Aussie Fit E9500 Manual de usuario
Aussie Fit E9500
Recumbent BIKE
OWNER’S MANUAL
IMPORTANT: Read all instructions carefully before using this product. Retain this
owner’s manual for future reference.
The specifications of this product may vary from this photo, subject to change without
notice.
SAFETY INSTRUCTIONS
Basic precautions should always be followed, including the following safety
instructions when using this equipment: Read all instructions before using this
equipment.
1. Read all the instructions in this manual and do warm up exercises before using this
equipment.
2. Before exercise, in order to avoid injuring the muscle, warm-up exercise of every
position of the body is necessary. Refer to Warm Up and Cool Down Routine page.
After exercise, relaxation of the body is suggested for cool-down.
3. Please make sure all parts are not damaged and fixed well before use. This
equipment should be placed on a flat surface when using. Using a mat or other
covering material on the ground is recommended.
4. Please wear proper clothes and shoes when using this equipment; do not wear clothes
that might catch any part of the equipment.
5. Do not attempt any maintenance or adjustments other than those described in this
manual. Should any problems arise, discontinue use and consult an Authorized
Service Representative.
6. Be careful when step on or leave the pedal always hold the handlebars first. Make the
pedal at your side at the lowest position, step on the pedal, and stride over the main
frame then step on the other pedal. When using, please hold the handlebar by hands,
make the pedals running smoothly by push or pull handlebars, then run the equipment
regularly by cooperation of hands and feet. After exercise, please also make one
pedal at the lowest position and leave your foot on the higher pedal first and then
another.
7. Do not use the equipment outdoors.
8. This equipment is for household use only.
9. Only one person should be on the equipment while in use.
10. Keep children and pets away from the equipment while in use. This machine is
designed for adults only. The minimum free space required for safe operation is not
less than two meters.
11. If you feel any chest pains, nausea, dizziness, or short of breath, you should stop
exercising immediately and consult your physician before continuing.
12. The maximum weight capacity for this product is 135kgs.
WARNING:Before beginning any exercise program consult your physician.
This is especially important for the persons who are over 35 years old or who have
pre-existing health problems. Read all instructions before using any fitness
equipment.
CAUTION:Read all instructions carefully before operating this product.
Retain this Owner’s Manual for future reference.
PARTS LIST
No.
Description
Qty
No.
Description
Qty
001
Main Frame
1
031
Eccentric shaft Φ26x41
1
002
Front Stabilizer
1
032
Skate brake
1
003
Rear Stabilizer
1
033
Crash pad 40.8X28.5X6.1
1
004
Sliding tube assembly
1
034
Brake decorative covers
1
005
Sliding sleeve assembly
1
035
Bolt M5x10
6
006
Back/Seat Support Bracket
1
036
Inside hexagonal Bolt M6x15
2
007
Rear Handlebar
1
037
Outer hexagonal Bolt M6x15
1
008
Brake handle support
1
038
Draw spring
1
009
Brake handle
1
039
Nut M6
1
010
Bolt M8x50
2
040
Bolt M8x20
4
011
Spring washerФ8
8
041
Big Washer Ф8XФ20x2.0
4
012
Curve washerФ8xФ16x2.0
2
042
Crash padφ25*10-M8*10
4
013
Handlebar Foam Grip
Φ31xΦ37x520
2
043
Flexible wire L=1700mm
1
014
Circular tube plugФ32x1.5
2
044
Plug
1
015
Hand Pulse Sensor with Wire
(L=750mm)
2
045
Bolt M8x90
4
016
Bolt ST4.2x20
3
046
Curve washerФ8xФ20x2.0
4
017
Seat Cushion
1
047
Cap Nut M8
4
018
Back Cushion
1
048
Adjust the foot pad M10
5
019
Bolt M8x45
4
049
Nut M10
5
020
Washer Ф6
8
050
Circular tube plugФ76x2
4
021
Round Knob
1
051
Left Rear Main Frame Cover
1
022
Plastic sleeveФ38xФ19x20
2
052
Right Rear Main Frame Cover
1
023
Bushing
2
053
Screw ST4.2x20
16
024
Nut cap S13
2
054
Screw ST4.2x25
10
025
Bolt M8x15
2
055
Rubber Sleeve
5
026
Big Washer Ф8XФ25x2.0
2
056
Motor
1
027
Spin axis
1
057
Sensor Extension Wire
(L=1100mm)
1
028
Bolt M6x20
4
058
Sensor with Wire (L=450mm)
1
029
Circlip
2
059
Bolt ST2.9x12
2
030
Plastic sleeveФ29x9.2
2
060
Limit file piece
4
PARTS LIST
No.
