Audiovox VOH702 Manual de usuario

92+

32:(5

92/80( &+$11(/

6(/( &7

$87 2

352

6(1 625

79 9 9

+HDGSKRQH +HDGSKRQH9LGHR$XGL R /$XGL R 5

$X[

21 2)) $872

6&5( (1

02'(

-2-

Important Notice

It is unlawful in most jurisdictions for a person to drive a

motor vehicle which is equipped with a television viewer

or screen that is located in the motor vehicle at any point

forward of the back of the driver’s seat, or that is visible,

directly or indirectly, to the driver while operating the

vehicle. In the interest of safety, the VOH702 should

never be installed where it will be visible, directly or

indirectly, by the operator of the motor vehicle.

Please note that the state of Rhode Island forbids the

installation of such a device in a motor vehicle.

Television Reception

This entertainment system is designed primarily for

viewing pre-recorded movies or playing video games.

Television reception in a moving vehicle will be

limited and in some areas will not be possible due to

weak and variable signal strength. Television

viewing in a stationary vehicle will result in an

improvement, but may still be marginal due to

strength. The quality of the picture will not be

consistent with home TV reception. Reception may

be affected by the weather and distance from the TV

station. A weak signal may cause the picture to roll,

be snowy, or cause some color loss.

-3-

Congratulations on your purchase of the Audiovox

VOH702 drop down TV/Video monitor. The VOH702

has been designed to give you and your family many

years of video entertainment in the mobile environment.

Please read the directions that follow to familiarize

yourself with the product and to ensure that you obtain

the best results from your equipment. Please note:

Installation options vary, see the individual owner’s

manuals for each component in your system to obtain

a full understanding of each component’s operation.

Safety Precaution

For safety reasons, when changing video tapes it is

recommended that the vehicle is not in motion, and that

you do not allow children to unfasten seat belts to

change tapes or make adjustments to the system.

System adjustments can be accomplished using the

remote control unit, while seat belts remain fastened.

Enjoy your Audiovox entertainment system but

remember- safety of all passengers remains the

number one priority.

FEATURES

•7” TFT (Thin Film Transistor) Active Matrix LCD

(Liquid Crystal Display) Monitor

•OSD (On Screen Display) for control of Picture

Quality and Functions

•Screen Mode 16:9 or 4:3

•Full Function Remote Control

•Television Tuner

•Plug in RF Transmitter for wireless RF Headphones

•Remote Sensor eye

•Four Audio / Video Sources

•Headphone / Speaker Amplifier

•Two Headphone Jacks for Wired Headphones

•Built-In Dome lights

•Back-lit Controls for Low Light Operation

FRONT PANEL FEATURE

Figure 1

-4-

32:(5

92/80( &+$11(/

6(/(&7

$872

352

6(162 5

79 9 9

+HDGSKRQH +HDGSKRQH9LGHR$XGLR /$XGLR 5

$X[

21 2)) $872

6&5((1

02'(

























FRONT PANEL FEATURES – See Figure 1

1. Power Button- (Bright red when system is ON, dim

when system is OFF)

2. Screen Mode- Used to select screen 16:9 or 4:3.

3. Channel Up/Down- Changes the TV channel

4. Volume Up/Down- Controls volume to headphone

jacks and external speakers if connected.

5. Auto Pro Switch- Auto Program used to program

local channels into TV memory. Press when vehicle

is in a new location.

6. Source Select- Used to select one of the three A/V

sources. The fourth source is plugged into the RCA

jacks on the rear of the unit. V2 must be selected

once something is plugged into the external jacks it

over rides the previous source on V2.

7. Sensor Eye- Allows the remote control to operate the

VOH702’s OSD system (On Screen Display), volume

to wired headphone jacks (and optional external

speakers), and for control of Video Cassette Player

and other accessories.

8. Three Position Dome Light-

•Auto- Will automatically switch on the dome lights in

conjunction with the vehicle’s interior illumination.

For the automatic position, shift the switch to the

right.

•OFF- The dome lights will be off in the middle

position.

•ON- The switch must be in the left position for the

dome lights to turn on.

9. Dome Lights- Provide additional interior illumination

10. Screen Release- Slides in the direction of the arrow

to release the drop down screen.

11. Headphones Jacks- Allows plug-in of two wired

headphones with 1/8” stereo plug.

12. Auxillary A/V Stereo Input- Allows plug-in of

Camcorder, game, portable DVD player or other A/V

source with RCA type output connectors. V2 must be

selected. Plugging into this input over rides the

previous source on V2.

-5-

REMOTE CONTROL OPERATION

-6-

BATTERY INSTALLATION

Before attempting to operate your Remote Control,

install the batteries as described below.

1) Turn the remote control face down. Press down

on the ridged area of the battery cover, and slide

it off.

2) Install two “AAA” batteries as shown. Make sure

that proper polarity (+ or -) is observed.

3) Slide the cover back until it clicks into position.

The remote control will operate the VOH702,

Audiovox Televisions and Video Cassette Players.

It is not a universal remote control and will not

control equipment from other manufacturers.

If a universal remote control is used with the

VOH702, choose the remote control encoding

scheme for Action Televisions when programming

the remote.

-7-

Remote Controlled TV Functions

1. POWER ON/OFF

Press this button to turn the VOH702 on. The

channel number or current video source will be

displayed on screen, and the picture will appear in

a few seconds. Press the button again to turn the

VOH702 off.

2. DIRECT ACCESS (0-9) BUTTONS

Use these buttons to make a direct channel

selection. The channel number chosen will be

displayed on the screen for about 4 seconds. The

direct access is carried out with 0-9 keys (0-99CH).

The “1__” key will not function as it is only used for

cable channels above 99.

3. CHANNEL UP/DOWN BUTTONS

Use these buttons to advance to the next higher or

lower channel. See also: SKIP/SEARCH BUTTON.

4. VOLUME UP/DOWN BUTTONS

Use these buttons to raise or lower the volume

level of the headphone jacks or external speaker if

installed. They are also used to make adjustments

In picture select mode.

Note: These buttons will not affect the volume of

wireless headphones or a wired RF modulator.

When using these devices the volume must be

adjusted with the headphone volume control or with

your radio’s volume control. (See page 11,

Headphones, or page 12, Wired FM Modulator).

5. PICTURE SELECT BUTTON

Each time this button is pressed, the screen picture

adjustment display cycles through “adjustment

bars” for CONTRAST, BRIGHTNESS, COLOR, and

TINT. Once the desired adjustment bar is

displayed, use the VOLUME UP/DOWN buttons to

adjust the setting. The display will automatically

turn off if no adjustments are made within 6

seconds, or if any other button is depressed.

6. MUTE BUTTON

Press this button to shut off the sound at the

headphone stations. The screen will display the

volume adjustment bar for 6 seconds, indicating

that the sound has been turned off. Pressing the

button again restores sound to the previously set

level. The mute feature may also be released by

pressing the VOLUME UP/DOWN buttons.

7. TV / VIDEO BUTTON

Any video equipment connected to the

AUDIO/VIDEO inputs can be used with the TV by

pressing this button. Each time the button is

pressed, the Audio/Video source will change in the

following sequence VIDEO1, VIDEO2, and TV.

-8-

8. AUTO MEMORY BUTTON

When the AUTO MEMORY BUTTON is depressed,

all channels in TV mode are searched and tuned; all

channels with video signals detected are

automatically stored. Please refer to page 2 for

more information on TV reception.

9. SKIP/SEARCH BUTTON

This button selects between SKIP and SEARCH

mode. In “SKIP mode” the TV only stops on

channels that are programmed into memory when

the CHANNEL UP/DOWN buttons are used. When

the SKIP is turned off, the TV will only stop on all

active channels.

