Aurora Lite Bank FRECON2 Manual de usuario

11



11

Thank you for your purchase.

FRECON2 can be used to wirelessly synchronize the ﬂash lights with the

camera and to remotely control any of the ﬂash lights with built-in

FROCON2 radio system, including ﬂash power control and modeling light

control. FRECON2 also features a co-channel relay function, the perfect

solution for triggering a remote camera in sync with remote ﬂash lights.

Please read this user manual as well as the user manual provided with

your camera and ﬂash light which works with FRECON2 before use.

For your safety

Before using your product, please read the following safety precaution

carefully to ensure correct and safe use.

Do not disassemble or attempt to repair it.

Do not use the product in the presence of ﬂammable or explosive gas.

The product is not waterproof. Please keep away from rain, snow and high

humidity conditions.

Do not expose the product to high temperature over 45°C (e.g. left in a car

trunk).

Do not clean the product with organic solvent or alcohol-based liquid.

A thorough explanation of how to use the product by an adult is required

when the product is used by children. Supervise children while they are

using the product.

Consult local authorities on the proper disposal or recycling of a battery.

·1·

·2·

RED 2014/53/EU

Declaration of Conformity EC

Hereby, Aurora Lite Bank Co., Ltd. declares that this product is in compliance

with essential requirements and other relevant provisions of Directive

2014/53/EU. This product can be used with EU member states.

FCC Statement

FCC ID: 2AEJW-E2

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

Company name : AURORA LITE BANK Co., Ltd.

Equipment Name : FRECON2 transceiver

Model Name : FRECON2

Manufactured Date : AUGUST /2020

Manufacturer / Country : AURORA LITE BANK Co.,

Ltd. / CHINA

R-CS-XXX-YYYYYYYYYYYYYY

television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or

more of the following measures;

Reorient or relocate the receiving antenna.

Increase the separation between equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

Consult the dealer or an experience radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly

approved by manufacturer could void your authority to operate this

equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to

the following two conditions; (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

RF Exposure information

The device has been evaluated to meet general RF exposure requirement.

The device can be used in portable exposure condition without restriction.

CAUTION

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT

TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE

INSTRUCTIONS.

·3·

·4·

I. Parts 

II. Getting Started 

Installing the batteries 

Turning FRECON2 on/oﬀ 

Connecting to the camera 

III. States and Modes 

IV. Basic Functions and Buttons 

State and Mode Adjustment 

Channel Selection 

Group Selection 

Remote Control ‒ Head Control; Model Control; Energy Adjustment 

Master Mode 

Command Conﬁrmation 

Test Function 

Slave Button 

Alarm Button 

Beeper Button 

Auto Power Oﬀ 

Factory Settings 

V. Operating Instructions 

Remote Flash Synchronization 

Release of Remote Camera 1

Relay 

VI. Speciﬁcations 

Table of Contents

I. Parts (Figure1)

Channel Indicators (1-8)

Channel Button

Group Indicators (A-F)

Group Button

Energy Adjustment Buttons

<+> Increase, <-> Decrease

Head Control Button

Slave Button

Model Control Button

Alarm Button

Command Indicator

Power Button

Master Button

Test Button

Beeper Button for FRECON2

Mode Indicators

(TRANSMIT, RECEIVE)

Mode Adjustment Button

USB Port

In Port (3.5mm)

Out Port (3.5mm)

Mounting Foot Lock Lever

Hot Shoe Mounting Foot

10.

11.

12.

13.

14.

15.

16.

17.

18.

19.

20.

21.

17 18

(Figure1)

·5·

II. Getting Started

Installing the batteries (Figure 2)

Via hot shoe (Figure 3)

Turning FRECON2 on/oﬀ

Connecting to the camera

1. Open the battery cover from the back of FRECON2.

2. Install 2 AAA batteries in accordance with the illustrated direction inside

the battery compartment.

3. Close the battery cover in place.

1. Turn on: Press the Power Button (11) to turn on the FRECON2, the

Channel indicator (1) and Group indicator (3) light up.

2. Turn oﬀ: Press and hold the Power Button (11) until all indicators light oﬀ.

1. Turn oﬀ the camera and FRECON2.

2. Slide the Hot Shoe Mounting Foot (21) of the FRECON2 into the

camera’s hot shoe mount.

3. Lock the FRECON2 by sliding the Mounting Foot Lock Lever (20) to the

right until the lock lever clicks in place.

4. Turn on the camera and FRECON2 and the shooting mode of the camera

to manual.

(Figure 2)

·6·

Via Flash Sync Cable (3.5mm - PC, Sold seperately) (Figure 4)

5. To detach FRECON2, press the lock-release button on the Mounting

Foot Lock Lever (20) while slide the lock all the way back to the left, then

slide the FRECON2 out of camera’s hot shoe mount.

1. Turn oﬀ the camera and FRECON2.

2. Insert the 3.5mm Plug of the ﬂash sync cable into the in Port (18) of

FRECON2.

3. Insert the PC Plug of the ﬂash sync cable into the PC terminal of the

camera. For proper connection with the camera or ﬂash light, consult

the user manual of the actual camera or ﬂash light at the same time.

4. Turn on the camera and FRECON2 and set the shooting mode of the

camera to manual.

(Figure 3)

·7·

III. States and Modes

FRECON2

Standard State

Transmit Mode

Receive Mode

Transmit Mode

Receive Mode

Relay State

1. The following states and modes are available in FRECON2.

2. Select the appropriate state and mode as described in this manual in

actual use.

·8·

Tabla de contenidos

Manuales populares de Accesorios para cámaras de otras marcas

Viltrox

Viltrox EF-NEX Instrucciones de instalación

Calumet

Calumet 7100 Series CK7114 Manual de usuario

Ropox

Ropox 4Single Series Manual de usuario

Cambo

Cambo Wide DS Digital Series Instrucciones de funcionamiento

Samsung

Samsung SHG-120 Manual de usuario

Ryobi

Ryobi BPL-1820 Manual de operación

Aegis

Aegis ABL-36020P Manual de usuario

Pentax

Pentax Data Back Fc Manual de usuario

Fantasea

Fantasea EyeGrabber F Series Manual de usuario

Honeywell

Honeywell HDZ20HD Manual de usuario

EGO

EGO BA1400T Manual de usuario

Sima

Sima SRW-62 Manual de usuario

Shape

Shape A7SSMKIT Manual de usuario

Slide Kamera

Slide Kamera HST-2 Manual de usuario

Power works

Power works 2902613 Manual de usuario

SES

SES SE-2047-2 Manual de usuario

Olympus

Olympus PT-EP05L Manual de usuario

Starlite

Starlite OctoDome nxt Manual de usuario