Autel MaxiService EBS301 Manual de usuario

Table of Contents

1. SAFETY PRECAUTIONS AND WARNINGS.............................................. 1

2. GENERAL INFORMATION.......................................................................... 2

2.1 ON-BOARD DIAGNOSTICS (OBD) II ............................................................. 2

2.2 DIAGNOSTIC TROUBLE CODES (DTCS)........................................................ 2

2.3 LOCATION OF THE DATA LINK CONNECTOR (DLC) .................................... 3

2.4 OBD II READINESS MONITORS .................................................................... 4

2.5 OBD II MONITOR READINESS STATUS......................................................... 5

2.6 OBD II DEFINITIONS .................................................................................... 6

3. USING THE SCAN TOOL.............................................................................. 8

3.1 TOOL DESCRIPTION ...................................................................................... 8

3.2 SPECIFICATIONS.......................................................................................... 10

3.3 ACCESSORIES INCLUDED............................................................................. 10

3.4 KEYBOARD.................................................................................................. 10

3.5 POWER ........................................................................................................ 10

3.6 SYSTEM SETUP ............................................................................................ 11

3.7 VEHICLE COVERAGE .................................................................................. 15

3.8 PRODUCT TROUBLESHOOTING.................................................................... 16

4. PLAYBACK DATA....................................................................................... 17

4.1 REVIEWING DATA....................................................................................... 17

4.2 DELETING DATA ......................................................................................... 18

4.3 PRINTING DATA .......................................................................................... 18

5. OBDII DIAGNOSTICS ................................................................................. 19

5.1 READ CODES............................................................................................... 20

5.2 ERASE CODES.............................................................................................. 23

5.3 LIVE DATA .................................................................................................. 25

5.4 FREEZE FRAME........................................................................................... 31

5.5 RETRIEVING I/M READINESS STATUS......................................................... 32

5.6 O2 MONITOR TEST ..................................................................................... 35

5.7 ON-BOARD MONITOR TEST........................................................................ 36

5.8 COMPONENT TEST ...................................................................................... 39

5.9 VIEWING VEHICLE INFORMATION.............................................................. 40

5.10 MODULES PRESENT .................................................................................... 42

5.11 DTC LOOKUP ............................................................................................. 43

6. PRINT AND UPDATE................................................................................... 45

6.1. PRINT DATA ................................................................................................ 45

6.2. SOFTWARE UPDATE..................................................................................... 46

7. EPB.................................................................................................................. 52

7.1. EPB SAFETY ............................................................................................... 52

7.2. EPB MAINTENANCE.................................................................................... 52

8. WARRANTY AND SERVICE...................................................................... 57

8.1. LIMITED ONE YEAR WARRANTY................................................................ 57

8.2. SERVICE PROCEDURES................................................................................ 57

1. Safety Precautions and Warnings

To prevent personal injury or damage to vehicles and/or the scan

tool, read this instruction manual first and observe the following

safety precautions at a minimum whenever working on a vehicle:

Always perform automotive testing in a safe environment.

Wear safety eye protection that meets ANSI standards.

Keep clothing, hair, hands, tools, test equipment, etc. away from

all moving or hot engine parts.

Operate the vehicle in a well ventilated work area: Exhaust gases

are poisonous.

Put blocks in front of the drive wheels and never leave the vehicle

unattended while running tests.

Use extreme caution when working around the ignition coil,

distributor cap, ignition wires and spark plugs. These

components create hazardous voltages when the engine is

running.

Put the transmission in PARK (for automatic transmission) or

NEUTRAL (for manual transmission) and make sure the parking

brake is engaged.

Keep a fire extinguisher suitable for gasoline/chemical/ electrical

fires nearby.

Don’t connect or disconnect any test equipment while the

ignition is on or the engine is running.

Keep the scan tool dry, clean, free fromoil/water or grease. Use a

mild detergent on a clean cloth to clean the outside of the scan

tool, when necessary.

2. General Information

2.1 On-Board Diagnostics (OBD) II

The first generation of On-Board Diagnostics (called OBD I) was

developed by the California Air Resources Board (ARB) and

implemented in 1988 to monitor some of the emission control

components on vehicles. As technology evolved and the desire to

improve the On-Board Diagnostic system increased, a new generation

of On-Board Diagnostic system was developed. This second generation

of On-Board Diagnostic regulations is called "OBD II".

