Auer HTi70 6 Manual de usuario

Made in

France

Manual ref.: 1898536

Edition no22.39

Installation and User manual

HTi70

High temperature, ultra modulating

Heat pump

HTi70 6kW single-phase

Ref. 155000

HTi70 8kW single-phase

Ref. 155010

HTi70 8kW three-phase

Ref. 155050

The information contained in this document is non-contractual. The manufacturer reserves the right to modify any technical specifications and equipment of any appliances without prior notice.

* Concerns HTi70 6 and 8 single-phase models

- MANUAL HTi70 6 & 8 KW HEAT PUMPS -

TABLE OF CONTENTS

1-SAFETY ............................................................. 4

2 -PLEASE READ IMMEDIATLY ........................... 5

2.1 - Conservation of documents ............................................................5

2.2 - Symbols used........................................................................................5

2.3 - Abbreviations and acronyms...........................................................5

2.4 - Certication «Origine France Garantie» ..........................................5

3 - DELIVERY AND STORAGE............................. 6

3.1 - Delivery terms and conditions........................................................6

3.1.1 - HTi70 6 & 8kW.............................................................................................................. 6

3.2 - Storage and transport........................................................................6

3.2.1 - General information ................................................................................................6

3.2.2 - Transporting with a forklift .................................................................................. 6

3.2.3 - Transporting manually............................................................................................6

4 - INTRODUCTION............................................. 7

4.1 - Operation................................................................................................7

4.2 - Accessories (included) .......................................................................7

4.3 - Accessories available to order.........................................................7

5 - INSTALLATION................................................ 8

5.1 - Standard conguration .....................................................................8

5.2 - Placement...............................................................................................9

5.2.1 - Noise levels................................................................................................................. 9

5.2.2 - Safe area.......................................................................................................................9

5.2.2.1 - Ground security area ..............................................................................9

5.2.2.2 - Security area in front of a wall...........................................................10

5.2.3 - Accepted installation sites ..................................................................................10

5.2.4 - Prohibited installation sites ................................................................................10

5.3 - Setting up.............................................................................................11

5.3.1 - Condensates drainage..........................................................................................11

5.4 - Hydraulic installation........................................................................12

5.4.1 - Hydraulic connections on the installation ....................................................12

5.4.2 - Hydraulic connection between Heat pump and pilot.............................13

5.4.3 - Heat pump water inlet lter (supplied)..........................................................13

5.5 - Connecting to the power supply.................................................13

5.5.1 - General recommendations.................................................................................13

5.5.2 - Accessing the connection terminals ...............................................................14

5.5.3 - Recommendations for connecting the system to the power supply..14

5.5.4 - Connection to the power supply......................................................................14

5.5.4.1 - Single-phase connection ....................................................................14

5.5.4.2 - Three-phase connection .....................................................................15

5.5.5 - Communication bus cable between the heat pump and the pilot......15

6 - MAINTENANCE AND TROUBLESHOOTING16

6.1 - General information .........................................................................16

6.2 - Maintenance on the hydraulic circuit.................................................16

6.3 - Maintenance of the Heat pump...................................................16

6.4 - Maintenance of the electrical components..........................................16

6.5 - Consulting the meters .....................................................................16

6.6 - Sensor data curve charts.................................................................17

6.6.1 - Water inlet and outlet - de-icing sensor

- Air intake sensor

- Sensors installed on compressors 1 and 2 -.............................................................................17

6.7 - Modication.........................................................................................17

6.8 - Decommissioning..............................................................................17

6.8.1- Interim Decommissioning of Product..............................................................17

6.8.2- Final decommissioning of the product ...........................................................17

6.9 - Recycling and Disposal....................................................................17

6.9.1- Disposal of refrigerant ...........................................................................................17

7 - LIST OF SPARE PARTS..................................18

8 - WARRANTY ................................................... 19

8.1 - Warranty coverage ............................................................................19

8.2 - Limitations of warranty....................................................................19

8.2.1 - General information ..............................................................................................19

8.2.2 - Cases (not limited to) for exclusion from warranty ....................................19

8.2.2.1 - Heating circuit water ............................................................................19

8.2.2.2 - Handling....................................................................................................19

8.2.2.3 - Installation site........................................................................................19

8.2.2.4 - Electrical connections ..........................................................................19

8.2.2.5 - Hydraulic connections .........................................................................19

8.2.2.6 - Accessories...............................................................................................19

8.2.2.7 -Maintenance.............................................................................................19

APPENDIX ..........................................................20

A1 - Technical specications....................................................................20

A1.1 - General characteristics..........................................................................................20

A1.2 - Performances............................................................................................................20

A2 - EU declaration .....................................................................................21

A3 - Frost protection ..................................................................................21

A4 - Treatment of the water in the heating circuit..........................21

A4.1 - Preparing the hydraulic circuit (rinsing) .........................................................21

A4.2 - Filling water..............................................................................................................21

A4.3 - Treatment of the heating circuit........................................................................21

A5 - Dimensions...........................................................................................22

A5.1 - HTi70 6 kW Heat pump...........................................................................................22

A5.2 - HTi70 8 kW Heat pump...........................................................................................23

- MANUAL HTi70 6 & 8 KW HEAT PUMPS -3

A6 - Product technical information sheet ..........................................24

A6.1 - HTi70 6 kW Heat pump...........................................................................................24

A6.2 - HTi70 8 kW single-phase Heat pump.................................................................25

A6.3 - HTi70 8 kW three-phase Heat pump..................................................................26

A7 - Internal wiring diagram ...................................................................28

A7.1 - HTi70 6 & 8 kW single-phase Heat pump.........................................................28

A7.2 - HTi70 8 kW three-phase Heat pump..................................................................29

NOTES / MAINTENANCE ................................... 30

- MANUAL HTi70 6 & 8 KW HEAT PUMPS -

1-SAFETY

Danger resulting from improper qualications

• Any work carried out by an unqualied person

can result in damage to the installation or in

physical injury.

• Do not perform maintenance on this appliance

unless you are a qualied professional.

• If the appliance is malfunctioning or not

working, cut the electricicty supply to the

electrical components and seek advice from a

qualied professional.

Danger resulting from improper use

This appliance should not be used by anyone

(including children under the age of 8 years

old)with reduced physical, sensory or mental

capabilities, or by anyone with insufficient

experience or knowledge of the appliance; unless

they are being supervised by someone who is

responsible for their safety and in possession of

the operating instructions of the appliance, or if

they have been instructed in the proper use and

in the risks of operating the appliance.

Children must not play with the appliance.

Cleaning and maintenance of the appliance

must not be undertaken by children without

supervision.

Applicable areas of use

The appliance is intended for use an appliance

for the production of domestic hot water: it must

be connected to a heating installation, and while

complying with the instructions, connected to

the drinking water network.

The intended use of the appliance includes the

following points:

•Following the instructions for operating,

installing and maintaining this appliance and

all of its components.

• Ensuring the compliance of the appliance to all

inspection and maintenance conditions which

are listed in this manual.

Danger of death by electrocution

• Touching live electrical wires can cause severe

bodily injury, and lead to death by electrocution.

All installation and maintenance work must be

carried out with the appliance switched o and

by a qualied professional. Before carrying out

any work on the appliance:

-Cut-o the electricity supply.

- Ensure that there is no possibility of the power

supply becoming active again.

-Wait at least 5 minutes for the capacitors to

lose their charge.

• Do not get water on any of the control or

electrical components. Always disconnect the

appliance from the electricity supply before

carrying out work on any of the electrical

components.

Danger of death if the pressure relief valves

are missing or defective

A defective pressure relief valve may prove

dangerous and could lead to burns or other

injuries by, for example, the pipes bursting.

The information presented in this document does

not contain all of the schematic diagrams needed

for a professional installation of the pressure relief

valves.

• Install the necessary pressure relief valves on

the circuit.

• Inform the user concerning the function and

the placement of the pressure relief valves.

• Respect all applicable national and international

regulations, standards and decrees.

Risk of material damage

The heat pump can only work when lled with

water. Never switch on the appliance if it is not

completely lled with water and purged of air.

Rules and regulations (decrees, standards,

laws)

Once the appliance is installed and switched

on, all decrees, directives, technical rules, safety

measures and standards, must be respected in

their current version in eect.