10. ERASE/WRITE BUTTON

When tuned to a channel press this button to store

or erase the channel from memory. The stored

channel numbers are displayed in “GREEN” on the

screen, and the non-stored channels are in “RED”.

When skip mode is on, the VOH702 will tune to

only the stored channels when using the CHANNEL

UP/DOWN buttons.

REMOTE CONTROLLED VCP FUNCTIONS

These features can only be used with an Audiovox Video

Cassette Player, if this option was installed with your

video package.

11. POWER BUTTON

This button is used to turn the VCP on and off.

12. “REW” REWIND BUTTON

If this button is pushed while the tape is stopped, the

tape will rewind. If this button is pushed while the

tape is playing, the VCP will go into rewind search

mode. For more information consult the Audiovox

VCP owner’s manual.

13. PLAY BUTTON

Press this button to activate play mode while a tape is

loaded into the VCP. This button may also be used to

disengage search and pause modes. For more

information, consult the VCP owner’s manual.

14. “FFWD” FAST FORWARD BUTTON

If this button is pushed while the tape is stopped, tape

will fast forward. If this button is pressed while the

tape is playing, the VCP will go into fast forward

search mode. For more information on the search

feature of the VCP, consult the VCP owner’s manual.

15. REPLAY BUTTON

Pressing this button will rewind the tape and

immediately begin playback when the tape is fully

rewound.

16. STOP BUTTON

Press this button to stop the tape.

-9-

CHANNEL TUNING SETUP

In order to easily access all available channels, it may

be necessary to perform channel auto-programming

whenever the vehicle’s geographic location has

changed, i.e. city to city, weak signal area.

1. Press the AUTO MEMORY button on the remote

control unit or the AUTO PROGRAM button on the

flip down video unit. You will see the TV cycle

through all it’s channels. The built-in

microprocessor will automatically note each

channel that is actively broadcasting in your area.

2. (A) To tune only strong clear channels with the

CHANNEL UP/DOWN buttons, press the

SKIP/SEARCH button on the Remote Control Unit

until “SKIP MODE ON” is displayed on the bottom

of the screen. The TV will now tune only to strong

active channels when the UP or DOWN buttons

are used on the monitor or the remote control.

(B) To tune to weak or marginal channels with the

CHANNEL UP/DOWN buttons, press the

SKIP/SEARCH button on the Remote Control Unit

until “SKIP MODE OFF” is displayed on the bottom

of the screen. Tune to the desired channel using

the CHANNEL UP/DOWN buttons or go directly to

the channel by using the 0-9 buttons on the Remote

Control.

3. To ERASE a channel, press the ERASE/WRITE

button on the Remote Control Unit until “MANUAL

MEMORY XX ERASE” is displayed on screen. To

STORE a channel, press the button until the

MANUAL MEMORY XX ADD is displayed on

screen.

Note: Please refer to page 2 for more information on

TV reception.

TURNING THE VOH702 ON OR OFF

1. Sliding the screen release lock forward will unlock

the LCD screen and it will drop down slightly.

(Pivot the screen downward until a comfortable

viewing angle is reached). After the unit has been

turned on and displaying a picture, adjustment to

the viewing angle can be made by pivoting the

screen to optimize the picture quality. The internal

friction detent will hold the screen in position while

the system is in use.

2. Pressing the power button on the pod or remote will

alternately turn the system on or off. When in use

the internal back lighting will illuminate the controls.

3. Remember to turn the unit off and pivot the LCD to

the locked position when not in use.

-10-

OPERATION

Overhead Dome Lights

The lights integrated into the VOH702 are controlled by

a three position slide switch. Sliding the switch to the

on position will turn the lights on. The off position will

prevent the lights from turning on at all times, and the

auto position will allow the lights to turn on and off with

the vehicle’s interior lighting. Do not leave the vehicle

unattended with the dome light switch in the on position,

as this could result in a discharged battery.

