Atronix AX2.88kWhBM Manual de usuario
HIGH VOLTAGE BATTERY
Installation
and Operation Manual
AX2.88kWhBM
AX2.88kWhBS
Machine Translated by Google
INTRODUCTION
It contains important regulations and information for the use of this product and provides technical
support for the operator of the device.
The publication and copyright of this documentation remain with the company: AKKU SYS
Akkumulator- und Batterietechnik Nord GmbH Gleitnweg 23
D-25469 Halstenbek Telephone +49 4101
37676-0 • Fax +49 4101 85475-66 • www.akkusys.de • akkusys. shop
Read carefully
before use!
All rights reserved.
Read this instruction manual carefully before installation.
Page 3
3
4
4
4
6
7
7
8
9
9
11
11
12
13
14
16
18 19 21
Our EU declaration of conformity and warranty conditions can be found at: www.a-tronix.de
AKKU SYS Akkumulator- und Batterietechnik Nord GmbH cannot be held responsible for any
inaccuracies or inappropriate information in these operating instructions. The information in this
document is subject to change without notice, but there is no obligation to continually update it.
We reserve the right to make design and device changes that serve to improve the production
process or the product.
Page 2
User manual a-
TroniX AX2.88kWhBM + AX2.88kWhBS
5.1 Specifications BM + BS 5.2
Battery system a-TroniX 2.88kWh BM / BS
Table of Contents 1. Introduction 2.
Symbols 3.
Safety 3.1
Handling 3.2
Installation 4.
Responding to
Emergency Situations 5. Product
Information
22
7.1 Contents of the
package 7.2
Clearance 7.3
Tools 7.4 Installation steps
7.5 Wiring steps 7.6 System
startup 8. Commissioning
9. Exclusion 10.
Troubleshooting
and maintenance 10.1
Maintenance
10.2 Troubleshooting
6. Product features
6.1 Battery system features 7.
Installation
22
23
Machine Translated by Google
Be careful, risk of electric shock.
The battery chemistry of these products is lithium iron phosphate. This manual
Read the instruction manual before starting installation and operation.
a-TroniX AX2.88kWhBS
Install the product out of the reach of children.
Disconnect the device from the power supply before carrying out any
maintenance or repair work.
User manual explain.
is intended for qualified personnel only. The tasks described in this document should
only be performed by authorized and qualified technicians. After installation, the
installer must provide the end user with the
Do not dispose of the product with household waste.
This mark indicates that the requirements for product safety certification are
composite in the UK.
Observe the precautionary measures for handling devices at risk
of electrostatic discharge.
Caution, risk of electric shock, energy storage with time-limited
discharge.
SymbolsSymbol Explanation CE mark. The inverter complies with
the requirements of the applicable CE guidelines.
Protective conductor connection
a-TroniX AX2.88kWhBM
Do not place near flammable or explosive materials.
The document describes the installation, commissioning, maintenance and
troubleshooting of the high-voltage batteries listed below.
Page 3
2. Symbols
1. Introduction
Machine Translated by Google
• Store the device out of the reach of children and animals.
• Do not expose the product to direct sunlight.
• Always handle the battery with insulated gloves.
• Do not connect the storage device to the conductors of the inverter or the
photovoltaic system. This will cause damage to the battery and may result in an
explosion.
• Do not mix up the positive and negative poles of the battery.
• Do not expose the batteries to open flames.
• Do not touch any liquid that comes out of the device. There is a risk of electric
shock or skin injuries.
• Make sure the inverter and battery are completely turned off before beginning
installation.
In the event of an accident, a fire or explosion may occur.
This can lead to damage.
• Store the device in a cool and dry place with sufficient ventilation.
• Do not place the device near combustible materials.
• Do not step on the device or place foreign objects on it.
• Store the product on a flat surface.
• Do not charge or discharge damaged batteries.
• Do not store the device near water sources.
• Do not store batteries near water sources.
• Do not damage the device by dropping it, deforming it, hitting it, cutting it or
penetrating it with a sharp object. This may result in electrolyte leakage or fire.
• After unpacking, check the product for damage and missing parts.
Any work on the batteries should be carried out by authorized technicians. It goes
without saying that technicians should familiarize themselves with the contents of
this manual before carrying out any maintenance or installation work on the system.
3.2 Installation
3.1 Handling
page 4
3. Security
Machine Translated by Google
• Do not connect the battery to an incompatible inverter.
• In the event of fire, only use dry powder fire extinguishers. Liquid fire extinguishers
must not be used.
• Installing the battery outdoors is strictly prohibited.
• Do not use the battery in high static environments where the protection device
could be damaged.
• Do not open the battery to repair or disassemble it. Such repairs may only be
carried out by a-TroniX.
• Do not exceed the permissible battery voltage of the inverter.
• Make sure all batteries are properly grounded.
• Do not install the battery near children or pets.
where the battery can get wet.
• Make sure there is no short circuit between terminals or with an external device.
• Do not connect different battery types together.
• Do not install together with other batteries or cells.
• Do not install the battery near water sources or in places
page 5
Machine Translated by Google
• If it comes into contact with skin, wash the affected area thoroughly with soap and
• If inhaled, please leave the contaminated area immediately and search
In any fire situation, please evacuate people from the building immediately before
attempting to extinguish the fire.
see a doctor immediately.
See a doctor.
• If swallowed, induce vomiting and seek medical attention.