The electrical supply must conform to all

applicable regulations in the country of

installation, as well as the NFC 15-100 standard.

• A methodof disconnection ensuring acomplete

cut-o must be installed in the xed piping to

conform to installation regulations (do not use

a movable outlet).

•Protect the appliance with a 2-pole circuit

breaker with a minimum contact opening of

3mm and must be grounded.

• The devices for electrical cut-o must remain

accessible.

• Water may drain from the discharge pipe of

the pressure limiting device. This pipe should

be kept open to open air.

• The pressure relief valve is mounted on the

condenser. Ensure that the drainage is properly

oriented to prevent water from leaking onto the

electrical components.

Maintenance - Troubleshooting

Maintenance and cleaning of the pilot must be

carried out at least once a year by a qualied

professional.

- MANUAL HTi70 6 & 8 KW HEAT PUMPS -5

This appliance is in compliance with the

international standards concerning electrical

safety CEI 60335-1, CEI 60335-2-102. The

CE branding on the appliance attests to its

compliance with the following directives:

- Low voltage (LV): 2014/35/UE

- Electromagnetic compatibility(CEM):

2014/125/CE

- Ecodesign concerning products related to

energy: 2013-813-UE

• Any intervention on the refrigeration circuit

must be made by a qualified person who

holds a Category 1 certicate of tness.

Refrigerant R290, contained in the heat pump

circuit, does not pose an environmental hazard

but is ammable.

→Refrigerant R290 is odorless.

→Do not damage the refrigeration circuit

tubes,

→Do not handle ame or other ammable

sources inside the device,

→In the event of a leakage of the refrigerant,

unplug the plug, ventilate the room and

contact the customer service,

→Do not pierce or burn the appliance: the

recovery of the uid is mandatory in case

of intervention on the refrigeration circuit.

REFRIGERANT CIRCUIT

Type and refrigerant charge.

PS High: Max high service pressure

PS Low: Max low service pressure

2 -PLEASE READ

IMMEDIATLY

This technical installation manual forms part of the appliance which

it refers to. In order for the warranty to be valid, the instructions must

be read prior to using the appliance.

The safety advice and instructions provided in this manual must be

strictly respected.

Our society is not liable for any damages caused from not following

the instructions provided, or improper handling, installation or use.

This technical installation manual can be modied without prior

notice.

This manual must be safeguarded and passed on to successive users

for future reference.

It will be considered as evidence in case of litigation.

2.1 - Conservation of documents

DHW.......Domestic Hot Water

DCW .......Domestic Cold Water

T°..............Temperature

HP............Heat pump

2.3 - Abbreviations and acronyms

Indicates warnings and important recommendations.

2.2 - Symbols used

Contains regulated substances, do not throw in the

garbage. If disposing, please respect all regulations

pertaining to the recovery of electric and electronic

equipment.

Heat power output produced.

Max current protection (A)

The «Origine France Garantie» certication applies only to HTi70

6 and 8 mono models in combination with some pilot.

2.4 - Certication

«Origine France Garantie»

PRIMO

Pilot

Premium+

Pilot

DS170d

Pilot

HTi70 6 mono Ref. 155001 Ref. 155006 Ref. 155004

HTi70 8 mono Ref. 155011 Ref. 155016 Ref. 155014

Caution : contains a ammable refrigerant uid.

Please make sure to respect the installation and

handling precautions.

Consult the installation manual before any intervention

on the product, before handling, installation, use , and

maintenance.

- MANUAL HTi70 6 & 8 KW HEAT PUMPS -

3.2 - Storage and transport

Admissible storage and transport temperatures of the appliance are

between -20°C and +60°C.

The appliance must be stored in a room that does not contain

sources of ignition that are continuously operating (for example,

bare res, gas appliance or electric radiator in operation).

3.2.1 - General information

The appliances must be stored and transported packaged and

on their wooden pallets, in a vertical position, and completely

empty of water.

3.2.2 - Transporting with a forklift

When transporting with a forklift truck, the Heat Pump must be on

its wooden pallet.

When moving the Heat Pump do not lower or raise the unit suddenly

as the Heat Pump can easily lose it equilibrium. The Heat Pump should

be suitably secured to prevent it from tipping.

3.2.3 - Transporting manually

3.1 - Delivery terms and conditions

In general, the material is transported at the recipient’s own risk.

It is important to verify that all of the elements have been received

and that no damage has been sustained during transport upon

receipt of the appliance and before beginning the installation

procedures.

3 - DELIVERY AND

STORAGE

The Heat pump can be

transported manually.

The Heat pump must always

be transported in a horizontal

position, including during

installation.

Do not handlethe unit by its

hydraulic connections, but by

using the four straps.

Installation procedures must

be carried out by a qualied professional, so as to prevent any risks

of bodily harm and/or material damage.

Do not incline more than 30°

Maintain a protective covering on the nned

heat exchanger during handling.

1. Heat pump

2. Hydraulic pilot

3. Hydraulic connection kit

3.1.1 - HTi70 6 & 8kW

- MANUAL HTi70 6 & 8 KW HEAT PUMPS -7

4 - INTRODUCTION

1. Compressor

2. Pressure reducer

3. Evaporator

4. Condenser

5. Ventilator

6. Heating inlet / outlet

7. Condensates drainage

Note:

The Heat Pump is exclusively designed for heating purposes.

It cannot be used for cooling.

The manufacturer cannot be held responsible for any other usage

of the appliance.

4.1 - Operation

The Heat pump is a closed and pressurised system in which the

refrigerant serves as the medium for transferring energy.

The evaporator dis a cooling exchanger which draws calories from

the air. The humidity in the air condenses on contact with the cold

surface, and forms condensation which must be drained regularly

during operation of the Heat pump (evacuation in h).

The condenser eis a plated heat exchanger which allows to transfer

the heat towards the heating water of the installation g.

The operating range of the Heat pump ranges from an air

temperature of -20°C to 40°C.

It is FORBIDDEN:

•tooperatetheHeatpumpusing airintake

containing solvents or explosive materials.

• to use air intake containing grease, dust, or

aerosol particles.

• to connect vented exhaust hoods to the

appliance.

Use of the appliances are FORBIDDEN if

the installation is not lled with water.

External defrost kit (Réf. 754101)

to keep the external condensate evacuation duct from

freezing.

Adjustable raiser kit for heat pump (Réf. 754600)

allows raise of the heat pump and catch up with ground levels.

4.3 - Accessories available to order

2-core sheathed cable (Ref. 753102)

linking the Heat Pump and the Pilot (lg 20m)

20m length for connection instead of the

10m length delivered as standard.

4.2 - Accessories (included)

The components described below are delivered with the Heat

Pump:

2-core sheathed cable linking the

Heat Pump and the Pilot (lg 10m)

Hydraulic Fitting (Ref. 754206)

(included a 1’’ lter valve, a safety valve assembly 1’’, a hydraulic

connection [reduction F3/4 M1’’ + nipple MM 1’’])

- MANUAL HTi70 6 & 8 KW HEAT PUMPS -

5.1 - Standard conguration

5 - INSTALLATION

•The Heat pump must be installed outside exclusively.

• Avoid any obstruction of the airow of the ventilator.

Ensure that there is nothing blocking the exchanger’s air circulation. Ensure that the Heat pump is placed so that

it is sheltered from dominant winds.

It is prohibited to install the Heat pump:

• In a non-ventilated room.

• Near sources of excessive heat, combustible

materials, or near ventilation points of adjacent

buildings.

• Near a kitchen or workshop exhaust ducts; this

can result in a mixture of oil and air settling onto

the heat exchanger ns which could hamper its

performance.

• In an area with ammable gaz, acidic substances,

or alkalines which could cause irreversible

damage to the copper-aluminium heat

exchanger.

PROHIBITED INSTALLATION

•Avoidinstallingthe Heatpump ina location

subject to noise reverberation such as near

windows or near the corners of buildings.

• As the condensates draining trough slopes

downward, the Heat pump must be installed on a

level base.

• The Heat pump must be easily accessible so as to

facilitate access for inspections and maintenance.

