISPLAY (7-SEGMENT TYPE)................................................. 32

1.7  ARMING AND DISARMING................................................................................. 33

SECTION IV: PROGRAMMING ............................................................................. 34

1. SYSTEM CODES ...................................................................................................... 34

1.1  USER CODE PROGRAMMING ............................................................................. 35

2. FEATURE PROGRAMMING AT INSTALLER LEVEL ........................................ 36

2.1  PROGRAMMING SHEET (VERSION 2.17)............................................................. 36

2.2  INTRODUCTION ................................................................................................. 40

2.3  PROGRAMMING SHEET EXPLANATION .............................................................. 40

2.4  GLOSSARY OF PROGRAMMABLE FEATURES ...................................................... 41

2.7  PROGRAMMING EXAMPLES............................................................................... 46

2.8 RESET SYSTEM TO DEFAULT PROGRAMMING ................................................... 50

2.9  DIALER - COMMUNICATOR EXPLANATION AND PROGRAMMING....................... 51

2.9.1  DELETING TELEPHONE NUMBERS.................................................................. 52

2.9.2  USER PROGRAMMING OF ‘FOLLOW-ME’ TELEPHONE NUMBER ..................... 52

2.10  QUITTING PROGRAMMING MODE ................................................................... 53

2.11  VERIFICATION OF CURRENT PROGRAMMING .................................................. 54

2.12  REMOTE UP AND DOWNLOAD ........................................................................ 54

3. TROUBLESHOOTING ............................................................................................. 59

SECTION V: WIRING DIAGRAM .............................................................................. 62

SERIES 2000 AND 860 WIRING DIAGRAM ................................................................... 62

SECTION VI: INDEX.................................................................................................... 63

AV-GAD LIMITED WARRANTY........................................................................... 65

SECTION I: SYSTEM FEATURES

1. INTRODUCTION

1.1  General Description



Av-Gad's EasyLoader TM Series is a microprocessor-based intruder alarm panels with integrated

communicator and modem for up and download. They feature eight or five plus one panic zone, each

programmable.

Series 2000 represent the state-of-the-art in user-friendly, reliable alarm control panels for security

requirements of small and medium-size commercial, residential, and industrial installations.

Read this manual before installing AV-2004, AV-2048 (for further details refer to AV-2004/48

Express Installation Manual).



Av-Gad's EasyLoader TM versatile control panels meet and surpass all requirements for reliability

and maintains. Provide the added benefits of easy installation and simple operation.

 The PRO Version is an upgraded model of the Series 2000 panels, specially designed to be

compatible with AV-707 and AV-706 (English Text) keypads.

 The Series 2000 comprise an enhanced power supply, improved electronics and additional signaling

indicators.

 The innovative keypads (AV-701, AV-702 and AV-707) are unquestionably the user-friendliest

remote station, designed to enable easy control of the system by the end-user, as well as by the

installer. For PRO users: AV-706/7 LCD keypads have a separate manual, wiring and features are

unchanged, read this manual before using and installation.

Version 2.08 - 2.17 news

 Four new features as described in address 073

 Improved display of AC fail during armed mode

 Auto Arming option

 New Tamper features and software filtering

 Improved telephone interface meets international standards

 Selectable ‘0V’ or ‘Low’ at alarms outputs

 2.09: Sleep Mode during AC fail. Zone bypass recorded in the history log, SVM module can be

triggered by SLO or by ON output. Improved programming of user code – Pause after entering the

user index

 2.10: Ring Detector with software rings counting

 2.11: Ring Detector adjustment by software at address 093, new address 074-3

 2.12: Available at 2000 PRO: New eight automatic timers. ‘Green Reset Zone’ default to all zones

 2.13: For special PRO version with Aux. Power Cut; provides control via SLO (074-4)

 2.14: Special PRO UK version; 250 events log, central station verification

 2.16 PRO only; two bypass groups, Police Zone, supports AV-707B, telephone line monitor, line

fault listed in events log

 2.17: Improved PCB with additional +12V terminal, New Panic Zone; address 045, enhanced

events log display, telephone line monitor, zones set to Green type by default, new ring detector

features at address 095, 096 provides answering machine bypassing, three Bypass Groups. AC fail

report to dialer, AC fail report delay.

1.2  Features

 Accepts normally closed or normally open alarm devices, Tamper indication per zone

 All features are programmable via system keypad or remote modem

 Advanced static and lighting protection; unique Lighting Pro circuit for total protection

 Auto arming set by end user and/or installer

 Central station communicator and built-in TBR-21 or AUSTEL approved telephone dialer.

Communicator is compatible with most major formats: Contact ID, Ademco fast and slow,

Radionics, Scantronic, Sescoa, etc

 Chime programmable for each zone

 Digital zone-status display

 Double-Pole zone. Tampering indication for each zone

 Dialing Mode: Pulse or DTMF. Dialing to pagers in Hong-Kong and Singapore

 Electronic fuses: Aux. Power, battery and siren/bell outputs (2)

 Group bypass for three groups

 Keypad sounder during local alarm

 Local clock with ‘set time warning’

 Modulated 2-tone siren from 24H and panic zone(s), 3-tone alarm from burglary zone(s)

 Programmable 3 output drivers for remote signaling and reset of smoke detectors

 Programmable 5 or 8 EOL resistor zones, or non-EOL zones

 Pulse-operated battery charging circuit

 Low battery indication

 Signals to central station monitoring (via wire or wireless)

 Remote control via DTMF phone (available with AV-2008D only)

 Voice module option (SVM-40)

 Up and Download via RS-232, or telephone line using a PC modem

 Up to 250-alarm log (PRO version), with time and date stamped

 Up to eight EOL supervised double-zones

 Up to eight user codes, each code of up to six digits

1.3  Programmable Features

 24-hour zones, fire zone

 End of Line (EOL) zones (EOL is selectable)

 Automatic bypass of open (troubled) ‘instant’ zones upon arming

 Delayed, Follower (conditioned), Not In Use, Day, Tamper or Instant zones

 Individual entry delays for two zone groups

 Selectable response time for individual zones

 Selective and Zone Group Bypass (Group Shunt)

1.4  Alarm Outputs

 Three programmable open collector output drivers for remote alarm signaling

 Auxiliary output for electric door strike operation

 Communicator to central station and alarm sound dialer

 Keypad sounder alarm programmable per zone

 Two-timed siren outputs, each protected by separate fuses. Programmable ‘Bell Mode’

 Variable siren tones for different types of zones

 Signal test to central station, signaling time is programmable

 Remote Signals:

 24H-zone Alarm

 On/Off (Arming/Disarming) indication

 Programmable transmitting time of signal test to Central Station

 Panic per zone

 Programmable outputs for each zone or event (SLO and A1 output)

1.5  Technical Specifications Series 2000

Operating Temperature -10C to 60C

Relative Humidity 80% maximum

Input AC Power 16V AC step-down Transformer

Rated current: 1.2 Ampere

Dynamic Inner Memory EEprom

Auxiliary Power Output 13.6 Volts +/- 5%, Regulated

Short & Overload circuit protection

Siren Outputs (x2) Siren or Bell Selectable

Bell Mode: 13.6V DC-0.65A

Fuse protected

Siren: 8 Ohms, 20W

Dialer: Programmable 3 telephone numbers & 1

Follow-Me telephone number (4 tel. numbers).

Three tel. Interfaces are available: 600Ω, E, AS

Voice module input. Multi-format central-station

communicator. E version is TBR-21 approved, AS

version is AUSTEL approved

Pulse Dialing programmable

parameters

DTMF: Touch Tone dialing 

Max. Telephone number length:

16 digits and 4 pauses.

Remote Indications on Wire Terminal Open Collector type output

300 mA Max. @ 12V DC

EOL Zone Loop Resistor (Burglary)

EOL Zone Loop Resistor (Tamper)

2,200 Ohms, 0.25W, +/- 5%

4,700 Ohms, 0.25W, +/- 5%

Zone Loop Voltage 5 to 6.5 V DC

Zone Loop Current 3 mA with End-Of-Line Resistor

RFI and EMI protection Zone line shorting, cutting, high

voltage lightning protection, RF Metal

Screen, Electro Static Discharge

Traps, RF Filters. Telephone line

Lighting protection circuit

Auxiliary Power (Max.) AV-2005/8: 13.6 VDC 0.9A

Combined Aux. Power and Keypad

outputs

Battery Charging Current (Max.) 550 mA, current limitation

Battery Test: Indication at keypad or remote

indication via communicator.

Battery monitors cut-off circuit at Golden version

Performed at 0.5A load for 1 second.

