Autodiagnos MULTI TESTER PRO Manual de usuario

MULTI TESTER PRO

User manual

A37MAN I318495 Iss1

Part Number A37MAN

EN - Issue 1

Multi Tester Pro

User Manual

Part Number A37MAN

Issue 1

Contents

Introduction

Introduction............................................................................................. 1

Getting Started

Setting up ............................................................................................... 2

Multi-Cartridge Manager - Installation ............................................................. 2

Multi-Cartridge Driver - Installation.................................................................. 3

Multi-Cartridge Driver - Update........................................................................ 5

Connecting Multi-Cartridge Manager............................................................. 10

Downloading applications.............................................................................. 11

Updating License........................................................................................... 12

Software updates - Website .......................................................................... 13

Snapshot Reader - Installation ...................................................................... 14

Using Multi-Tester Pro

Getting familiar with Multi-Tester Pro ................................................... 15

Connection points.......................................................................................... 15

Display and keys ........................................................................................... 16

Typical screen layout..................................................................................... 17

Keypad operation .......................................................................................... 18

Connections .................................................................................................. 19

Cable Quick Guide Chart............................................................................... 20

Display and Keys........................................................................................... 21

Communicate ................................................................................................ 21

Functionality Overview ......................................................................... 22

Monitor list ..................................................................................................... 24

Actuators ....................................................................................................... 25

Reset adaptation values................................................................................ 26

Self Test ........................................................................................................ 26

Module Synchronisation ................................................................................ 26

Snapshot Reader functions .................................................................. 27

Viewing Snapshots........................................................................................ 27

Downloading Snapshots................................................................................ 27

Contents

Support Services

Product Support.................................................................................... 30

Technical Information.................................................................................... 30

Training ......................................................................................................... 31

Autodiagnos Website .................................................................................... 31

Contact Details

Addresses............................................................................................. 32

Parts list................................................................................................ 33

Introduction

The contents of this document may be changed without prior notice, and should

therefore not be regarded as being binding on Autodiagnos.

Autodiagnos declines all responsibility for faults and omissions, which may occur in

this document, or the hardware & software described herein.

Under no circumstances can Autodiagnos be held responsible for damage, which

could occur due to use of this document, or of the hardware and software described

herein.

This document must not be wholly or partly reproduced, copied, or duplicated by any

means, nor may it be stored in an information retrieval system, except for personal

use, without written permission from Autodiagnos. Nor may the contents be divulged

to any third party or used in any unauthorised manner. Any breach of these

stipulations may lead to legal action

Introduction

The Autodiagnos Multi-Tester Pro is a hand-held serial diagnostic tool for carrying out

fault finding on Electronic Control Units (ECUs) fitted to cars and light commercial

vehicles.

The equipment has been designed to be quick and easy to use whilst still offering the

in-depth functionality required to diagnose and service today’s modern vehicle control

systems.

Getting Started

Getting S tarted

Setting up

Multi-Cartridge Manager - Installation

The Multi-Cartridge Manager software is used to manage the information held on the

Multi-Cartridge. It allows software applications and customer licence information to be

updated when required. It is recommended that this software is installed immediately,

by following these steps:

Note: Do not connect the Multi-Cartridge until advised.

1. Insert the CD into the drive; it should auto-run and display the ‘Autodiagnos’

window.

2. Press the ‘Multi-Cartridge’ button. Follow the on-screen prompts to install the

Multi-Cartridge Manager software.

Getting Started

Multi-Cartridge Driver - Installation

1. Once the Multi-Cartridge Manager installation is complete, connect the

Multi-Cartridge to a USB port on the PC. Windows will detect a new device and

display the installation wizard. Select ‘No, not this time’ and press ‘Next >’ to

continue.

Getting Started

2. Select ‘Install the software automatically’ and press ‘Next >’. Windows will

install the USB driver from the CD.

3. If a warning message saying that the driver ‘.... has not passed Windows Logo

testing....’ is displayed, press ‘Continue anyway’.

4. The Multi-Cartridge Manager software is now ready to use.

Getting Started

Multi-Cartridge Driver - Update

If the above error message is displayed when trying to start the Multi-Cartridge

Manager software but no ‘Found New Hardware’ message has appeared, then the

following procedure will update the driver.

Note: This procedure must be repeated for each USB port to which the

Multi-Cartridge is connected.

1. Ensure the latest Autodiagnos CD is in the CD drive and the Multi-Cartridge is

connected to the PC.

Tabla de contenidos

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario