Autel Robotics Dragon Fish Manual de usuario
Dragon Fish Mobile Station
Quick Guide
Disclaimer
To ensure safe and successful operation of your base station, please strictly follow the
operating instructions and steps in this manual.
If the user does not abide by the safety operation instructions, DTO Smart will not be
responsible for any product damage or loss during use-whether direct or indirect,
legal, special, accident or economic loss (including but not limited to loss of profit)-
Provide warranty service. Do not use incompatible parts or use any method that does
not comply with the official instructions of Autel Smart to modify the product.
The safety guidelines in this manual will be updated from time to time. To ensure that
you get the latest version, please visit www.auteldrones.com/support/downloads/
battery safety
Dragon Fish base preclude the use of lithium polymer batteries. Improper use of
lithium polymer batteries can be dangerous. Please ensure that all the following
battery usage, charging and storage guidelines are strictly followed.
Warning
●Only use the battery and charger provided by DTO Smart. It is prohibited to
modify the battery pack and its charger, or use third-party equipment to replace
it.
●The electrolyte in the battery is extremely corrosive. If the electrolyte accidentally
spills into your eyes or skin, please wash the affected area with clean water
immediately and seek medical attention.
Precautions
1. According to local radio regulations, use base stations with corresponding
frequency bands and comply with local radio laws and regulations.
2. Do not excessively bend and fold the wire during installation.
3. When installing and placing, make sure that the base station is level with the
horizontal plane.
4. Use the base station in an open environment free from radio interference. Be sure
to turn off other wireless devices in the same frequency band before using it.
5. Please make sure that the antennas of all devices are not blocked during use.
6. Use original accessories or accessories certified by Autel. The use of non-original
accessories may cause danger to the safe use of the system.
7. Make sure that no foreign objects (such as water, oil and other liquids, sand, etc.)
enter the parts.
8. Do not remove any parts installed at the factory by yourself.
9. When using in rain or snow, please take necessary waterproof measures for the
base station. Please use caution in thunder and lightning weather and pay
attention to lightning protection.
Introduction
Dragon Fish GNSS base station (hereinafter referred to as "base station") is a high-
precision satellite signal receiver that supports 11-frequencyGPS, Beidou, Galileo and
GLONASS navigation systems1satellite signal reception of, as well as built-in carefully
tuned data transmission The system is convenient for users to use in different
application environments.
Dragon Fish GNSS base station as RTK base station, so that the positioning accuracy
Dragon Fish centimeter, but also provides a powerful magnetic immunity, protection
and reliable flight operations at ambient power lines, metal construction and other
magnetic interference.
Item list
serial
num
ber
picture name quantity
1
base station
(including base
station cover)
1 PCS
2
base station chassis 1
3
base station tripod 1
4
base station feeder 2
5
base station
antenna 2
6
multi-function
charger
1 PCS
7
TYPE-
C charging
cable 1 PCS
8
Document
(Quick Guide) 1
component description
base station body
1. Linking indicator
2. WiFi indicator
3. RTK indicator
4. Power indicator
5. USB-C charging port
6. Linking button
7. Power button
8 Port cover
9. Antenna N-type connector
10. Turntable mounting hole
11. Heat sink
tripod
1. Fixing screw
2. Knob
3. Telescopic pole
4. Foot nail
ready for
charging
Short press (<1 second) the power button once to check the battery level.
Description of power indicator
Green: Electricity>60%
Yellow: Electricity>30%
Red: Electricity>10%
Red flashing slowly: Electricity <10%
charging method charge
When using thefor the first time, be sure to fullythe battery. Please use a dedicated
charger to charge the base station.
1、Plug the Type-C power cord into the Type-C port of the base station, and the base
station will automatically enter the charging mode (either when it is turned on or
off).
2、When charging, the base station power indicator light flashes, and the battery
power is indicated by different colors. When connected to a charging power
source, the base station power indicator light is steady green to indicate that it is
fully charged.
Turn on/off the base station
Turn on
The base station has 2 working modes, namely normal mode and disabled RTK mode,
which can be used in different operating scenarios. Follow the instructions below to
turn on the base station and enter different working modes.
1. When the base station is off, press and hold the power button for 1 second to enter
the normal mode.
2. When the base station is off, press and hold the power button for 3 seconds to
enter the disabled RTK mode. When entering, the buzzer will beep 3 times and the
RTK indicator will be steady red.
Turn off
Long press the power button for 1 second to turn off the
RTK indicator light Description
Green: Number of satellites>16, good signal (normal flight)
Yellow: Number of satellites 6-15, poor signal (it is recommended to adjust the base
station to an open area)
Red Slow flashing: number of satellites <6, poor signal (recommend the base station
to be placed in an open area)
Light off: no RTK signal (indoors or abnormal base station RTK)
use to
connect to a ground station or aircraft
connection method
Take the normal mode as an example, the specific operation is as follows.
To link the base station and the aircraft link
1、click thebutton of the base station, and the linking light flashes;
2、press (short press) the linking button in the battery compartment of the aircraft to
make the aircraft enter the linking state, and the linking light of the aircraft body
flashes during the linking process ;
3、After successful linking, the linking light on the base station will flash green for
0.1s/2.0s.
Connect the ground station to the base station
1、turn on the power of the station;
2、turn on the remote control and run the Autel Voyager App, select "Settings ->
Base Station", you can see the base station wifi hotspot after entering, enter the
password: 12345678, wait a few seconds until the remote control is successfully
connected to the base station;;
3、exit Setting interface, enter the mission flight interface, click the gear icon in the
upper right corner, enter the settings menu, click "remote control", and turn on
the "use base station connection" option.
Link the ground station and the aircraft
1、Press (short press) thebutton in the battery compartment of the aircraft to enter
the state;
2、linkingopen the remote control and run the Autel Voyager App to enter the
mission flight interface, and click the gear icon in the upper right corner , Enter the
setting menu, click "remote control -> data and video linking -> start linking", wait
a few seconds until linking is successful.
Description of thetransmission status indicator:
videoGreen 1.5s/1.5s blinking slowly:transmission is not connected,
green light 0.1s/0.1s blinking fast:
videovideo transmission is linking,light 0.1s/2.0s blinking: video transmission is
normally connected,
greengreen light 3s /0.2s flashing on and off: Upgrade download data installed during
Green light on: firmware upgrade
Dragon Fish GNSS base station is
Choose a place with a wide view to set up the Dragon Fish GNSS base station and
mark it (align the center of the tripod with the center of the mark point) so that the
base station can be accurately reset after being moved.
1. Open the tripod, stretch the three telescopic rods to a suitable length, and then
tighten the knob to ensure that the tripod is stable.
Otros manuales para Dragon Fish
3
Tabla de contenidos
