Autoglide FERO 600-M Manual de usuario

Intelligent Remote Control Swing Door Opener

Instruction Manual

Model – Fero 600-M

Control box

Contents Pages

Ⅰ. Summary 2

Ⅰ. Structures & Classification 2

Ⅰ. Main Technical Parameters 3

Ⅰ. Function Characteristics 3

Ⅰ. Operating Methods 3

Ⅰ. Installation Method & Debugging 4

Ⅰ. Maintenance and services 8

Ⅰ. Trouble shooting 8

Ⅰ. Control Board 9

Ⅰ. System S ett in gs

1 1

Ⅰ. A t t e n t i o n s

1 4

Ⅰ. Safety & Cautions

Ⅰ. Summary

Dear user:

Thank you for selecting of our intelligent remote control swing gate opener! Please

carefully read this Instruction Manual before installation and use.If you have any problem

that you can’t settle during use, please contact your local distributor of our products.

Ⅰ. Structures & Classification

1. Opener structure: as Fig. 1

Fig.1

2.Control and power distribution structure, as shown in Fig.2

Fig.2

3.Classification of gate opener: Inward gate opener and outward gate opener.

4.Classification of Control system: 2- channel 5- line ordinary control system and 2- channel 2- line

wisdom control system.

Ⅲ

. Main Technical parameters

Ⅳ. Function Characteristics

1. Single-leaf or double-leaf opening: This function can be activated by pressing button.

2. Control box locking: To avoid unauthorized opening, this function can be activated by

remote control.

3. Automatic detection and protection: The gate opener will automatically stop if any

obstruction is detected during opening; it will return to the original position automatically if

any obstruction is detected during closing.

4. Infrared detection and protection: The gate will automatically re-opened if any passing

vehicle or person is detected during closing.

5. Automatic detection and access control: The gate opener can be connected to card

reader, fingerprint scanner, anti-theft alarm, camera or any other devices for automatic

access control.

6. Gate operating indication: The blue LED light on the gate opener will flash during gate

opening, the red LED light on the gate opener will flash during gate closing, indicating

vehicle and pedestrian that the gate opener is operating, make attention to the

safety.(Optional)

7. Back up battery interface: The gate opener will be automatically switched to storage

battery or solar cell mode upon external power failure.

8. Sequential operation: The gate opening angel and sequence can be set.

Please refer to the Instructions Manual of the control box for the foregoing functions,

interfaces and detailed operating and setting methods.

Ⅴ

. Operating Methods

This gate opener can be controlled electrically and manually. Please remove any

obstructions within the working scope of the gate body and no vehicle or person allowed

access during operation.

(I) Electric control operation

1. Press the button of the control box to realize automatic gate opening, closing or stop.

2. Press the button of the remote control to realize automatic gate opening, closing or

stop.

3. The gate access control system can identify and control access automatically.

(II) Manual control operation

1. Manual opening: insert the clutch key into the lock hole and rotate it clockwise to

disengage the clutch (the gate opener in manual mode), then push the gate open by hand.

2. Manual closing: push the gate to near the close position when it is in manual mode, insert

the clutch key into the lock hole and rotate it anticlockwise to engage the clutch(the gate

opener now in electric mode),then push the gate to the lock position by hand.

Fig. 3 Manual and electric switching

Ⅵ

. Installation methods & Debugging

(I) Preparation

1. Check the flexibility of the gate during opening and closing, make sure that the gate does

not bounce back when the gate reaches the open or close limit position.

When the gate is in the close position, the bottom edge of the gate frame shall be at least

25mm above the ground (slightly higher than the stop iron, as shown in fig.4).Make special

adjustments if the gap is less than 25mm.

Fig.4 Heights of Gate Frame and Stop Irons

2. The unevenness of the ground within the working scope of the gate opener.

Fall h=Height of the highest point of the ground- height of the lowest point of the ground.

a) when 0

＜

h≤80mm, the fall is normal, choose the standard configuration.

b) when 80mm

＜

h≤140mm, the fall is large, choose long configuration.

c) when 140mm

＜

h≤300mm, the fall is too large, choose special configuration (dual

slide)

Determination power of the gate op

Measure the width, height, weight of the gate leaf and determine if

motor shall be chose according to the sealing conditions and external environments (e.g.

ground conditions, wind force etc.)