IMPORTANT INSTALLATION RULES

Pilot

HTi70

heat pump

2 electrical supplies

230V single phase

hydraulic

connection

communication

cable

2-core sheathed

- MANUAL HTi70 6 & 8 KW HEAT PUMPS -9

5.2 - Placement

The Heat Pump is designed to be installed outdoors exclusively, while respecting a minimum of free space around the appliance in an area free

from excessive levels of dust. It should never be placed in an enclosed space.

The Heat Pump is designed to operate in rainy weather conditions, although it can be installed under a well-ventilated shelter (Withan opening

large enough to allow sucient air ow for intake and exhaust).

Regarding the fan, the free space from any obstacles must be at least 2m.

≥ 30cm

≥ 1m

≥ 30cm ≥ 30cm

≥ 2m

Placed on the

ground or on a

terrace

(empty area) Placed against a wall

+3dB (A) Placed in a yard

+9dB (A)

Placed in a corner

+6dB (A)

5.2.1 - Noise levels

The Heat Pump is equipped with a large diameter fan so as to allow for an appropriate air ow rate. This ow rate can rise up to 9.000 m3/h. The

fan speed is adjustable to limit the noise level.

Depending on the installation conditions, the noise levels may be dierent, in particular if the walls closest to the Heat Pump cause a reverberation

and amplication of noise.

The diagrams below show dierent installation examples for dierent placements.

5.2.2 - Safe area

The heat pump contains a ammable refrigerant. In case of leak, the refrigerant could accumulate near the ground (higher density than air). or

spread through openings in the building. In order to limit the risk of a toxic, suocating, explosive or dangerous atmosphere, a safety perimeter

must be established around the machine.This perimeter must not include a window, door, or any openings towards the interior of the building.

5.2.2.1 - Ground security area

Observe this area if the heat pump is in free eld.

- MANUAL HTi70 6 & 8 KW HEAT PUMPS -

5.2.2.2 - Security area in front of a wall

This area must be respected if the heat pump is against a wall and close to the opening of a building.

Distances from the security perimeter (mm)

HTi70 6kW HTi70 8kW

A 1000 1000

B 1000 1000

C 1300 1600

D 300 300

5.2.4 - Prohibited installation sites

Underneath a

window

Neighbouring

home

5.2.3 - Accepted installation sites

Oset from all

windows

The noise prevention screen must be made of insulated materials.

Neighbouring

home

Neighbouring

home

Neighbouring

home

Otros manuales para HTi70 6

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Bomba de calor de auer

auer

auer HTi70 6 Manual de usuario

auer

auer HTi70 11 Manual de usuario

auer

auer DS170 d Manual de usuario

auer

auer Edel 100 AIR Manual de usuario

auer

auer PRIMO pilot Documento técnico

auer

auer HRC 70 32 three-phase /3 Manual de usuario

auer

auer HRC 70 PILOT-PREMIUM Manual de usuario

auer

auer HRC 70 PILOT-PREMIUM Manual de usuario

auer

auer HRC70 17 Manual de usuario

auer

auer HRC 70 PILOT-PREMIUM Manual de usuario

auer

auer Premium+ Manual de usuario

auer

auer HRC70 35/2 t Manual de usuario

Manuales populares de Bomba de calor de otras marcas

MICROWELL

MICROWELL HP 1000 GREEN Manual de usuario

Sanyo

Sanyo SAP120FCH Manual de usuario

Daikin

Daikin EHYHBH05AA Manual de usuario

Panasonic

Panasonic WH-SDF03E3E5 Guía

Bryant

Bryant 544B Manual de usuario

Airxcel

Airxcel 45000 Series Manual

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Manual de usuario

Dimplex

Dimplex LI 16I-TUR Guía del usuario

Carrier

Carrier WSHP Open v3 Guía de configuración rápida

TGM

TGM CTV14CN018A Manual de usuario

Carrier

Carrier 38MGQ Series Manual de usuario

Kokido

Kokido K2O K880BX/EU Guía de solución de problemas

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Guía rápida

Carrier

Carrier 48EZN Manual de usuario

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Instrucciones de funcionamiento

Ariston

Ariston NIMBUS Manual de usuario

Weishaupt

Weishaupt WWP L 7 Guía del usuario

GE Zoneline AZ85H09EAC Manual de usuario