The switch is shown in the center position. See page 5

for more details.

Light Switch

Screen Release

Remote Sensor

The VOH702 incorporates an infrared sensor, which

relays the signals from the remote control to allow the

VOH702 and VCP to be controlled simply by pointing

it’s remote control at the remote sensor. This provides

control of auxiliary equipment such as an Audiovox

Video Cassette Player. The infrared sensor can relay

signals from any manufacturer’s remote control to it’s

respective component connected to the Video 1 and 2

inputs, such as a DVD player. In this case you must

use the remote control supplied with the DVD player.



32:(5

92/80( &+$11(/

6(/(&7

$872

352

6(1625

79 9 9

6&5((1

02'(

Remote Sensor

Tabla de contenidos

Otros manuales de Sistema de vídeo para coche de Audiovox

Audiovox

Audiovox HR9000D Manual de usuario

Audiovox

Audiovox Mobile Video VOD100 Manual de usuario

Audiovox

Audiovox Mobile Video 128-8810 Manual de usuario

Audiovox

Audiovox DVD1627 Guía de planificación

Audiovox

Audiovox MMDV70CB Manual de usuario

Audiovox

Audiovox 50-0245x-002 SERIES Manual de usuario

Audiovox

Audiovox VOD10PS2 - Car - 16:9 Flipdown Monitor Manual de usuario

Audiovox

Audiovox AVXMTG13UA Manual de usuario

Audiovox

Audiovox AVXMTG10UA Manual de usuario

Audiovox

Audiovox HR7008APKG Manual de usuario

Audiovox

Audiovox VOH-642 Manual de usuario

Audiovox

Audiovox VOD710 - DVD Player With LCD Monitor Manual de usuario

Audiovox

Audiovox VOH701 - VOH 701 - LCD Monitor Manual de usuario

Audiovox

Audiovox VOD 808 Manual de usuario

Audiovox

Audiovox HR9000PKG Manual de usuario

Audiovox

Audiovox Mobile Video VOD128A Manual de usuario

Audiovox

Audiovox VOD80 Guía de inicio rápido

Audiovox

Audiovox VOD850 - Car - Overhead LCD Monitor Manual de usuario

Audiovox

Audiovox PROV 710 P Manual de usuario

Audiovox

Audiovox 50-0246x-015 Series Manual de usuario

Audiovox

Audiovox LCM 7070 Manual de usuario

Audiovox

Audiovox 1187001PL Manual de usuario

Audiovox

Audiovox PROV716 Manual de usuario

Audiovox

Audiovox Rampage VBP1000S Manual de usuario

Manuales populares de Sistema de vídeo para coche de otras marcas

Stinger

Stinger HEIGH10 RB10RAM13B Manual de usuario

Eonon

Eonon E1057 Manual de usuario

Milion

Milion D2223 Manual de usuario

Metra Electronics

Metra Electronics 99-8153 Manual de usuario

Voxx Electronics

Voxx Electronics HR8MA1 Manual de usuario

Axxera

Axxera AV604Bi Manual de usuario

Clarion

Clarion NX706E Manual de usuario

Pyle view

Pyle view PLDN74BTi Manual de usuario

Clarion

Clarion NX602 Manual de usuario

PowerAcoustik

PowerAcoustik PTID-5850N Manual de usuario

RCA

RCA DRC6296 - Twin 9" Mobile DVD System Guía del usuario

Lanzar

Lanzar SVDVD5 Manual de usuario

Kia

Kia MTXM100YPPE Manual de usuario

Eonon

Eonon E1060 Manual de usuario

Macrom

Macrom M-AN900 Manual de usuario

Hyundai

Hyundai BAPE-L3000N Manual de usuario

r.LiNK

r.LiNK RL2-UCON8-SM Manual de usuario

Blaupunkt

Blaupunkt DVP 01C Manual de usuario