Choose the

model and configuratio

functional requirements.

Bury the wire pipes with reference to the wiring diagram of the power

of the gate opener

(Fig.2) and determine the diameter and number of cores of mu

flexible wires (power cables).

wo ways of system configuration

opener and control box:

a) 2-channel 2-line

gate opener

connected via two circuits of two

b) 2- channel 5-line

gate opener

connected via two circuits of five

If any infrared sensor is added,

please adopt three

sensor to the

control box, and use

transmitting terminal with receiving terminal.

If any card reader is added, please adopt four

to the control box.

Mark the position of the mounting plate on the gate body. Move the mounting plate further

downward by 10-

20mm from the

plate.

In either method, the installing height of the mounting plate

according to the ground smoothness, gate size and weight, hinge flexibility and other

factors.

Note: 1. Fasten the

mounting plate

Keep the mounting plate vertical during

body.

Make one hole on either of the inner sides of the gate on the bottom fame (for entry and

exit of wires) for wires. One flexible sleeve cover the wires shall be used where they go

through the holes.

Determination power of the gate op

ener

Measure the width, height, weight of the gate leaf and determine if

ordinary or high

motor shall be chose according to the sealing conditions and external environments (e.g.

ground conditions, wind force etc.)

model and configuratio

n of the gate opener according to

the user type and

Bury the wire pipes with reference to the wiring diagram of the power

distribution

(Fig.2) and determine the diameter and number of cores of mu

wo ways of system configuration

are available according to the conne

ction ways of gate

gate opener

and control box

the gate opener and the control box are

core power cables.

gate opener

and control box

the gate opener and the control box are

core power cables.

please adopt three

core power cables to conn

control box, and use

two-

core power cables to connect the infrared sensor

transmitting terminal with receiving terminal.

If any card reader is added, please adopt four

core power cables to connect the card reader

Mark the position of the mounting plate on the gate body. Move the mounting plate further

20mm from the

mark;

this is the actual installing height of the mounting

In either method, the installing height of the mounting plate

shall be appropriately adjusted

according to the ground smoothness, gate size and weight, hinge flexibility and other

mounting plate

with four bolts before mounting plate

installation.

Keep the mounting plate vertical during

installation and bolt or weld it onto the gate

Make one hole on either of the inner sides of the gate on the bottom fame (for entry and

exit of wires) for wires. One flexible sleeve cover the wires shall be used where they go

ordinary or high

-duty

motor shall be chose according to the sealing conditions and external environments (e.g.

the user type and

distribution

system

(Fig.2) and determine the diameter and number of cores of mu

lti-strand

ction ways of gate

the gate opener and the control box are

core power cables to conn

ect infrared

core power cables to connect the infrared sensor

’s

core power cables to connect the card reader

Mark the position of the mounting plate on the gate body. Move the mounting plate further

this is the actual installing height of the mounting

shall be appropriately adjusted

according to the ground smoothness, gate size and weight, hinge flexibility and other

installation.

installation and bolt or weld it onto the gate

Make one hole on either of the inner sides of the gate on the bottom fame (for entry and

exit of wires) for wires. One flexible sleeve cover the wires shall be used where they go

Fig.5 Holes on both inner sides of the gate on the bottom frame

4. Fix the gate opener

and connect the

terminal

block of the control box or the color of the plug wire).

Check:

Use the key to switch the gate

forward and backward.

The gate opener shall rise and fall freely with the fluctuation of the ground and no dead

locking, hanging and suspending etc.

5. Installation of the stop iron (

please r

When the gate is in the mode of manual operation, move the gate to the close position

and install the stop iron into the lock hook. Use the key to switch the gate opener to electric

mode and lock it there. Move the stop iron so that the centerlin

the lock hook and mark the position of the stop iron. Drill a hole on the ground and fasten the

stop iron with expansion bolts.