Low Battery indication below 10.5V

Tested upon Arming and every 60

minutes during Armed and Disarmed

Standby Power Consumption at Disarmed mode,

and Keypad display is Off

90 mA, +/- 10 %

Maximum Remote Station (Keypads) 3 Keypads AV-701TS, AV-701TI

5 Keypads AV-702

5 Keypads AV-707

Remote Station Current Consumption AV-701TS: 27mA. AV-701TI: 36mA

AV-702: 40mA. AV-706/7: 60mA

Housing Dimensions (H) 30, (D) 9, (W) 23 cm

Housing Anodized, lockable metal box

Epoxy anti-static powder painted

Gross Shipping Weight 2.2 kg. 6 PC's per master box

Fuses: Electronic Resetable Fuses Auxiliary Power: 1.25A

Sirens: 2 X 1.25A (fuse for each siren)

Backup Battery Fuse: 2.5A

Av-Gad Systems Ltd. reserves the right to modify and upgrade products without prior notice.

Starting version 2.09 New Fuse Included - Electronic Fuse Overview

The Electronic Fuse (resetable) device is installed as a series element in a circuit. In response to an over

current, it protects the circuit by going from a low-resistance to a high-resistance state that reduces the

current to a level that’s safe for the circuit elements. The change in resistance is the result of a rapid

increase in the temperature of the device. Like traditional fuses, Electronic Fuse devices interrupt the flow

of dangerous high current. But unlike traditional fuses, they automatically reset after the fault is cleared and

power to the circuit is removed. Because they are solid-state, Electronic Fuses are also able to better

withstand mechanical shock and vibration. This fuse provides reliable protection in a wide variety of

applications. In case of over current, carefully touch the fuse body (yellow round disc), hot body means the

Electronic Fuse is in protection mode, disconnect the load and wait 2-3 minutes until the fuse body gets

cooler.

Series 2000 compared to series 860

The new Series 2000 control panels is a result of long research and exploration we at Av-Gad did among

our customers, installers and end-users requirements. In late 1998, we started the R&D and design of the

Series 2000 new systems that will keep customers smile and our QC guys happy.

Our main task was to come with 100% protected system that will ensure high reliability, more features and

flexibility.

The result is an improved system, supporting the Series 860 way of programming and wiring, but offers

great advantages of improved assembly technology and features.

The Series 2000 contains new hardware with improved EMI, RFI and Lighting protection with a complete

new telephone interface to meet all the telephone standards in the world. New zone interface with improved

Alarm and Tamper reading that use the double-zone feature, new and more efficient battery test circuit,

new siren driver and more…..

Important: Test the alarm system weekly and/or before leaving your premises.

Verify that main AC supply is connected.

1.6  Ordering Information

Item Code Description

AV-865/8M 5 + 1 (8 + 1 for 868). Discontinued types

AV-2005/8

AV-2008D

5 + 1 zone Alarm Control Panel and Communicator/Dialer, built-in up &

download modem, options for SVM-40 and RS-232, electronic fuses. AV-

2008D provides remote control via any phone. Supports AV-701, AV-702

AV-2005/8 PRO 5+1 (8 + 1) zone Alarm Control Panel and Communicator or Dialer, built-in

up & download modem. Provides connection of voice module as SVM-40.

RS-232 socket included. Supports LCD keypad types AV-707, AV-706.

PRO types are compatible only with LCD keypad

AV-2005/8AS

AV-2008 Golden

5/8 + 1 zone Alarm Control Panel and Communicator or Dialer, built-in

up/down load modem. Provides connection of voice module as SVM-40. RS-

232 socket included. Battery monitors cut-off at AV-2008 Golden version.

AV-2005/8AS is Australian version, with AUSTEL approved telephone

interface. Supports AV-701, AV-702. PRO types are compatible with LCD

keypads AV-707, 706

TMP Tamper switch with wires for main alarm metal box. Not supplied, requires

separate order

AV-701TS Cost-saving 4-wire Keypad. 7-segment Digital Display, 4 LEDs, 12 silicon

rubber keys, and local sounder, semi-backlight. Connected to panel via 4

terminal wires

AV-701TI Identical to AV-701TS, with additional timed backlight illumination

AV-702 and

AV-702TP

New shape housing. Improved circuitry provides longer wiring and better

communication. 4-wire Keypad. 7-segment Digital Display, 4 LEDs, 12

silicon rubber keys with protection door, local sounder. Similar to AV-701.

AV-702TP with Tamper switch

AV-707/TP

AV-707B

AV-706

4-wire Keypad. LCD Display, 4 LEDs, 12 silicon rubber keys. Built-in

microprocessor. Compatible with PRO panels.

