Aura AMH-210BT Manual de usuario
OWNER’S MANUAL
AMH-220BT
AMH-230BT
AMH-215BT
AMH-210BT
WARNING!
PLEASE READ CAREFULLY BEFORE USING
CAR BLUETOOTH / USB RECEIVER
1
Àâòîðñêèå ïðàâà
All illustrations in this manual are schematic images of objects and may differ
slightly from their real appearance.
Product service life - 3 years.
All brand and product names used in this document are trademarks or
registered trademarks of their respective companies.
is a registered trademark. All rights reserved. This
document in whole or in part may not be reproduced or copied without
the prior written permission of the manufacturer.
In order to improve product quality, product specifications and
features are subject to change without notice.
Trademarks and product names are used for editorial purposes only
and for the benefit of such companies only.
The manufacturer does not accept any responsibility for the use of this
manual and decisions based on its use.
The Directive WEEE 2012/19/EU on waste electrical and electronic
equipment.
Waste electrical equipment should not be disposed of with your other
household waste. Please recycle it. Please contact your local authority
for the required information.
Precautions...........................................................................................
Complete set and installation ..............................................................
Connection ..........................................................................................
Appearance, controls ..........................................................................
Dimensions...........................................................................................
Basic Operation ...................................................................................
Radio.....................................................................................................
USB ......................................................................................................
Bluetooth ..............................................................................................
Smartphone application .......................................................................
Specifications........................................................................................
Warranty card .......................................................................................
3
4
5
6
7
8
9
9
10
11
12
13
2
Content
1. While installing the device, avoid places with high temperature, humidity, or
dusty places.
3. Do not drop the device and make sure do not hit it, as this may damage it.
This user manual contains important safety advice and information on the correct
use of the device. Please follow all instructions in this manual carefully.
4. The manufacturer will not be held liable for any loss of data caused by device
damage, repairs or any other reason.
2. Make sure that the device and especially its installation accessories are out of
the reach of children.
7. Avoid contact with liquids.
5. Do not disassemble the device yourself. This may void the warranty.
8. The product is designed for use with 12-volt negative-grounded electrical
systems only. Using the device on systems with a positive ground and / or
voltage other than 12 volts may damage the vehicle and the device.
6. Do not use alcohol, solvents or gasoline for cleaning plastic parts and device.
Use only dry soft cloth for cleaning.
3
Precautions
4
Open the package and make sure that it contains:
1. BT / USB receiver - 1pc.
2. Keys for removing the receiver - 2 pcs.
3. ISO connector - 1 pc.
4. Instruction
If the car has a standard 1DIN hole for installing the head unit, use it as
described below.
Package bundle and installation
1DIN hole
2. Use a screwdriver to pry out the metal tabs on the mounting cover to lock it
in place.
4. Connect the ISO connector to the device. And check the functionality of the
system before fixing it in the mounting box.
If necessary, use ISO adapters brand
3. Check electrical connections, ISO connector or individual wires (depending
on the equipment of the specific car model).
1. Install the mounting cover into the 1DIN hole provided by the manufacturer. If
the standard place has a 2DIN size, use adapter frames and adapters
brand
5. Insert the device into the mounting cover and slide it inward until it clicks into
place.
1. Make sure that the on-board voltage of your vehicle is +12 volts
4. Connect the red wire (A7) to the ACC terminal of the ignition switch.
6. Blue wire (A5) - Connect to the amplifier's remote turn-on input or the antenna motor control
input.
5. Connect the black wire (A8) to the metal part of the car body.
8. Connect the rest of the wires according to the diagram.
2. Remove the fuse from the device before connecting the wires.
7. Connect the orange wire (A6) to the circuit where +12 volts appears when the dimensions are
turned on.
Note: Each time the yellow wire is disconnected from the 12 volt power circuit or the battery
terminal is removed, the device will revert to factory settings.
3. Connect the yellow (A4) wire to the +12 Volt DC power circuit.
B3 Right channel + (gray)
Rear speakers
B1 Right channel + (purple)
B2 Right channel - (purple-black)
B4 Right channel - (gray-black)
B8 Left channel - (green-black)
B5 Left channel + (white)
B7 Left channel + (green)
Front speakers
B6 Left channel - (white-black)
WARNING
DO NOT OPEN
5
Radio antenna connection input
RCA front – Left (white)
RCA rear – Right (red)
RCA rear – Left (white)
RCA front – Right (red)
10 A
fuse
A5 + 12V control wire to control the motorized antenna
and remotely turn on / off amplifiers or other active
auxiliary devices.
