Autonumis Brasserie Guía de solución de problemas
User & Installation Guide
This guide contains instructions for
all Autonumis’ Brasserie model
dispensers.
Brasserie
Document: NT000073 Issue: 14
Guide de l'utilisateur / notice
d'installation
Ce guide contient des instructions
applicables à tous les distributeurs
Brasserie d'Autonumis.
Installations- und
Bedienungsanleitung
Diese Anleitung eignet sich für alle
Modelle der Autonumis Brasserie-
Serie.
Gebruiks- en
installatiehandleiding
Deze handleiding bevat instructies
voor alle Brasserie-dispensers van
Autonumis.
IIEnglish / Français
Contents
English
Installation 02
Loading packs 03
Thermostat adjustment 05
Cleaning & Maintenance 05
End of life disposal 29
Machine specification 30
Spares ordering 31
Sparesidentification 33
Wiring diagram 35
Due to our policy of continual product improvement any diagrams and illustrations of the product
and/or its component parts contained within this document may appear different from that/those
supplied. However the contents of this document and the functionality of the product and/or its
components that it describes remain unaffected.
Contenu
Français
Installation 09
Chargement de produit 10
Réglage du thermostat 12
Nettoyage et entretien 12
Mise au rebut en fin de vie 29
Spécifications de la machine 30
Commande de pièces détachées 31
Identification des pièces détachées 33
Schéma de câblage 35
En raison de notre principe d'amélioration continue des produits, les schémas et illustrations du
produit et/ou de ses composants figurant dans ce document peuvent sembler différents de
celui/ceux fourni(s). Cependant, le contenu de ce document et la fonctionnalité du produit et/ou
des composants qu'il décrit restent inchangés.
III Deutsch Nederlands/
Inhalte
Deutsch
Installation 16
Laden des produkts 17
Einstellen des thermostats 19
Reinigung und pflege 19
Entsorgung 29
Technischedaten 30
Ersatzteilbestellung 32
Ersatzteile 33
Schaltplan 35
Aufgrund unseres ständigen Bestrebens um Produktverbesserungen können die in diesem
Dokument enthaltenen Diagramme und Illustrationen für das Produkt und/oder seine Bauteile von
den tatsächlich gelieferten abweichen. Der Inhalt dieses Dokuments sowie die Funktionen des
darin beschriebenen Produkts und/oder seiner Bauteile sind davon jedoch nicht betroffen.
Inhoudstafel
Nederlands
De installatie 23
Laadpakken 24
De thermostaat verstellen 26
Shoonmaken en onderhouden 26
Van de hand doen 29
Machinespecificaties 30
Reserveonderdelen bestellen 32
Identificatie reserveonderdelen 33
Bedradingsschema 35
Vanwege ons beleid dat op voortdurende verbeteringen gericht is, kan het voorkomen dat
diagrammen en afbeeldingen van het product en/of onderdelen daarvan in deze documentatie
verschillen van het eigenlijke product/onderdeel. De informatie in dit document en de functies van
het product en/of de onderdelen daarvan die erin worden beschreven, zijn echter ongewijzigd.
The Brasserie Dispenser
01
Lower Door MouldingDispense Valves
Drip Tray Stand
Shroud
Door Catch
Top Cover Moulding
Light Switch
English
02
Machine Installation
Securing The Dispenser ToA Work Surface
Select a level stable surface that is capable of supporting the weight of
a filled dispenser.
Secure the anti-tilt mounting bracket in the desired location on the
chosen surface using suitable fixings (Fig 2a).
Secure the machine to the anti-tilt mounting bracket using the two M5
thumbscrews provided (Fig 2b).
Setting Up The Dispenser
Connect the machine to a
standard power supply.
Insert the dispense valves
into the machine (Fig 1).
Install the drip tray bowl and
stand (Fig 3).
Fig 2a.
Fig 2b.
Fig 3.