Fig.6

Position of stop iron and

gate(overlook)

Note

The stop iron for the gate leaf that is firstly closed shall be installed first

when the gate has a floor stop. The two stop irons shall be distanced

from each other by 10

The ground where the wheel

ground where the stop irons are rested shall be on the same level when the

gate is at the close position.

c) If

any rubber buffer is to be installed between the pressure plates of the

two leaves, they should be ins

Otherwise, the reliable locking of the gate opener may be affected and the

proper operation of the gate opener may even be disabled.

d) The stop irons

should be

loose

ned or displaced in operation.

Fig.5 Holes on both inner sides of the gate on the bottom frame

and connect the

wires (

whose color shall be the same as label of

block of the control box or the color of the plug wire).

Use the key to switch the gate

opener to manual mode and push the gate body

The gate opener shall rise and fall freely with the fluctuation of the ground and no dead

locking, hanging and suspending etc.

please r

efer to the following points):

When the gate is in the mode of manual operation, move the gate to the close position

and install the stop iron into the lock hook. Use the key to switch the gate opener to electric

mode and lock it there. Move the stop iron so that the centerlin

e of the lock hole is aligned to

the lock hook and mark the position of the stop iron. Drill a hole on the ground and fasten the

Fig.7

gate(overlook)

Position

of stop iron and lock hook

The stop iron for the gate leaf that is firstly closed shall be installed first

when the gate has a floor stop. The two stop irons shall be distanced

from each other by 10

-15mm.

The ground where the wheel

s of the gate opener are rested and the

ground where the stop irons are rested shall be on the same level when the

gate is at the close position.

any rubber buffer is to be installed between the pressure plates of the

two leaves, they should be ins

talled before the gate opener is installed.

Otherwise, the reliable locking of the gate opener may be affected and the

proper operation of the gate opener may even be disabled.

should be

installed firmly and they shall not become

ned or displaced in operation.

Fig.5 Holes on both inner sides of the gate on the bottom frame

whose color shall be the same as label of

opener to manual mode and push the gate body

The gate opener shall rise and fall freely with the fluctuation of the ground and no dead

When the gate is in the mode of manual operation, move the gate to the close position

and install the stop iron into the lock hook. Use the key to switch the gate opener to electric

e of the lock hole is aligned to

the lock hook and mark the position of the stop iron. Drill a hole on the ground and fasten the

of stop iron and lock hook

The stop iron for the gate leaf that is firstly closed shall be installed first

when the gate has a floor stop. The two stop irons shall be distanced

s of the gate opener are rested and the

ground where the stop irons are rested shall be on the same level when the

any rubber buffer is to be installed between the pressure plates of the

talled before the gate opener is installed.

Otherwise, the reliable locking of the gate opener may be affected and the

installed firmly and they shall not become

Manually open and close the gate to check if the stop irons are properly installed.

a.Push the gate towards the stop iron when the gate is in manual mode, then use the key to

switch it to electrical mode. Push the gate forward and the gate shall be reliably locked.

b.Use the key to switch the gate opener back to manual mode and the gate can be easily

pushed open.

6. Installation of limit magnet for opening

Open the gate to maximum or designed position and retreat it by 200mm.Find the ground

projection of the magnetic switch at the bottom of the gate opener, drill a hole there (Ø22mm)

and bury a magnet leveled with the surface.

Magnet

(IV) Operation and debugging of the electric gate opener

Check if the wiring is properly done and if the voltage meets the requirements before

operation. Use the key to disengage or engage the clutch and check if the gate can be

properly manually opened and closed. Push the gate to the mid-position and engage the

clutch of the gate opener (in electric state).Switch on the mains power and the indicators are

in normal condition.

1. Press the button of the remote control or the control box to open, stop and close the

gate .Observe if the gate opener works in a stable and consistent manner and if it

automatically stops in an accurate manner when the required position is reached.

Otherwise, check it relevant parts are properly installed.

2. Check if the gate moves in the right direction as displayed by the control key. Otherwise,

please correct wiring of the gate opener or motor.

3. Please see the control box’s Instructions Manual for the locking method of keys.

4. Debugging of automatic stop upon obstacle and motor’s loading capacity: it is necessary

to appropriately adjust the potention meter (pressure or resistance) of the control box

according to the gate size, hinge flexibility and ground evenness in order to increase or

decrease the motor’s capacity against resistances.

5. Test methods of automatic stop upon obstacle during opening , and re-open upon

obstacle during closing:

a) Apply a counterforce (push or pull with hands) on one leaf during opening and the

gate shall stop opening.

b) Apply a counterforce on one leaf during closing and both leaves shall retreat in the

opening direction. If the motor’s capacity against resistance is set to be too small the

motor may easily stop operation. If it is set to be too big, the protective effects may be

reduced.

6. Please read the control box’s Instruction Manual for the protection time of the gate during

operation. If the protection time is setting too short, the gate will stop automatically

before it reaches the desired position.

7. Please read the control box’s Instruction Manual for setting and time adjustment for

automatic gate closing.

8. The time difference for delayed closing of the gate leaves shall be adjusted according to

the different degrees of opening of both leaves.

9. Please see the Instruction Manual for details about the card reader, infrared protector

and wiring.

Ⅶ

. Maintenance and services

1. The turning parts of the gate opener shall be kept clean and free of any attachments.

2. Frequently clean away the debris in the grooves of the stop iron.

3. Properly lubricate various mechanical moving parts very quarter.

4. Check the power protector and the performance conditions of the backup storage battery

once a month.

Ⅷ

. Trouble shooting

Instruction Manual for Control Panel

With soft start and soft stop low speed wisdom type

Product model: Two wires multi-function wisdom type

FERO 600-M

System Methods: remote control and motor integrated with intelligent control

Object: Two channels two wires inward (outward) swing gate opener

Main electrical function: AC, DC type (AC 220V, DC 24V)

Rated power: 180W

Wiring distance: within 30 meters

Remote control distance: within 30-50 meters

Installation: Wall-mounted or desktop

Frequency: 433.92MHZ learning encrypted rolling code type

FERO 600-M Control Board

FERO 600 control board is specially designed according to 24V DC door opener, improved through

D33. With soft start and soft stop low speed function, encrypted remote control ,higher

confidentiality .This system can also optionally available with a back-up battery. When power off,

the battery provides 24V DC power supply to continue working. The battery must be installed

reversely, to avoid wall bracket hit power terminals during installation. As long as the door work

under correct procedure, the circuit board do not need maintenance normally. Install the control

panel as close as possible to the place w

of 1.5mm 2 core wires, to reduce the pressure drop and ensure system

Ⅰ. Function and features:

1. Anti-collision design:

when the door travel is completed, only after press reverse key, t

can be activated so that the over-

travel can be avoided.

2. Motor time protection:

Avoid long time running when travel failure, the time set to 2

seconds.

3. Auto close function: the time

can be adjusted from 1~240

4. Motor strength adjustment

: motor running strength can be adjusted separately. When barrier

blocks, the door stops travel in case of clamping people or object.

Motor opening and closing low speed function:

steady .

6. High security:

remote control with high

anti-interference. Using

the most advanced jump codec technology, more safe and secretive than

the traditional remote control (code number 6561 groups) in the

100 million units, can not be deciphered.

7. Anti-clamping function:

During door

door will automatically stop and run in the opposite direction, to prevent injuries or folder object.

8. LED fault display:

it is easy to carry out maintenance and use through LED screen.

Ⅱ. Red DIP switch setting:

RED DIP switch function of the control panel can be setting as followings

Red DIP switch 1 = Remote control with single key and three key interch

Turn on RED DIP switch 1 to OFF =

individually.

Turn on RED DIP switch 1 to ON = single key cycle, that is which key to be coded that is the key

perform cycle action. For example: use

again=door stop, press open

once more=door close,

this way.

Red DIP switch 2 = Opening sequence function

Turn on RED DIP switch 2 to OFF ,

gate 1 and gate 2 open at the same time.