The OBD II system is designed to monitor emission control systems

and key engine components by performing either continuous or

periodic tests of specific components and vehicle conditions. When a

problemis detected, the OBD II system turns on a warning lamp (MIL)

on the vehicle instrument panel to alert the driver typically by the

phrase of “Check Engine” or “Service Engine Soon”. The system will

also store important information about the detected malfunction so

that a technician can accurately find and fix the problem. Here below

follow three pieces of such valuable information:

1) Whether the Malfunction Indicator Light (MIL) is

commanded 'on' or 'off';

2) Which, if any, Diagnostic Trouble Codes (DTCs) are stored;

3) Readiness Monitor status.

2.2 Diagnostic Trouble Codes (DTCs)

OBD II Diagnostic Trouble Codes are codes that are stored by the

on-board computer diagnostic system in response to a problem found

in the vehicle. These codes identify a particular problem area and are

intended to provide you with a guide as to where a fault might be

occurring within a vehicle. OBD II Diagnostic Trouble Codes

consists of a five-digit alphanumeric code. The first character, a letter,

identifies which control system sets the code. The other four

characters, all numbers, provide additional information on where the

DTC originatedand the operating conditions that caused it to set. Here

below is an example to illustrate the structure of the digits:

2.3 Location of the Data Link Connector (DLC)

The DLC (Data Link Connector or Diagnostic Link Connector) is the

standardized 16-cavity connector where diagnostic scan tools

interface with the vehicle's on-board computer. The DLC is usually

located 12 inches from the center of the instrument panel (dash),

under or around the driver’s side for most vehicles. If Data Link

Connector is not located under dashboard, a label should be there

telling location. For some Asian and European vehicles, the DLC is

located behind the ashtray and the ashtray must be removed to access

the connector. If the DLC cannot be found, refer to the vehicle’s

service manual for the location.

2.4 OBD II Readiness Monitors

An important part of a vehicle’s OBD II system is the Readiness

Monitors, which are indicators used to find out if all of the emissions

components have been evaluated by the OBD II system. They are

running periodic tests on specific systems and components to ensure

that they are performing within allowable limits.

Currently, there are eleven OBD II Readiness Monitors (or I/M

Monitors) defined by the U.S. Environmental Protection Agency

(EPA). Not all monitors are supported by all vehicles and the exact

number of monitors in any vehicle depends on the motor vehicle

manufacturer’s emissions control strategy.

Continuous Monitors -- Some of the vehicle components or systems

are continuously tested by the vehicle’s OBD II system, while others

are tested only under specific vehicle operating conditions. The

continuously monitored components listed below are always ready:

1）Misfire

2）Fuel System

3）Comprehensive Components (CCM)

Once the vehicle is running, the OBD II system is continuously

checking the above components, monitoring key engine sensors,

watching for engine misfire, and monitoring fuel demands.

Non-Continuous Monitors -- Unlike the continuous monitors, many

emissions and engine system components require the vehicle to be

operated under specific conditions before the monitor is ready. These

monitors are termed non-continuous monitors. For different ignition

type engines, the available monitors are different too.

The following monitors are to be used for spark ignition engines

only:

1) EGR System

2) O2 Sensors

3) Catalyst

4) Evaporative System

5) O2 Sensor Heater

6) Secondary Air

7) Heated Catalyst

The following monitors are to be used for compression ignition

engines only:

1) EGR System

2) NMHC Catalyst

3) NOx Aftertreatment

4) Boost Pressure System

5) Exhaust Gas Sensor

6) PM Filter

2.5 OBD II Monitor Readiness Status

OBD II systems must indicate whether or not the vehicle’s PCM’s

monitor system has completed testing on each component.

Components that have been tested will be reported as “Ready”, or

“Complete”, meaning they have been tested by the OBD II system.

The purpose of recording readiness status is to allow inspectors to

determine if the vehicle’s OBD II system has tested all the

components and/or systems.

The power-train control module (PCM) sets a monitor to “Ready” or

“Complete” after an appropriate drive cycle has been performed. The

drive cycle that enables a monitor and sets readiness codes to “Ready”

varies for each individual monitor. Once a monitor is set as “Ready”

or “Complete”, it will remain in this state. A number of factors,

including erasing of diagnostic trouble codes (DTCs) with a scan tool

or a disconnected battery, can result in Readiness Monitors being set

to “Not Ready”. Since the three continuous monitors are constantly

evaluating, they will be reported as “Ready” all of the time. If testing

of a particular supported non-continuous monitor has not been

completed, the monitor status will be reported as “Not Complete” or

“Not Ready.”

In order for the OBD monitor system to become ready, the vehicle

should be driven under a variety of normal operating conditions.

These operating conditions may include a mix of highway driving and

stop and go, city type driving, and at least one overnight-off period.

For specific information on getting your vehicle’s OBD monitor

system ready, please consult your vehicle owner’s manual.

2.6 OBD II Definitions

Power-train Control Module (PCM) -- OBD II terminology for the

on-board computer that controls engine and drive train.

Malfunction Indicator Light (MIL) -- Malfunction Indicator Light

(Service Engine Soon, Check Engine) is a term used for the light on

the instrument panel. It is to alert the driver and/or the repair

technician that there is a problem with one or more of vehicle's

systems and may cause emissions to exceed federal standards. If the

MIL illuminates with a steady light, it indicates that a problem has

been detected and the vehicle should be serviced as soon as possible.

Under certain conditions, the dashboard light will blink or flash. This

indicates a severe problem and flashing is intended to discourage

vehicle operation. The vehicle onboard diagnostic system can not turn

the MIL off until necessary repairs are completed or the condition no

longer exists.

DTC -- Diagnostic Trouble Code (DTC) that identifies which section

of the emission control system has malfunctioned.

Enabling Criteria -- Also termed Enabling Conditions. They are the

vehicle-specific events or conditions that must occur within the

engine before the various monitors will set, or run. Some monitors

require the vehicle to follow a prescribed “drive cycle” routine as part

of the enabling criteria. Drive cycles vary among vehicles and for

each monitor in any particular vehicle.

OBD II Drive Cycle -- A specific mode of vehicle operation that

provides conditions required to set all the readiness monitors

applicable to the vehicle to the “ready” condition. The purpose of

completing an OBD II drive cycle is to force the vehicle to run its

onboard diagnostics. Some form of a drive cycle needs to be

performed after DTCs have been erased from the PCM’s memory or

after the battery has been disconnected. Running through a vehicle’s

complete drive cycle will “set” the readiness monitors so that future

faults can be detected. Drive cycles vary depending on the vehicle and

the monitor that needs to be reset. For vehicle specific drive cycle,

consult the vehicle’s Owner’s Manual.

Freeze Frame Data -- When an emissions related fault occurs, the

OBD II system not only sets a code but also records a snapshot of the

vehicle operating parameters to help in identifying the problem. This

set of values is referred to as Freeze Frame Data and may include

important engine parameters such as engine RPM, vehicle speed, air

flow, engine load, fuel pressure, fuel trim value, engine coolant

temperature, ignition timing advance, or closed loop status.

3. Using the Scan Tool

3.1 Tool Description

1) CONNECTOR -- Connects the scan tool to the vehicle’s Data

Link Connector (DLC).

2) LCD DISPLAY -- Indicates test results. TFT color display (320

x 240 dpi).

3) FUNCTION BUTTON –Corresponds with “buttons”on

screen for executing commands.

Tabla de contenidos

Otros manuales de Equipo de prueba de Autel

Autel

Autel MaxiBAS BT608 Manual de usuario

Autel

Autel Autolink AL539B Manual de usuario

Autel

Autel MaxiPRO MP808S Manual de usuario

Autel

Autel MaxiBAS BT609 Manual de usuario

Autel

Autel EVO NEST Manual de usuario

Autel

Autel Autolink AL619 Manual de usuario

Autel

Autel AutoLink AL419 Manual de usuario

Autel

Autel MaxiSys SCR Manual de usuario

Autel

Autel MaxiLink ML609P Manual de usuario

Autel

Autel MaxiDAS DS808TS Manual de usuario

Autel

Autel MaxiLink ML529 Manual de usuario

Autel

Autel MaxiBAS B200 Manual de usuario

Autel

Autel AutoLink AL529 Manual de usuario

Autel

Autel MaxiCheck MX900 Manual de usuario

Autel

Autel MaxiBas BT508 Manual de usuario

Autel

Autel MaxiPRO MP808TS Manual de usuario

Autel

Autel AutoLink AL529 Manual de usuario

Autel

Autel MaxiTPMS TS601 Manual de usuario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario