Audiomatica CLIO FW-02 Manual de usuario

3 CLIO INSTALLATION

3.1 MINIMUM PC CONFIGURATION

The CLIO FW-02 USB interface running the CLIO 12 software can be installe in any

personal computer with the following minimum system requirements:

– Processor: single-core @ 2GHz clock or ual-core (suggeste )

– One free USB 2.0 port

– 1024x786 vi eo a apter

– Microsoft Win ows XP, Vista, 7, 8 or 10

BE SURE TO HAVE ADMINISTRATIVE RIGHTS WHEN INSTALLING!

3.2 FW-02 DRIVERS INSTALLATION

To install the FW-02 rivers in your computer you shoul follow the instructions

presente below:

1) Connect the FW-02 to a free USB 2.0 port on your PC an power it with its 12V

supply. You shoul hear the classical soun of plug an play evices.

NOTE: ClioXP is the nickname of the FW-02 evice seen by Win ows.

2) After the initial automatic river etection only one evice shoul be foun am

properly installe by Win ows, the USB Composite Device; two more evices,

name ClioXP will nee to be installe manually. Open Device Manager (type

devmgmt.msc from Run prompt or click Control Panel>System>Device

Manager); you shoul fin this situation:

3 CLIO INSTALLATION 1

3) Insert the CLIO 12 installation CD-ROM in the PC.

4) Right-Click on each ClioXP evice un er Other Devices an choose Up ate Driver

Software. At the successive prompt:

5) Browse your computer an point to the fol er insi e the installation CD where

the proper rivers are locate (for example \Driver\10).

2 3 CLIO INSTALLATION

Ignore any Microsoft's warning message about Digital Signature or Publisher an

reach the en of the wizar .

6) Inspecting again the Device manager confirms you the proper ClioXP Control an

ClioXP Stream entries un er USB controllers category:

3 CLIO INSTALLATION 3

You d ive installation was successful!

3.3 FW-02 DRIVERS INSTALLATION UNDER WINDOWS XP

1) Connect the FW-02 to a free USB 2.0 port on your PC an power it with its 12V

supply. You shoul hear the classical soun of plug an play evices.

NOTE: ClioXP is the nickname of the FW-02 evice seen by Win ows.

2) The Foun New Har ware Wizar etects the CLIO XP evice:

As the CLIOXP rivers are unknown to Win ows you will be prompte with this

search win ow:

4 3 CLIO INSTALLATION

3) Insert the CLIO 12 installation CD-ROM in the PC.

Search in the proper CD fol er (for example Drivers\XP)

5) Do not stop to Microsoft Warning about Win ows Logo testing.

3 CLIO INSTALLATION 5

6) Open Device Manager (type devmgmt.msc from Run prompt or click Control

Panel>System>Device Manager); you shoul fin this situation:

You d ive installation was successful!

3.5 SOFTWARE INSTALLATION

This paragraph eals with softwa e installation.

Be su e to have administ ative ights when installing CLIO.

The CLIO software is provi e either on its own CD-ROM, SD car or, in electronic

6 3 CLIO INSTALLATION

format, as a single, self-extracting, executable file.

To install the CLIO 12 software in your computer you shoul follow the instructions

presente below:

1) Insert the CLIO 12 CD ROM in the computer.

3) Choose CLIO 12 installer to start installation.

The proce ure is completely automatic an will only request you to accept the

Software En User's License Agreement an input some information in or er to

correctly install CLIO 12; the software installer will also check your operating

system version.

After successfully completing this proce ure take note of the installation irectory

of CLIO (usually C:\Program Files\Au iomatica\CLIO12 or C:\Program Files

(x86)\Au iomatica\CLIO12 ).

3 CLIO INSTALLATION 7

3.6 RUNNING CLIO FOR THE FIRST TIME

If you have complete the prece ing installation proce ure, you are rea y to run

CLIO!