English
03
Loading Packs
Filling The Dispenser
If you have been supplied with a ‘bag in box’ carton for your dispenser, follow
the instructions below.
Please note that the “Raised Cooling Shelf” is required when dispensing
Smoothies. This part is available through our sales department. See “Spares
Parts Ordering” within this User Guide.
Release the door catch on the machine and remove the used pack.
Clean the interior of the machine if necessary (see Cleaning
Routine).
Open the pack as instructed on the carton. Now place the full pack into
the cabinet with the dispense tube facing downwards at the front of the
machine.
Feed the dispense tube down through the dispense valve whilst
pushing the operating lever (Fig 4a).
When the tubing is fully through the dispense valve, release the
operating lever.
Close the door and door-catch. You can now cut the sealed end of the
dispense tube (Fig 4b).
If you are using the optional basket for bag only products, then follow the
appropriate instructions below.
Open the wire basket provided and place a full bag within. On some
models basket hooks are provided to secure the bag (Fig 5). Ensure
that the plastic nozzle with the attached tube is located in the
corresponding basket slot (Fig 6), then close the basket.
Replace the filled product basket into the dispenser in an upright
position. For the product to be dispensed properly you must ensure
that the tube is free and hanging vertically.
Feed the dispense tube down through the dispense valve as per the
‘bag in box’ carton instructions above (Fig 4a).
English
04
Fig 4a. Fig 4b.
Fig 6.Fig 5.
2
1
Operating
Lever
Where available
English
05
Thermostat Adjustment
Cleaning & Maintenance
Cleaning Routine:
Wash the drip tray daily, or when full.
Clean the interior of the machine whenever a used pack is replaced.
The dispense valve assembly can be completely immersed in warm soapy
water for cleaning whenever convenient.
The top and bottom hinges should be regularly cleaned using warm soapy
water applied with an appropriate cleaning brush.
The door seal is a sealed section and as such requires no cleaning. However
the area behind the seal should be cleaned regularly with warm soapy water,
and thoroughly dried. Drainage holes are provided to facilitate this.
The exterior of the machine may be wiped with a damp cloth and buff dried.
To set the desired temperature (Fig 7):
Press the button (the current set temperature is now displayed).
Then press the or button to modify the displayed value.
Finally press the button to store the value and exit the adjustment. If no
more buttons are pressed within 10 seconds then the display will once more
show the current internal temperature of the unit.
Fig 7.
English
06
No routine maintenance is required beyond the cleaning routine illustrated,
however if the product is not cold enough:
Check the power supply is on, and the fuse is not blown,
Check that the temperature is adjusted correctly (see Thermostat
Adjustment section).
If the liquid is too cold:
Check the temperature setting (see Thermostat Adjustment section).
If the lights do not operate:
Check power supply.
Is light switched on?.
Replacing The Lights
Warning: Ensure the machine is disconnected from the main power supply
before replacing lights. If in doubt, consult a qualified electrician.
Removal of the Graphic Display Area LED Light Strip
See corresponding numbers of (Fig 8).
1. Slide the fascia panel up to reveal the Light Cover.
2. Remove the Light Cover to reveal the LED Light Strip.
3. Remove the screws from the top and bottom of the LED
Light Strip and disconnect the power connector.
Removal of the Dispense Area LED Light Strip
4. Remove two screws from the base of the cover moulding
5. Remove two screws from the LED Light Strip and
disconnect the power connector.
English
Trouble Shooting Guide
2
1
3
4
5
Fig 8.
English 07
This appliance contains R600a refrigerant. This is a flammable gas and it is
important to avoid damage to the refrigeration system during transportation
and installation. Do not use mechanical devices or other means to
accelerate the defrosting process. In case of damage to the refrigeration
circuit, avoid using a naked flame close to the unit, ventilate the room and
call an authorised service contractor.
* In some cases your appliance may be supplied with R134a refrigerant
(please check your appliance serial number label), note this is a non
flammable gas and the above warning does not apply.
Tabla de contenidos
Idiomas:
