Audiovox PS-155CH Manual de usuario

128-6460

1 of 8

3 Button Remote Security System with

Stage Shock Sensor & Starter Disable

Model APS-155CH

Owner’sManual

FEATURES :

w2 Three Button Code Hopping RF Transmitters

wThree Channel Code Learning Receiver (capable of accepting 4 transmitters)

wSelectable Manual Override Mode

wRemote Panic in all modes

wProtected Valet

w7 Function LED -(Light Emitting Diode) - Arm / Disarm / Zone1, 2, 3 / Valet / Arming

wIntrusion Alert with Memory

wAudible Arm / Disarm / Defective Zone / Tamper Confirmation

wInstant Siren Activation

wLow Current Horn Output

wStarter Disable ( Optional relay required )

wTrue Last Door Arming ( hardwire only )

wDefective Zone By - Pass

wHardwire or Voltage Sense Selectable

wActive or Passive Arming Selectable

wProgrammable Auto Lock On / Off

wProgrammable Auto Unlock On / Off

wProgrammable Door Lock Pulse Duration 1 Second / 3.5 Seconds/1 Sec L/ Dbl. U/L

wProgrammable Active or Passive Door Locks

wUserProgrammablePermanentChirpDelete

wOn Command RF Chirp Delete from Transmitter (Software Selectable)

w6 Tone Multi - Tone Siren

wAdditional Negative Trigger Input

wRF Inhibit with ignition on

wParking Light Flasher

wPlug In Dual Stage Shock Sensor

OPTIONS :

wRemote Trunk Release

wRemote Keyless Entry

wMultiple Vehicle Capable

wRemote Starter

wRemote Power Window Roll Up

wRemote Garage Door Interface

128-6460

2 of 8

NOTE: Your system has the option of using a siren, the vehicle horn, or both for the

sounding device. Where the siren is referenced below, the horn or both may in fact

chirp, or beep.

ARMING THE SYSTEM - ACTIVE

1. Turn off the engine, exit the vehicle, and close all doors, hood lid, and trunk lid.

2. Press and release the ARM button on the keychain transmitter.

þThe dash mounted LED begins to flash slowly.

þParking Lights flash one time.

þSiren and or Horn sounds one chirp.

If the siren/horn sounds 3 chirps, then you have left a door, trunk, or hood lid

ajar. Simply close the opened entry point to provide full protection. If the siren

"chirped" three times, sometime after arming, the exclusive delayed dome

light learn circuit has been programmed and the system detected a open

entry point after the learned delay expired. Again, closing the hood, trunk, or

doors will correct the problem and you do not need to disarm the system to

make the correction. If the siren/horn did not sound when arming, then the

chirps have been turned off, and you should refer to the section titled “

ELIMINATINGTHEARM/DISARM CHIRPS“inthismanual.

oDoors Lock - Optional

SILENT ARMING - ACTIVE

1. Turn off the engine, exit the vehicle, and close all doors, hood lid, and trunk lid.

2. Press and hold the ARM button on the keychain transmitter for 2 seconds.

þThe dash mounted LED begins to flash slowly.

þParking Lights flash one time.

þSiren/Horn will not sound.

If the siren/horn sounds 3 chirps, then you have left a door, trunk, or hood lid

ajar. Simply close the opened entry point to provide full protection.

oDoors Lock - Optional

NOTE: Chirps must be selected on to access this feature

ARMING THE SYSTEM - PASSIVE ( AUTOMATIC )

1. Turn off the engine, exit the vehicle, and close and lock all doors, hood lid, and trunk lid.

þThe dash mounted LED begins to flash rapidly, indicating 30 second passive

arming has begun.

2. Opening any protected entry point during the 30 second passive arming cycle will

immediately suspend automatic arming, and the 30 second passive arming cycle will re

start when all doors are closed. At the end of the passive arming cycle;

þThe dash mounted LED begins to flash slowly.

þParking Lights flash one time.

þSiren and or Horn sounds one chirp

If the siren did not sound when arming, then the chirps have been turned off,

and you should refer to the section titled “ ELIMINATING THE ARM / DISARM

CHIRPS“in this manual.

oDoors Lock - Optional

Door locking during passive arming is a selectable feature. The alarm can be

programmed to allow the doors to lock only when arming using the keychain

transmitter, and they will not automatically lock during passive arming.