3.6.1 THE 'CLIO BOX' AND CLIO SERIAL NUMBER

A few wor s about the FW-02 USB interface.

This unit is nee e to correctly interface analog signals to your PC; it is also

important as it has an internal reference use to calibrate the system an also

stores the system's serial number insi e its internal EEPROM; Figure below shows

where is locate your CLIO system serial number.

The CLIO se ial numbe is ve y impo tant and should be mentioned each

time you get in contact with Au iomatica, either for technical support or for

software upgra e.

Also the CLIO system accessories have their serial numbers; keep track of those

but mention to technical support ONLY UPON REQUEST.

When using your CLIO system you will normally use the FW-02 front connectors. As

you'll become extremely familiar with this har ware unit we are going to give it a

nickname: from now on we will call it 'the CLIO Box'. Also the CLIO software

refers to it with this nickname.

8 3 CLIO INSTALLATION

3.6.2 THE FIRST RUN

The following steps will guide you th ough a complete ve ification of the

system pe fo mance and ope ation.

From the Sta t Menu choose P og ams, then CLIO 12 an click on the CLIO icon.

The program shoul start smoothly an present the main esktop.

If the system is not calibrate , as the first time you run it, you will receive the

following message.

Shoul CLIO isplay an error message take note of it an go to the troubleshooting

section.

3.6.3 INITIAL TEST MEASUREMENT

Let's now execute our first test measurement - play an capture a 1kHz sinusoi .

First of all click on the In-Out Loop button for channel A; in this way the CLIO

Box connects output A with input A with an internal relay. This connection is very

important as it lets you capture an analyze a signal generate by CLIO without the

nee for an external connecting cable.

Then click on the generator icon to play the 1kHz sinusoi (1031.25Hz to be

exact; more on this later, it's the efault signal). Then press the F4 keystroke to

invoke the Multi-Meter as in Figure.

3 CLIO INSTALLATION 9

If everything is OK you shoul obtain a rea ing of circa 1V, variable between a

minimum of 0.95V an a maximum of 1.05V, which is the mean output level of a

sinusoi al signal when the system is not calibrate .

Now press the FFT button (or CTRL-F), then press the Oscilloscope button an

finally the GoButton.

The result you shoul obtain is an FFT analysis of the 1kHz sinusoi (one spectral

line @ 1kHz at 0 BV) an its time representation given by its oscillogram.

Both Multimeter an FFT results must present stable an repeatable; the

oscillogram shoul isplay a sinusoi without spikes or rops of any kin .

IMPORTANT NOTE: Only if these two initial tests gave correct results, as

escribe , go to the following paragraph an execute the system calibration; if you

are not able to obtain these results an they seem in any way corrupte do not

execute calib ation an contact technical support.

10 3 CLIO INSTALLATION

Tabla de contenidos

Manuales populares de Equipo de grabación de otras marcas

KV2 Audio

KV2 Audio 500 Series Manual de usuario

Robotics Technologies

Robotics Technologies microBus-Cam II Manual de usuario

Seca

Seca 460 Manual de usuario

Cognex

Cognex MVS-8000 Series Manual de usuario

Mect

Mect MPNC006 Series Manual de usuario

Bad Caf

Bad Caf THE LEASH Manual de usuario

Strymon

Strymon NIGHTSKY Manual de usuario

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manual de usuario

Tews Technologies

Tews Technologies TPMC465 Manual de usuario

Honeywell

Honeywell Excel 50 Manual de usuario

SeaLevel

SeaLevel COMM+8.LPCI Manual de usuario

Arturia

Arturia AUDIOFUSE STUDIO Manual de usuario

Rukra

Rukra RK-1240 Manual de usuario

Samson

Samson SCOM Manual de usuario

Dynacord

Dynacord DPS260 Manual de usuario

Nice

Nice Core Manual de usuario

Pyle Pro

Pyle Pro PSS8 Manual de usuario

RF-System

RF-System TinyGate Manual de uso y cuidado