Turn on RED DIP switch 2 to ON

, gate 2 will open 5 seconds earlier than gate 1.

under correct procedure, the circuit board do not need maintenance normally. Install the control

panel as close as possible to the place w

here the door motor is connected with minimum diameter

of 1.5mm 2 core wires, to reduce the pressure drop and ensure system

performance.

when the door travel is completed, only after press reverse key, t

travel can be avoided.

Avoid long time running when travel failure, the time set to 2

can be adjusted from 1~240

seconds.

: motor running strength can be adjusted separately. When barrier

blocks, the door stops travel in case of clamping people or object.

Motor opening and closing low speed function:

this function make the door running more

remote control with high

sensitivity, far

remote distance and strong

the most advanced jump codec technology, more safe and secretive than

the traditional remote control (code number 6561 groups) in the

market. Password

100 million units, can not be deciphered.

During door

closing, when

there are obstacles blocking the

door will automatically stop and run in the opposite direction, to prevent injuries or folder object.

it is easy to carry out maintenance and use through LED screen.

RED DIP switch function of the control panel can be setting as followings

Red DIP switch 1 = Remote control with single key and three key interch

ange:

Turn on RED DIP switch 1 to OFF =

open stop close Single

four keys control

Turn on RED DIP switch 1 to ON = single key cycle, that is which key to be coded that is the key

perform cycle action. For example: use

open to study , press open

= door open,

once more=door close,

press open

again=door open, cycle in

Red DIP switch 2 = Opening sequence function

gate 1 and gate 2 open at the same time.

, gate 2 will open 5 seconds earlier than gate 1.

under correct procedure, the circuit board do not need maintenance normally. Install the control

here the door motor is connected with minimum diameter

performance.

when the door travel is completed, only after press reverse key, t

he motor

Avoid long time running when travel failure, the time set to 2

-240

: motor running strength can be adjusted separately. When barrier

this function make the door running more

remote distance and strong

the most advanced jump codec technology, more safe and secretive than

market. Password

number up to

there are obstacles blocking the

infrared, the

door will automatically stop and run in the opposite direction, to prevent injuries or folder object.

it is easy to carry out maintenance and use through LED screen.

RED DIP switch function of the control panel can be setting as followings

four keys control

Turn on RED DIP switch 1 to ON = single key cycle, that is which key to be coded that is the key

= door open,

press open

again=door open, cycle in

Tabla de contenidos

Otros manuales de Abridor de puerta de Autoglide

Autoglide

Autoglide VELOCE 80A Manual de usuario

Autoglide

Autoglide CABRI-20P Manual de usuario

Autoglide

Autoglide MAGRO-35A Manual de usuario

Autoglide

Autoglide CASA-50P Manual de usuario

Autoglide

Autoglide Magro-500 J Manual de usuario

Autoglide

Autoglide CABRI-30P Manual de usuario

Autoglide

Autoglide CASA-120-O Manual de usuario

Manuales populares de Abridor de puerta de otras marcas

Elite

Elite CSW200UL Manual de usuario

CAME

CAME FROG-PM4 Manual de usuario

SOMFY

SOMFY FX230 Manual de usuario

Aprimatic

Aprimatic ONDA 500 Manual de usuario

Turnstiles

Turnstiles FSW 900 Manual de usuario

Erreka

Erreka BUL BL33 Instrucciones de funcionamiento

Erreka

Erreka VULCAN S Manual de usuario

Beninca

Beninca R1-2 WBV Manual de usuario

Erreka

Erreka VULCAN D Manual de usuario

Motorline professional

Motorline professional FORT Manual de instrucciones

Beninca

Beninca BOB5024 Manual de usuario

AGA

AGA GATEMASTER 900 HD Manual de usuario

Chamberlain

Chamberlain MotorLift HC280ML Manual de usuario

SOMFY

SOMFY Dexxo RTS Pro Manual de usuario

Cardin

Cardin BL Series Manual de usuario

Westfalia

Westfalia 85 27 06 Manual de usuario

CAME

CAME F500 Manual de usuario

Extel

Extel VERA Manual de usuario