Audio Technica AT-LP120BK-USB Manual de usuario

Tabla de contenidos

Otros manuales de Placa giratoria de Audio Technica

Audio Technica

Audio Technica AT-LP120XBTa-USB Manual de usuario

Audio Technica

Audio Technica AT-PL120 Instrucciones de funcionamiento

Audio Technica

Audio Technica VM740ML Manual de usuario

Audio Technica

Audio Technica AT-PL120 Manual del propietario

Audio Technica

Audio Technica AT-LP60-BT Manual de usuario

Audio Technica

Audio Technica AT-LPW50BT Manual de usuario

Audio Technica

Audio Technica AT-LPW50PB Manual de usuario

Audio Technica

Audio Technica AT-PL50 Instrucciones de funcionamiento

Audio Technica

Audio Technica AT-LP60XBT-USB Manual de usuario

Audio Technica

Audio Technica AT-LP120XUSB Manual de usuario

Audio Technica

Audio Technica AT-LP3XBT Manual de usuario

Audio Technica

Audio Technica AT-LP5X Manual de usuario

Audio Technica

Audio Technica AT-LP60XUSB Manual de usuario

Audio Technica

Audio Technica VM750SH Manual de usuario

Audio Technica

Audio Technica AT-LP60X-RD Manual de usuario

Audio Technica

Audio Technica AT-LP3BK Manual de usuario

Audio Technica

Audio Technica VM520EB/H Manual de usuario

Audio Technica

Audio Technica AT-LP120XBT-USB Manual de usuario

Audio Technica

Audio Technica AT-LP120-USB Manual del propietario

Audio Technica

Audio Technica AT-LP5 Manual del propietario

Audio Technica

Audio Technica AT-LP5 Manual del propietario

Audio Technica

Audio Technica AT-LP5 Manual del propietario

Audio Technica

Audio Technica VM540ML Manual de usuario

Audio Technica

Audio Technica AT-LP120-USB Manual de usuario

Manuales populares de Placa giratoria de otras marcas

Gemini

Gemini CDT-05 MKII Manual de usuario

Rotel

Rotel RP-820 Manual de usuario

Shuman

Shuman MC-250BT Manual de usuario

Stanton

Stanton STR8-150 Manual de usuario

Crosley

Crosley McQueen CR7011-GY Manual de usuario

Reloop

Reloop SMP-1 Manual de usuario

auna

auna TT-Classic Plus Manual de usuario

COMO AUDIO

COMO AUDIO Turntable Analog Manual de usuario

Dual

Dual 1009 F Manual de usuario

REED

REED Muse3C Manual de usuario

AXIOMTEK

AXIOMTEK OPS883-H Series Manual de usuario

Pioneer

Pioneer PL-71 Manual de usuario

Vestax

Vestax PDX-a1 Manual de usuario

Denon

Denon DP-400 Manual de usuario

Dual

Dual 504 Manual de usuario

Audio-Techica

Audio-Techica AT-LP60XBT Manual de usuario

Goldring

Goldring G99 Manual de usuario

Acoustic Signature

Acoustic Signature Typhoon NEO Manual de usuario

Setting Up the AT-LP120-USB Turntable –

Part 1

01.13.2015Audio-Technica 84 Comments

The AT-LP120-USB Turntable is a professional direct-drive turntable with both analog and USB

connection capability, so you can use it with all standard audio equipment or plug it directly into

your computer. But make no mistake, this isn’t just a tool to transfer records to MP3s – it’s

loaded with all the tools you’d expect from a professional turntable, including adjustable tone

arm and pitch control, ½-inch Dual Magnet™ cartridge, three speeds (33/45/78), DJ

functionality and more.

But, as with most professional gear, proper setup is critical to getting the most out of the AT-

LP120-USB and ensuring long-lasting operation of the stylus and enjoyment of your records. In

this post we’ll cover headshell and counterweight installation, and tone arm balance. In Part 2

we’ll tell you have how to set the tracking force and pre-amp selector switch, and make anti-

skate and tone arm height adjustments.

The first order of business is to put all the pieces in place. So set the platter and slip mat onto the

turntable spindle, making sure the platter is fully seated. Next, lock the tone arm in place in the

tone arm rest and attach the headshell assembly by inserting it into the end of the tone arm.

While continuing to hold the headshell, rotate the locking ring on the tone arm counterclockwise

to pull the headshell securely into place.

Now install the counterweight. With the black stylus force gauge facing forward, screw the

counterweight onto the back of the tone arm. Then, if you intend to use the dust cover, slip its

hinges into the slots on the back of the turntable and slide the cover into place on the hinges.

Once you have all that taken care of, you can move on to the important matter of balancing the

tone arm. This will help ensure that the cartridge tracks properly and that the stylus won’t wear

prematurely or damage your records. To get started set the anti-skate dial to 0.

Remove the protective cover from the stylus by sliding it straight forward off the front of the

cartridge. Take hold of the headshell and then release the tone arm’s locking clamp. The tone

arm will be unbalanced at this point, so take care not to damage the stylus by letting it come into

contact with the slip mat (or anything else). While continuing to gently hold the headshell, rotate

the counterweight until the tone arm is horizontally balanced –it should hover just above the

platter. Once this is done, lock the tone arm back in place on its rest.

Setting Up the AT-LP120-USB Turntable –

Part 2

01.15.2015Audio-Technica 37 Comments

In Part 1, we told you how to install the headshell and counterweight, and how to balance the

tone arm. Now it’s time to set the stylus tracking force. Setting the force properly will keep the

stylus from skipping out of the record groove at especially dynamic musical passages (too little

force) and prevent excessive wear to stylus and records (too much force).

The recommended force varies from cartridge to cartridge, so first you need to determine which

cartridge you’re dealing with. The AT-LP120-USB currently comes with an AT95E cartridge

(identifiable by its green stylus). Prior to September 2011, the turntable was equipped with the

now discontinued ATP-2XN (white stylus). If you are working with the AT95E, we recommend

setting the force to 2 grams; if you have the ATP-2XN, set the force to 3.5 grams. (If you ever

install an alternate cartridge, you’ll need to adjust the tracking force according to the

manufacturer’s recommended setting.)

As you’ll recall from the previous post, the stylus force gauge is located on the front of the

counterweight. Without adjusting the counterweight, rotate the force gauge so the number 0 lines

up with the centerline marked on the rear of the tone arm. Then set the tracking force by rotating

the entire counterweight (the force gauge should turn along with the weight) counterclockwise

until reaching the desired value.

Also, to compensate for the natural “skating” force that pulls the tone arm toward the center of

the record, set the anti-skate knob to match the value of the tracking force. However, if you

anticipate doing a fair amount of back-cueing, scratching or reverse-direction operation, you may

want to use less or no anti-skate control.

If you use a taller cartridge, thicker slip mat or play thick records (such as 180 g pressings or old

78s), you may also need to adjust the tone arm height in order to keep the tone arm parallel. To

do so, loosen the height-lock switch and rotate the black height-adjust dial –the lock and dial are

both located at the base of the tone arm. Once the height is adjusted correctly, secure it by

flipping the switch back into locked position.

Finally, adjust the PHONO/LINE selector switch on the back of the turntable to set the proper

output. If the turntable is connected to a receiver or other device with a dedicated phono input,

move the switch to PHONO. If the turntable is connected to a sound card, powered speakers or

AUX-type inputs, set the selector to LINE, which will activate the turntable’s internal pre-amp.

If you are using the USB output to connect the turntable to a computer, the selector switch can be

set to either PHONO or LINE as the switch doesn’t affect USB output in any way.