Description
Qty
No.
Description
Qty
061
Bolt M5x15
4
081
Bolt M6x15
4
062
WasherΦ5
4
082
Belt
1
063
Computer
4
083
Flywheel
1
064
Computer support
1
084
Nut M10x1.0x6
2
065
Left Pedal
1
085
Big Washer Ф30x10.5
2
066
Right Pedal
1
086
Motor Tension Cable L=500mm
1
067
Cover Cap
2
087
BoltФ8x31
2
068
Nut M10x1.25
2
088
Bearing 608
4
069
Left crank
1
089
Roller
2
070
Right crank
1
090
Bolt M6x12
2
071
Cank Cover
2
091
Power supply wire L=550mm
1
072
Left Chain Cover
1
092
Nut M12
1
073
Right Chain Cover
1
093
AC Adapter wire L=2000mm
1
074
CirclipΦ20
2
075
Wave spring washer
1
076
Bearing
2
077
Nut M6
4
078
Spring Washer Ø8
4
079
Belt Pulley with Crank
1
080
Straight spindle assembly
1
4
HARDWARE PACKING LIST
OVERVIEW DRAWING
ASSEMBLY INSTRUCTIONS
1. Front and Rear Stabilizer Installation
A.Position two Foot Pad(48) onto the Front Stabilizer (2)
B.Position two Foot Pad(48) onto the Rear Stabilizer (3)
C.Position the Front Stabilizer (2) in front of Main Frame (1) and align bolt holes.
Attach the Front Stabilizer (2) onto the front curve of the Main Frame (1) with two M8x90
Bolts (45), Ø8xØ20x2.0 Curve Washers (46) and M8 Cap Nut (47).
D.Position the Rear Stabilizer (3) in front of Main Frame (1) and align bolt holes.
Attach the Rear Stabilizer (3) onto the front curve of the Main Frame (1) with two M8x90
Bolts (45), Ø8xØ20x2.0 Curve Washers (46) and M8 Cap Nut (47).
2. Pedal and brake handle Installation
Important:
Make sure the RIGHT pedal matches up with the RIGHT crank and the LEFT pedal matches
up with the LEFT crank.If reversed the cranks may become damaged or stripped.
A. Left Pedal Installation:Insert the Left Pedal(65) into the threaded hold in the Left
Crank(69). Turn the pedal shaft by hand in a counter-clockwise direction and tighten
suing the multi Hex Tool with Phillips Screwdriver.
B. Right Pedal Installation:Insert the Right Pedal(66) into the threaded hold in the Left
Crank(70). Turn the pedal shaft by hand in a counter-clockwise direction and tighten
suing the multi Hex Tool with Phillips Screwdriver.
C. Remove two M6x15Bolts(36)from the brake handle support(9),attach the brake handle(8)
onto the brake handle support(9) with M6x15Bolts(36) that were removed.
D. Attached two S13 Cap Nut (24) onto the Back/Seat Support Bracket(6) Left and Right.
3. Seat Cushion Installation
Remove four Bolt M6x20(28) and four Flat WasherΦ6(20) from
Seat Cushion (17).
Then attach the Seat Cushion (17) onto the Seat Support
Bracket (5) with four Bolt M6x20(28) and four Flat WasherΦ
6(20) that were removed.
4. Back Cushion Installation
Remove four Bolt M6x45(19)and four Flat Washer
Φ6(20) from Back Cushion(18). Then attach the
Back Cushion (31) onto the Back Support Bracket
(6) with Bolt M6x45(19)and four Flat WasherΦ
6(20) that were removed.
5. Handlebar Installation
Attach the Rear Handlebar (7) onto the Seat Support
Bracket (5) with two M8x50mm Bolts (10), two Ø8
Spring Washers (11) and two Ø8xØ16x2.0 Curve
Washers (12).
Connect the Flexible wire (43) from the Main Frame
(1) to the Hand Pulse Sensor Wires (15)from the
Rear Handlebar (7).
6. Computer Installation
A.Remove four Screw M5x10(35) from computer (63). Attach the Computer (63) onto the
Computer support (64) with four Screw M5x10(35) that were removed.
B.Remove four screw M5x15(61)
and four washer washer Ø5 (62)
from the Computer support (64).
Connect Flexible wire (43) and
Sensor Extension Wire (57) from the
Main Frame (1) to the wires that
come from the Computer (63) and
then attach the Computer (63) onto
the top end of the Main Frame (1)
with four screw M5x15(61) and four
washer washer Ø5 (62) that were
removed.
Tabla de contenidos
Otros manuales de Bicicleta estática de Aussie Fit