A7 ACC + 12V DC wire - Connect to a power source
that can be turned on and off from the car ignition
switch.
A6 Dimmer. Connection to vehicle lighting control.
A4 Battery + 12V DC
+12 VDC - connect to the remote turn-on input of the
amplifier or the antenna motor control input (no more
than 100 mA, 12 V).
A8 Minus (ground) - connect to a metal part
RED
ACC +12V
YELLOW
constant
power
+12V
BLACK
ground
MINUS
BLUE
control
wire
+12V
Connection
6
1
2
3467
8
9
11
12
13 14 15 16
17
18
5
AMH-230BT
3
12 13 14 15 1618
8
13
46
717
5
2 9
10 11
19
3. Volume control / select button (SEL).
6. Preset button 3 / Repeat button.
8. Mute button.
5. Preset button 2 / Record scan button.
9. Button for selecting radio frequency range / autosearching stations (BND / AMS).
4. Preset button 1 / play / pause button.
2. Fast forward / select next song / accept call.
7. Liquid crystal display.
1. Button on. / off. nutrition. Source selection.
10. Source selection (AMH-230BT)
11. Button rewind / select the previous track / end call.
12. Preset button 4 / Shuffle button.
13. Preset button 5 / previous folder / down for 10 tracks.
14. Preset button 6 / next folder / up 10 tracks.
17. USB port.
19. Equalizer selection button.
16. AUX-IN jack.
15. Slot for SD memory card.
18. Button for setting hours.
AMH-220BT
2
8 9
11 12 13 14 15
1618
13
46
717
5
AMH-210BT
AMH-215BT
SD
Control elements
7
80
32,5 38
188
178
182
53
50
58
Overall sizes,mm
80
32,5 38
184
178
182
53
50
54
Model: AMH-210BT, AMH-215BT, AMH-220BT
Model: AMH-230BT
8
ON / OFF Power
Press any button to turn on the device.
Press and hold the button (1) /SRC, to turn on the device.
Source selection
Press the (1) / SRC button to switch between sources
playback: Radio -> USB -> AUX in -> Bluetooth.
Adjusting the sound parameters
Press the (3) SEL button on the front panel to select sound adjustment options.
The parameters are selected in the following sequence:
Volume -> BASS (bass) -> TRE (treble) -> BAL (left / right balance) ->
FAD (front / rear balance) -> EQ (equalizer setting) ...
Turn the volume knob (3) to adjust the selected parameter.
EQ - equalizer setting
Equalizer Presets: JAZZ / CLASS / ROCK / POP / USER
Radio
Range selection
Press the button (9) BND/AMS, to select the broadcast range radio
stations: FM1, FM2, FM3.
Saving and recalling radio stations
Press and hold one of the number buttons (1-6) to store the current radio station.
Press one of the number buttons (1-6) to recall the current radio station.
It is possible to store 6 radio stations in each broadcasting range.
Automatic station search
Press the (2) or (11) button to quickly search for stations.
Main functions
Volume control
Rotate the volume knob (3) to set the desired level.
9
Radio
Search and store stations automatically
Press and hold the button (9) BND/AMS more than 2 seconds.
The unit will quickly search for and automatically store 18 FM radio
stations with strong signals.
Manual station search
Press and hold more than 2 seconds the button (2) or (11) , to enter
manual tuning mode.
Press the button (2) or (11) , to change the frequency step by step.
Hold the button (2) or (11) , to change the frequency step by step.
USB
Connect a USB storage device to the connector on the front of the device.
Supported file formats will start playing automatically.
The USB connector supports charging mobile devices. Charging current - up to 1A.
Switching tracks
Press the button (2) or (11) to skip to the previous or next track.
Rewind
Press and hold the button (2) or (11) to rewind or fast forward.
Play / pause
Press the button (4) to stop playback.
Press again to resume playback.
Track scanning
Press the button (5) INT for sequential playback of 10 seconds of each track.
Click again to stop scanning.
Repeat play
Press the button (6) RPT, to select the repeat play mode.
Shuffle play
Press the button (12) RDM to turn on the random play mode.
Press again to disconnect.
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Receptor de coche de Aura