Page 2

128-6460

3 of 8

Page 3

PROTECTION WHILE THE SYSTEM IS ARMED

þOpening any protected door, hood, or trunk lid will cause the alarm to immediately

sound. The alarm will continue to sound for 30 seconds, then stop and continue to

monitor all protected entry points. If the thief left a door opened, the alarm will sound

for six 30 second cycles, remain armed and ignore that triggered zone.

þWhenever the system is armed, the dash mounted LED indicator will slowly flash.

This serves as a visual deterrent to the potential thief. The LED is a very low current

bulb, and will not cause the vehicle’s battery to drain, even when left unattended for

extended periods.

þWhenever the system is triggered, the vehicle’s parking lights will flash for the full 30

second alarm cycle, attracting visual attention to the vehicle.

oWhenever the system is armed, the vehicle’s starting circuit will be bypassed. If the

thief should choose to ignore the siren/horn, the vehicle can not be started.

þAny strong impact to the vehicle’s glass will cause the alarm to trigger for the full 30

second alarm cycle.

oAny mild impact to the vehicle's glass will cause the alarm to sound a short series of

warning tones.

DISARMING THE SYSTEM

1. As you approach the vehicle, press and release the DISARM button on the keychain

transmitter.

þThe dash mounted LED turns off.

If passive arming was selected during the installation, then the LED will start

flashing rapidly, indicating that the system is re arming automatically. Open

any door to suspend the automatic arming.

þParking Lights flash two times.

If the parking lights flashed three times, then the alarm was triggered in your

absence. Before turning the key on, examine the LED to identify which zone

was triggered.

þSiren / Horn sounds two chirps.

If the siren/horn sounds 4 chirps, then the alarm was triggered in your

absence. Before turning the key on, examine the LED and refer to the INTRU-

SION WARNING SIGNALS section of this manual to identify which zone was

triggered.

If the siren/horn did not sound when disarming, then the chirps have been

turned off, and you should refer to the section titled “ ELIMINATING THE ARM

/DISARMCHIRPS “ in thismanual.

oDoors Unlock - Optional

SILENT DISARMING

1. As you approach the vehicle, press and hold the ARM / DISARM button on the keychain

transmitter for 2 seconds.

þThe dash mounted LED turns off.

If passive arming was selected during the installation, then the LED will start

flashing rapidly, indicating that the system is re arming automatically. Open

any door to suspend the automatic arming.

þParking Lights flash two times.

128-6460

4 of 8

Page 4

If the parking lights flashed three times, then the alarm was triggered in your

absence. Before turning the key on, examine the LED to identify which zone

was triggered.

þSiren/Horn does not sound.

If the siren and or horn sounds 4 chirps, then the alarm was triggered in your

absence. Before turning the key on, examine the LED and refer to the

INTRUSION WARNING SIGNALS section of this manual to identify which

zone was triggered.

oDoors Unlock - Optional

NOTE: Chirps must be selected on to access this feature

WHILETHESYSTEM IS SOUNDING

If during a triggered state, you wish to shut off the siren without disarming your security

system, simply press and release any transmitter button other than the disarm button. This

action will turn off the siren yet leave the vehicle fully armed and protected. This feature is

particularly useful if you are aware of children playing near your vehicle that may acci-

dently trigger your security system. In this case you can cancel the siren sounding

INTRUSIONWARNING SIGNALS

This system will inform you if an intrusion attempt has occurred while you were away from

the vehicle. If an intrusion attempt has occurred, the siren/horn will chirp 4 times and the

parking lights will flash 3 times when disarming the system. Enter the vehicle, and observe

the dash mounted LED to identify which zone was triggered.

If the LED is flashing one time...pause...one time...pause...etc., then an

intrusion attempt was made to the shock sensor, or an accessory triggering

device that may have been added to the system.

If the LED is flashing two times...pause...two times...pause...etc., then an

intrusion attempt was made to a hood or trunk pin switch that was added to the

system, or to a light activated entry point if the alarm was installed using the

voltage sensing feature.

If the LED is flashing three times...pause...three times...pause...etc., then an

intrusion attempt was made through one of the vehicle’s doors.

These intrusion warning indicators are stored in the system’s memory, and will only be

erased when the ignition key is turned on.

VALET SWITCH

The valet switch allows you to temporarily bypass all alarm functions, eliminating the need

to hand your transmitter to parking attendants or garage mechanics. When the system is in

valet mode, all alarm functions are bypassed, however the remote panic feature and

remote door locks will remain operational. To use the valet mode, the system must first be

disarmed either by using your keychain transmitter, or by operating the manual override

sequence.

1. From the disarmed condition, turn the ignition key to the on position.

2. Press and hold the valet push-button switch until the dash mounted LED,

(Light Emitting Diode) turns on. The LED will remain on as long as the system

is in valet mode.

3. To return to normal operation, press and release the push button switch any

time the ignition is on.

128-6460

5 of 8

Page 5

NOTE: Always remember to return the system to the NON VALET mode, after servicing, to

ensure that the vehicle remains protected at all times.

MANUALLYOVERRIDINGYOURSYSTEM:

USING THE VALET SWITCH MANUAL OVERRIDE

Your Security System can be disarmed without the use of the keychain transmitter. This is

necessary, since you will need the ability to operate your vehicle if the transmitter is lost or

its battery fails. If your system has been selected for Valet Switch manual override as

indicated on the last page of this manual, to by-pass the alarm system.

1. Open the vehicle door. The alarm will sound.

2. Turn the ignition key to the on position.

3. Within 5 seconds, press and release the valet push button switch.

The alarm system will stop sounding and enter the disarmed mode. You can now start and

operate the vehicle normally.

Typically this override mode is used only if the transmitter has become inoperative. You

may elect to enter the VALET mode until repair or replacement of the transmitter, after

which, returning the system to the full operation mode is necessary. To do so, see item 3

under the heading VALET SWITCH.

Programming Your Custom Override Code:

Unlike override switches easily found, and defeated, this security system allows the

consumer to program a personal override code, offering a higher level of security. To take

advantage of this option, programmable feature # 10 must be selected for the Custom Code

Option. Consult your installation center for programming details. The system comes from

the factory with a pre-programmed override code of 11. To change this default override

code, do the following:

1. Disarm the system by use of the transmitter, or by use of the emergency override

sequence. Turn the ignition switch to the on position.

2. Within 10 seconds, press and release the valet/override switch, 3 times.

3. Within 10 seconds turn the ignition switch off, on, off, on, off, on. (The siren or horn

will beep and the lights will flash one time. LED turns On)

4. Within 10 seconds, begin to enter your chosen 10ths digit by pressing and releasing

the push-button switch from 1up to 9 times.

5. Within 10 seconds of the last entered 10ths digit, turn the ignition switch off then on.

6. Within 10 seconds, begin to enter your chosen units digit by pressing and releasing

the push-button switch from 1 up to 9 times.

7. Finish by turning the ignition switch to the off position.

If the new code was accepted, the unit will report back the newly entered code, by

flashing the LED, first indicating the 10ths digit, pause and then the units digit. The unit will

report the new code three times with a one second pause between each code, then the

system will begin arming. If the LED flash pattern

reports the previously stored code, the new code was not entered correctly. Please

repeat steps 1 through 7 above considering the following.

NOTE: Acceptable digits 10ths or units are 1 through 9. The unit will not recognize a

0 (Zero), or no digit entered in any place, units or tenths.

NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for more than

128-6460

6 of 8

5 seconds during any of the above steps, the unit will revert back to the last

successfully stored code.

Custom Code Programming Example:

To Change the code from the factory pre-assigned code of 11 to “52” you would do the

following:

1 Disarm the system by use of the transmitter, or by use of the emergency override

sequence.

2 Turn the ignition switch to the on position.

3 Within 10 seconds, press and release the valet/override switch, 3 times.

4 Within 10 seconds turn the ignition switch off, on, off, on, off, on. (The siren or horn

will beep and the lights will flash one time. LED turns On)

5 Within 10 seconds, begin to press and release the push button switch to set the tenths

digit. (As per the example, press and release 5 times to set the tenths digit to 5)

6 Within 10 seconds of the last press of the push-button, turn the ignition switch off then

on.

7Within 10 seconds, begin to press and release the push button switch to set the units

digit. (As per the example, press and release 2 times to set the units digit to 2).

8Turn the ignition switch to the off position. Immediately observe the LED flash pattern.

You will note the LED flashing five times, pause, and then flash two times, pause. This

pattern will be repeated three times indicating the new code (52) has been accepted and

stored in memory.

NOTE: If after step 8, the LED flashes a code other than what was just entered, this

indicates that the code has not been changed. You will have to repeat steps 1

through 7 above being certain to note the following:

Acceptable digits 10ths or units are 1 through 9. The unit will not recognize

a 0 (Zero), or no digit entered in any place, units or tenths.

NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for more then

5 seconds during any of the above steps, the unit will revert back to the last

successfully stored code.

MANUALLY OVERRIDING YOUR SYSTEM:

USINGTHE CUSTOM CODEOVERRIDE

Assuming the override code programmed has not been changed, and the default override

code of 11 is in the system's memory.

1) Enter the vehicle and turn the ignition switch to the on position.

Note: The siren will sound.

2) Within 5 seconds, press and release the push-button switch 1 time.

3) Within 5 seconds, turn the ignition switch off then on.

4) Within 5 seconds, press and release the push-button switch 1 time.

5) Turn the ignition switch off then on and start the vehicle.

Note: If you have changed the programmed override code then substitute your new code

tenths for step 2 above, and units for step 5 above.

ELIMINATING THE NORMAL ARM / DISARM CHIRPS

As explained earlier in the manual, you can eliminate the chirps selectively any time you arm

or disarm the system, if so programmed, simply by holding the ARM / DISARM button for two

seconds. If you find the normal arming and disarming chirps annoying, they can be turned

Page 6

128-6460

7 of 8

off permanently, eliminating the need to hold the ARM / DISARM button for two seconds. To

do this,

1. Turn the ignition key on then off.

2. Within 10 seconds, press and release the valet push button switch three times.

3. If the chirps were on before you started, then you will hear 2 chirps indicating they

have been turned off.

If the chirps were off before you started, then you will hear one chirp indicating they have

been turned on.

NOTE: Whenever the chirps are by - passed, the 4 chirp intrusion indicator and 3 chirp

defective zone indicator will always operate. Since these are important warnings to

you that something has happened, they cannot be eliminated.

REMOTEPANICOPERATION

The ARM or DISARM button on your keychain transmitter also functions as a panic switch

for use in emergency situations. To use remote panic,

1. Press and hold the ARM or DISARM button on the keychain transmitter for 3 or

more seconds. The alarm will immediately sound.

2. To stop the alarm, press and hold the ARM or DISARM button on the transmitter again

for 3 seconds. If the button is not pressed, the alarm will automatically stop after 30

seconds. Also if any transmitter button other than the ARM or DISARM button is

pressed and released, the Panic mode will be turned off immediately. The normal

function of this transmitter button will be suspended during the Panic sounding period.

3. During the panic mode, the Lock and Unlock buttons can be used to lock and unlock the

doors, (if the option is installed), however once the unlock/disarm button is pressed,

the vehicle's starter inhibit device, (where installed) will be disabled allowing the

vehicle to start.

NOTE: While in the Panic mode, pressing and releasing the ARM or DISARM buttons will, if

the option is installed, lock and unlock the doors respectively. While in the panic

mode, anytime the DISARM button is pressed, the panic feature will continue for the

allotted 30 seconds, however, the security system will be disarmed allowing the

vehicle to start.

ADDITIONAL REMOTE FUNCTION ( CHANNEL 3 )

This security system has an additional features that can be connected to a number of

different optional accessories. Some of the more common uses for this channel are;

oRemote Trunk Release

oRemote Car Starter

oRemote Window Closure

oRemote Garage Door Interface

Operation of the optional accessory or accessories, can be controlled by pressing and

holding the programmed button on the keychain transmitter for four seconds, or by pressing

and releasing the programmed button on the transmitter two times in succession. Check

with your installation center for more information on what accessories were installed and

how they are accessed.

Page 7

128-6460

8 of 8

©AudiovoxElectronicCorp. 150Marcus Blvd.,Hauppauge, N.Y. 11788 128-6460

APS-155CH

SYSTEMFUNCTIONSAT AGLANCE

DASHLED INDICATORS

RAPIDFLASHING = PASSIVEARMING

SLOWFLASHING = ARMED

OFF = DISARMED

ONSOLID = VALETMODE

3FLASH...PAUSE = INTRUSIONZONE3

2FLASH...PAUSE = INTRUSIONZONE2

1FLASH...PAUSE = INTRUSIONZONE1

SIRENCHIRP INDICATORS

1CHIRP* = ARM

2CHIRPS* = DISARM

3CHIRPS = ARM/DOOROPENED

4CHIRPS = DISARM/INTRUSION

* These chirps are optional, and can be de - activated.

PARKING LAMPS

1 FLASH = ARM

2FLASHES = DISARM

3FLASHES = DISARM/INTRUSION

Your System Has These Features Activated

oRemote Keyless Entry

oAuto Lock with ignition key

oAuto Unlock with ignition key

oPassive Arming

oNo Lock in passive mode

oHardwire doors, hood, and trunk

oRF Chirp Delete On

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Alarma de coche de Audiovox

Audiovox

Audiovox Prestige APS-25CH Manual de usuario

Audiovox

Audiovox APS 750a Manual de usuario

Audiovox

Audiovox Platinum APS 500 Manual de usuario

Audiovox

Audiovox Pursuit PRO-9344FT Manual de usuario

Audiovox

Audiovox PRO-9344FT Pursuit Series Manual de usuario

Audiovox

Audiovox Pursuit PRO 9445FT Manual de usuario

Audiovox

Audiovox Prestige Platinum APS 600 Manual de usuario

Audiovox

Audiovox Auto Security XR91 Instrucciones de funcionamiento

Audiovox

Audiovox Prestige Platinum APS-400 Manual de usuario

Audiovox

Audiovox Exclusive EX-6000 Manual de usuario

Audiovox

Audiovox UTX-ETX Instrucciones de funcionamiento

Audiovox

Audiovox Prestige Platinum APS-410a Manual de usuario

Audiovox

Audiovox Auto Security AS-9950 Manual de usuario

Audiovox

Audiovox Platinum Prestige APS-750 Manual de usuario

Audiovox

Audiovox Prestige Platinum APS-995C Manual de usuario

Audiovox

Audiovox Prestige Platinum APS-300R Manual de usuario

Audiovox

Audiovox AA-9005 Guía de solución de problemas

Audiovox

Audiovox Prestige Platinum 128-8533 Manual de usuario

Audiovox

Audiovox Pursuit PRO9801 Manual de usuario

Audiovox

Audiovox PRO 9549FT3 Manual de usuario

Audiovox

Audiovox Pursuit PRO 9842B Manual de usuario

Audiovox

Audiovox Pursuit PRO-9775T Manual de usuario

Audiovox

Audiovox Prestige 128-8601 Manual de usuario

Audiovox

Audiovox Pursuit PRO-9671FT Manual de usuario

Manuales populares de Alarma de coche de otras marcas

Clifford

Clifford 3606X Manual de usuario

Ultra Start

Ultra Start 2500M SERIES Manual de usuario

Ultra Start

Ultra Start 650 Series Manual de usuario

Sparkrite

Sparkrite SRA8 Manual de usuario

Viper

Viper 4708V Manual de usuario

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Manual

Falcon

Falcon Predator XL3 Guía del usuario

Clifford

Clifford Sabre II Manual de usuario

CrimeStopper

CrimeStopper CS-8717 Guía de inicio rápido

Ultra Start

Ultra Start 450 SERIES Manual de usuario

Scytek electronic

Scytek electronic Vectra X3 Manual de usuario

Excalibur

Excalibur AL-1860-EDPB Manual de usuario

Clifford

Clifford CYBER 2 Manual de usuario

Gemini

Gemini 7057 Manual de usuario

FlashLogic

FlashLogic FLRSBA PRESTIGE Manual de usuario

Magicar

Magicar FAI-440 Manual de usuario

Clifford

Clifford Nova 3 Manual de usuario

Viper

Viper 560XV Manual de usuario