AV-707TP, AV-706TP with Tamper switch, AV-707B, BG, BS are supplied

with 3 functional buttons

5003TER Fuse-protected 220V step-down to 16V-1.2A AC transformer, wire terminal,

line filter, fits all AV-2005 and AV-2008 panels

5003 Low cost 16V-1.2A transformer

RELAYMO Relay module for driving self-powered siren.

SVM-40/60/90 Speech module, record & play, message stored without power, 40, 60 or 90

second message may be split into 2 channels. Message is recordable without

additional programmer.

AV-21 and

AV-21B

Extra 12V-1.5A, power supply and charger, supplying the power for large

installations. AV-21 supplied as PCB. AV-21B supplied as PCB housed in

metal box.

SECTION II: INSTALLATION

System planning

When the panel reaches you it will be factory programmed. This is done for testing purposes and for

average installation, if required without first entering to programming. This present program is

referred to as ‘Factory Defaults.’ It is advised that the engineer should be familiar with all the

features and options before attempting to program. Keypad should be specified and ordered

separately (several types available). Default arming code (user 1) is 1,2,3,4. Default programming

code is 1,9,9,4. For best results please read the manual before installation and programming.

Tips to first time installer

If you are a first time installer, don’t hook up any remote sensors yet. The most common confusion

comes about when the alarm will refuse to arm, because a zone is “troubled”. Complete the power

supply, siren, keypad and strobe wiring, and for the moment connect ALL the zone terminals to –V

with loops of wire. This will simulate a system with all zones looped out through closed switches and

no EOL resistors. The alarm is supplied already programmed with an “average” list of settings

(default) and can be used straight away, a few of the program locations may have to be changed to

suit the actual sensors and output devices used.

 Read this manual carefully, it looks complicated, but all the information is there

 If you are using a PRO panel carefully read the manual supplied with your LCD keypad. LCD and LED

keypads cannot operate in the same system. For AV-2008D (remote DTMF) refer this type appendix

 To start with: Hook up the keypad, connect all zones to –V, power-up by applying AC only

 In case the keypad displays ‘garbage’ verify the minus (-V) wire connection

 Arm and disarm the system, when the Status LED light (not blinking), enter your master code; 1234

 Try the hold-down functions. Hold each key for approximately 2 seconds; follow the confirmation letters

in keypad’s display

 Set the system time by holding-down key ‘1’ then ‘0’, enter the time in 24 format, this will stop the blinking ‘h’

 The default programming is set for siren; the siren is plain speaker horn, if your alarm device requires 12V

to alarm, you have to change the programming to Bell mode

 Connect the strobe light to the SLO output (requires programming). The SLO supplies –V during alarm

 Make sure you are using the Earth terminal for Grounding; it’s not a minus terminal

 Typing six erroneous codes will lock the keypad keys for 30 seconds, don’t change code for starting

1. MOUNTING

1.1  Control Panel Mounting

Refer to detailed wiring diagram on page 61. Note: ‘h’ is displayed after power-up and upon Arming

to remind user to set the system time; ‘h’ will be removed after time setting, by using keys 0 and 1,

(refer to page 22, 26). Install the panel in a ventilated place, far away from RF transmitters or other

electric noise generators.

Easy as 1,2,3

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Teléfono móvil de AV-GAD

AV-GAD

AV-GAD EasyLoader AV-2016D Manual de usuario

Manuales populares de Teléfono móvil de otras marcas

Zte

Zte BLADE A520 Manual de usuario

Nokia

Nokia Lumia 620 Manual de usuario

Blackbe;rry

Blackbe;rry KEYone Manual de usuario

Bea-fon

Bea-fon X5 Premium Manual de usuario

Blackbe;rry

Blackbe;rry 8707 Series Manual de usuario

Blackbe;rry

Blackbe;rry Storm Instrucciones de funcionamiento

LG LM-X420QN Manual de usuario

LifeWatch

LifeWatch V Manual de usuario

Bea-fon

Bea-fon SILVER LINE SL860 Manual de usuario

IKI Mobile

IKI Mobile KF4.5i Manual de usuario

Hitech

Hitech HT-850 Manual de usuario

Yezz

Yezz Fashion F10 Manual de usuario

Point Mobile

Point Mobile PM60 Manual de usuario

Blackbe;rry

Blackbe;rry Q10 Manual de usuario

Blackbe;rry

Blackbe;rry Bold 9900 Manual de usuario

Blackbe;rry

Blackbe;rry STORM 9500 - VERSION 5.0 Manual de usuario

LG LM-K420EMW Manual de usuario

ISAFE MOBILE

ISAFE MOBILE IS655.2 Manual de usuario