3
www.AutomationDirect.com
1-800-633-0405
5. Connect Power to the Monitor
• Power source needs to be 100 - 240 VAC, 50/60 Hz.
• See power connection diagram to the right.
• Secure plug retention screws to monitor.
• Power should not be applied until all cables are attached and the monitor is
ready to operate.
Damage can occur if power is not properly connected.
WARNING - EXPLOSION HAZARD: Do not disconnect equipment while the
circuit is live unless the area is known to be free of ignitable concen-
trations.
6. Apply Power to the Monitor & PC
• Press the DISPLAY POWER button on the rear of the monitor to wake the
monitor up. Pressing the DISPLAY POWER button again turns off the backlight
inverter and puts the monitor in a reduced power state but the touch screen
remains active. It is important to note that this switch does not disconnect
power from the monitor. Power is always supplied to the internal AC/DC
power supply, which in turn continually supplies power to the internal monitor
electronics and the optional touch screen controller.
7. Install the Appropriate Touch Screen Driver
• The calibration of the touch screen occurs by a calibration utility that installs as
part of the touch screen driver installation process.
• Applies to touch screen version only.
• Download the touchscreen driver files from the product page at automation-
direct.com
• Install the touch screen drivers for the particular PC operating system being
used. Before installing the drivers, please read the Touch Screen Driver
Documentation for operating system details.*
• Reboot the PC and and restart the monitor to activate the driver.
*Note: for Models with seriAl NUMbers before N2220 Use
the elo drivers. for Models with seriAl NUMbers N2220 ANd
hiGher Use the eGAlAx drivers.
9. Adjust the Monitor OSD Settings as Required
• Press the Select (Auto Adj) control button on the rear of the panel to initiate an
automatic configuration of the screen.
• Although normally not needed, the control buttons on the rear of panel can be
used to make other adjustments to the screen.
• Consult the Hardware User’s Guide, ATM-USER, located in the documenta-
tion area of the automationdirect.com website for detailed usage of the OSD
settings.
10. Installation Complete
Power Connections:
TOP VIEW
FRONT VIEW
ADC P. N. ATM-AC-CON or
PHOENIX CONTACT P. N. 1777992
L N
Plug Retention Screws
Power
Connection
Label
PE
100 VAC - 240 VAC INPUT (1.0 Amps Min)
312
PIN No. Definition
1AC Line Input
2AC Neutral Return
3Protective Earth Ground
Required Wire Specification
Wire Size 18 - 12 AWG (0.8 - 3.3 mm2)
Wire Material and
Temperature 60°C or 60 / 75°C Copper
Tightening Torque 7.0 lb·in (0.79 Nm)
Panel Power Draw
ATM1500 (T) ≤25W
ATM1700 (T) ≤30W
ATM1900 (T) ≤35W
WARNING - EXPLOSION HAZARD: Substition of any components may
impair suitability for Class 1, Division 2.
Display Power
Button
Power
Indicator
DISPLAY POWER
WARNING
Touch Screen is still
active while display
power is off
MAIN MENU
BRIGHTNESS/CONTRAST
1280X102463.9KHZ/60HZ
COLOR
POSITION
SETUP
EXIT
R G B
WARNING - Touchscreen is still active while display is off.
ATTENTION – L’écran tactile est toujours actif, méme quand l’afficheur
n’est pas alimenté.
ADVERTENCIA – La pantalla táctil sigue activa aún cuando el display
esté apagado.
WARNUNG – Touch screen ist immer noch aktiv, während die
anzeigefläche ausgeschaltet ist.
WARNING - The monitor does not automatically select a video input
mode. The user must press the “UP (VGA/DVI)” button on the rear of
the monitor to select either VGA or DVI input. If a “No Video” message
appears on the screen, it is also suggested the user try using the “UP
(VGA/DVI)” button to select the active video input.
*Note: oNce yoU hAve coNNected yoUr pc ANd the MoNitor,
selected the video soUrce ANd powered both UNits, it is
sUGGested thAt the “select (AUto AdJ)” bUttoN oN the
reAr of the MoNitor be pressed to MAxiMize the video settiNGs.
8. Verify Video and Touch Screen Functionality
• Verify the monitor’s video display by running a familiar program.
• If using the touch screen model, use the touch screen to navigate by running a
familiar program.
LCD Power Button:
OSD Settings Main Menu:
