Atos BullSequana Edge Manual de usuario
-1
Customer Service
Guide
BullSequana Edge
86 A1 93FR 03 - March 2020
The following copyright notice protects this book under Copyright laws which prohibit such actions
as, but not limited to, copying, distributing, modifying, and making derivative works.
Copyright ©Bull SAS 2020
Printed in France
Trademarks and Acknowledgements
We acknowledge the right of proprietors of trademarks mentioned in this manual.
All brand names and software and hardware product names are subject to trademark and/or
patent protection.
Quoting of brand and product names is for information purposes only and does not represent
trademark and/or patent misuse.
Bull Cedoc
357 avenue Patton
BP 20845
49008 Angers Cedex 01
FRANCE
March 2020
Hardware
The information in this document is subject to change without notice. Bull will not be liable for errors contained
herein, or for incidental or consequential damages in connection with the use of this material.
Contents i
Table of Contents
Preface p‐1...............................................................................
Intended Readers p‐1.................................................................
Chapter 1. Servicing a network antenna 1-1.......................................
1.1. Removing a network antenna 1-2..........................................
1.2. Installing a network antenna 1-4...........................................
Chapter 2. Servicing a fan 2-1.......................................................
2.1. Removing a fan 2-2........................................................
2.2. Installing a fan 2-8........................................................
Chapter 3. Servicing the processor air duct 3-1....................................
3.1. Removing the processor air duct 3-2.......................................
3.2. Installing the processor air duct 3-6........................................
Chapter 4. Servicing a memory module 4-1........................................
4.1. Removing a memory module 4-2...........................................
4.2. Installing a memory module 4-7...........................................
Chapter 5. Servicing an accelerator 5-1............................................
5.1. Removing an accelerator 5-2..............................................
5.2. Installing an accelerator 5-7...............................................
Chapter 6. Servicing a 2.5" disk 6-1.................................................
6.1. Removing a 2.5" disk 6-2..................................................
6.2. Installing a 2.5" disk 6-7...................................................
Chapter 7. Servicing a 3.5” disk 7-1.................................................
7.1. Removing a 3.5" disk 7-2..................................................
7.2. Installing a 3.5" disk 7-7...................................................
Chapter 8. Servicing an intrusion detection switch 8-1............................
8.1. Removing an intrusion detection switch 8-2................................
8.2. Installing an intrusion detection switch 8-8.................................
Appendix A. Servicing the top aesthetic cover A-1...................................
A.1. Removing the top aesthetic cover A-1......................................
A.2. Installing the top aesthetic cover A-3......................................
p‐1
Preface
Preface
This guide explains how to replace the Customer Replaceable Units (CRU).
See The Bull support web site for the most uptodate product information,
documentation, firmware updates, software fixes and service offers:
http://support.bull.com
Important ATTENTION: Please read carefully the safety instructions
before you perform the procedures described in this
manual.
ATTENTION : Merci de lire attentivement les consignes de
sécurité avant d'effectuer les procédures décrites dans ce
manuel.
ACHTUNG : Bitte lesen Sie sorgfältig die angegebenen
Sicherheitshinweise, bevor Sie die Verfahren in diesem
Handbuch beschrieben durchführen.
Multilingual Safety Notices Guide, 86 X1 12FL
Intended Readers
This guide is intended for use by administrators and operators.
Chapter 1. Servicing a network antenna 1-1
Chapter 1. Servicing a network antenna
Important ATTENTION: Please read carefully the safety instructions
before you perform the procedures described in this
manual.
ATTENTION : Merci de lire attentivement les consignes de
sécurité avant d'effectuer les procédures décrites dans ce
manuel.
ACHTUNG : Bitte lesen Sie sorgfältig die angegebenen
Sicherheitshinweise, bevor Sie die Verfahren in diesem
Handbuch beschrieben durchführen.
Multilingual Safety Notices Guide, 86 X1 12FL
C004 CAUTION
C004:
Static electricity can damage the server and other electronic devices. To
avoid damage, keep static-sensitive devices in their static-protective
packages until you are ready to install them.
To reduce the possibility of damage from electrostatic discharge,
observe the following precautions:
Limit your movement. Movement can cause static electricity to build up
around you.
Wear an electrostatic-discharge wrist strap.
Handle the device carefully, holding it by its edges or its frame.
Do not touch solder joints, pins, or exposed circuitry.
Do not leave the device where others can handle and damage it.
While the device is still in its static-protective package, touch it to an
unpainted metal surface on the outside of the server for at least 2
seconds. This drains static electricity from the package and from your
body.
Remove the device from its package and install it directly into the
server without setting down the device. If it is necessary to set down
the device, put it back into its static-protective package. Do not place
the device on the server cover or on a metal surface.
Take additional care when you handle devices during cold weather.
Heating reduces indoor humidity and increases static electricity.
See BullSequana Edge Description Guide, 86 A1 65FR to locate the
antenna.
1-2 Customer Service Guide
1.1. Removing a network antenna
Required Tools
None
Procedure
1. Unpack the new component on a clean ESD-protected work surface
2. Power off the server
3. Disconnect the power supply cable
Rear view
4. Remove the aesthetic top cover if the aesthetic covers are present
See Appendix A Servicing the top aesthetic cover
Chapter 1. Servicing a network antenna 1-3
5. Remove the external antenna
Rear view
Otros manuales para BullSequana Edge
2
Tabla de contenidos
Otros manuales de Servidor de Atos