• In case of eye contact, rinse eyes with running water for 15 minutes
The battery modules are not waterproof. Therefore, be careful not to get them wet. If the
battery is fully or partially submerged in water, do not attempt to open it. For further
instructions, contact authorized personnel or a-TroniX.
The battery storage consists of several batteries connected in series. They are designed
to avoid danger or failure. However, a-TroniX cannot guarantee its absolute security.
and see a doctor immediately.
In case of contact with the internal materials of the battery, the user should follow the
following recommendations.
In situations where the battery is on fire, if it is safe to do so, turn off the battery by turning
off the circuit breaker to remove power to the system. Use an FM-200 or CO2 fire
extinguisher for the battery and an ABC fire extinguisher for the other parts of the system.
water location
Fire situation
page 6
4. Responding to emergency situations
Machine Translated by Google
BM
Specifications for AX2.88kWh B.S
5. Product information
Page 7
2.5
(CC-CV) Standard charging current (A)
-20~55
5~95
65
570*380*155
Discharge peak current (60s) (A)
57.6
37.7
50
Normal voltage (V)
Weight (kg)
Max. charge/discharge current (A)
2.88
-10~55
48.6~65.7
Normal energy (kWh)
CAN
50/50
Storage temperature (°C)
25
Max. Continuous Discharge/Charge Current (A)
-10~55
2.5
-20~55
65
Constant current and voltage charge shutdown current (A)
5~95
570*380*170
57.6
31.8
Dimensions (L*W*H) (mm)
50
50
2.88
Normal capacity (Ah)
Communication interfaces
48.6~65.7
Operating temperature (°C)
50/50
Battery voltage range (V)
CAN
50
25
Humidity (%)
5.1 Specifications BM / BS
Machine Translated by Google
Normal voltage (V)
Discharge current (A)
35@-20±2°C @1C;50@25±2°C @0.5C;47@55±2°C @0.5C
230.1
65
* T) [mm]
8.64
Protection class
172.8
Shutdown current (A)
134.7
The number of batteries
20.16
Charge: 0 ~55, discharge: -10 ~55
Normal capacity (Ah)
403.2
50/50
11.52
(CC-CV) Standard
charging current (A)
ÿ6000 @25°C @ 70%SOH
Communication
interfaces
230.4
Discharge peak current
(60s) (A)
Storage temperature (°C)
H
Dimensions
Battery voltage range
(V)
Temperature range (°C)
166.5
1BM+1BS
50
25
(B*
Constant current and
Cycle life
CAN
Normal energy (kWh)
71.1
Characteristics
14.4
-20~55
288
IP65
1BM+2BS 1BM+3BS 1BM+4BS 1BM+5BS 1BM+6BS
Max. charging/
Discharge capacity (Ah)
198.3
voltage charge
5.76
2.5
Weight (kg)
115.2
Battery
name*
17.28
Operation
Ingress protection
345.6
Class I
102.9
page 8
IFpP42/151/ 108/[(18S)3S]
108/[(18S)2S]
E/-10+50/90
570*380*350 570*380*470 570*380*590 570*380*710 570*380*830 570*380*950
IFpP42/151/
E/-10+50/90
User manual a-
TroniX AX2.88kWhBM + AX2.88kWhBS
IFpP42/151/IFpP42/151/
E/-10+50/90
IFpP42/151/
E/-10+50/90 E/-10+50/90
108/[(18S)6S]
E/-10+50/90
108/[(18S)4S] 108/[(18S)7S]108/[(18S)5S]
IFpP42/151/
5.2. Battery system a-TroniX 2.88kWhBM + BS
97.2~131.4 145.8~197.1 194.4~262.8 243~328.5 291.6~394.2 340.2~459.9
Specifications for AX2.88kWhBM + BS
Machine Translated by Google
Page 9
6.1 Battery system features
Operating instructions
a-TroniX inverter AX series
BS features:
BM features:
Mounting hole for
bracket
Handle
Right
ground terminal
• Inverter interface protection: over-voltage, over-current, external short-circuit, reverse
polarity, ground fault, over-temperature, over-current
• Interface:
• Battery protection: Internal short circuit, over voltage, over current, over temperature,
under voltage
The batteries are equipped with multiple protection systems to ensure the safe operation
of the system. Some of the protection systems include:
• Interface:
The battery system has the following interfaces so that it can be connected and operated
efficiently.
6. Product features
Machine Translated by Google
Page 10
BMS status LED and SOC LED
DC OUTPUT -
Operating status LED
Bat + connection of the inverter.
at.
POWER switch
Switch to turn on the system, press this switch to start the system.
Connection Bat - of the inverter.
This LED is used to indicate whether the battery is working effectively. A green light on this LED means the
battery is on and functioning normally. If the battery is not functioning properly, a red glow on this LED means
the battery is not functioning properly.
DC switch
After switching on, press this button for 5 seconds.
B start switch
DC OUTPUT +
The LEDs show specific alarm information and the performance of the battery system
Power switch, battery charge and discharge switch.
Machine Translated by Google
Otros manuales para AX2.88kWhBM
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Paquete de baterías de Atronix
Manuales populares de Paquete de baterías de otras marcas
IOGear
IOGear GBP24V Series Manual de usuario
Inventus Power
Inventus Power PROTRXion S-12V100-TRX-HD Manual de usuario
Clas Ohlson
Clas Ohlson PW-290A Manual de usuario
EINHELL
EINHELL MULTI-Ah Power X-Change Plus Manual de usuario
Samsung
Samsung EB-U3300 Manual de usuario
ECTIVE
ECTIVE LC Series Manual de usuario