ATOMSTACK M4 Manual de usuario
ATO M S TA C K M 4 L a s e r M a r k i n g M a c h i n e
F03-0078-0AA1 Version: A
Note: The picture is for reference only, the actual product shall prevail.
For more information, please scan the QR code.
English
Deutsche
Français
Before using the laser marking machine, please read this safety guide carefully, it mentions situations that require special
attention and includes warnings of unsafe practices that can cause damage to your property or even endanger your personal
safety.
1. The product belongs to Class 4 laser products, the laser system itself must meet the requirements of IEC 60825-1 latest version,
otherwise the product is prohibited to be used.
2. When handling the product,you must wear appropriate goggles(OD5+) to protect eyes from laser light including reflected and stray
light.
3.Because cutting burns off the substrate, a high-intensity laser beam generates extremely high temperatures and a lot of heat. Certain
materials can catch fire during cutting, creating gases and fumes inside the equipment. A small flame usually appears here when a laser
beam hits the material. It will move with the laser and will not stay lit when the laser passes by. Do not leave the machine unattended
during the marking process. After use, be sure to clean up the debris, debris and flammable materials in the marking machine. Always
keep an available fire extinguisher nearby to ensure safety. When laser marking machines are used, smoke, vapour, particles, and
potentially highly toxic materials (plastics and other combustible materials) are produced from the material. These fumes or air pollutants
can be hazardous to health.
4.To prevent accidental disasters such as fire and electric shock, the marking machine provides a power adapter with a ground wire.
When using the marking machine, insert the power plug into a power socket with a ground wire with a ground wire .
5.When the marking machine is working, please make sure that the workplace must be cleaned up, and there should be no flammable
and explosive materials around the equipment.
Part 1: Security Statement Before Installation
Part 2: Disclaimer and warning
Thisproductisnotatoyandisnotsuitableforpeopleunder15.
This product is a laser device. Please scan the QR code on the cover to get the complete "User Manual" and the latest instructions and
warnings. All information in this material has been carefully reviewed, if there are any typographical errors or misunderstandings in the
content, please contact us. Technical improvements (if any) of the product will be added to the new Manual without further notice. The
appearance and color of the product are subject to change.
Pleasebesuretoreadthisdocumentcarefullybeforeusingtheproducttounderstandyourlegalrights,responsibilitiesandsafetyinstructio
ns;Otherwise,itmaybringpropertyloss,safetyaccidentandhiddendangerofpersonalsafety.Onceyouusethisproduct,youshallbedee
medtohaveunderstood,andacceptedalltermsandcontentsofthisdocument.Userundertakestoberesponsibleforhisorheractionsa
ndallconsequencesarisingtherefrom.UseragreestousetheProductonlyforlegitimatepurposesandagreestotheentiretermsandcont
entsofthisdocumentandanyrelevantpoliciesorguidelinesthatAtomStackmayestablish.
You understand and agree that Atomstack may not be able to provide you with damage or accident damage unless you provide the
original marking files, configuration parameters of the marking software used, operating system information, videos of the marking process,
and operating steps prior to the occurrence of the problem or failure. reasons and to provide you with Atomstack's after sales service.
Atomstackisnotliableforanyandalllossesarisingfromtheuser'sfailuretousetheproductinaccordancewiththismanual,Without the
guidance of the company's technical personnel, users are prohibited from disassembling the machine by themselves. If this behavior occurs,
the loss caused by the user shall be borne by the user.
Atomstackhastheultimaterighttointerpretthedocument,subjecttolegalcompliance.Atomstackreservestherighttoupdate,modify,or
terminatetheTermswithoutpriornotice.
Part 3:Product Parameters
Detailed Parameters of Machine M4
Laser power
2W
Ambient temperature
0°C~35°C
Repetition accuracy
< 0.001 mm
Marking depth
0.015-0.2mm
Marking accuracy
< 0.001mm
Marking speed
<12m/s
Cooling method
Build-in fan
Wave length
1064nm
Marking range
70*70mm
Marking width
0.001-0.05mm
Product weight
6.77kg
Product dimensions
315mm* 200mm* 273mm (L*W*H)
Part 4: Configuration list
USB Cable Power CordUSB Drive
Ruler Positioning Plate Goggles
Hexagon Wrench Focus filmCalibration paper
Manual
Power Adapter
Plasticine
Part 5:Product structure introduction
Laser Components
Handle
Marking cover
Field
mirror
Repeated
work key
Fan exhaust
port
Focus Assist
Pedestal
Base cover
Height knob
.USB interface
.Power input interface
On/Off
button
Screw cover
.Locking screw
Part 6：Introduction to the assembly method of
the desktop working mode
step 1:Prepare the support arm
and align the mounting holes on
the base
step 2:Install 4 screws step 3:Install the Laser
Assembly
step 4:Install the laser
assembly locking screw
step 5:Tighten the screws of the
laser assembly
step 6:Assembly is complete
step 1:Install the marking cover step 2:Installing the Focus Assist
Protective Cover
Part 7：Introduction to the assembly method of
the hand-held working mode
In the copied file,
find the BslCAD
software and follow
the prompts to
complete the
installation
After the software
installation is
complete, open
SeaCAD in the
software and start
using
Choose a
drawing
tool
Turn on the
power of the unit
and adjust the
focus
Insert the U disk
and connect
the required
computer with
the cable
Open the U disk, find the
driver
CyPressDriverlnstaller file,
copy it to the computer,
double-click to install,
and follow the prompts to
complete the installation;
Part 8：Common operating procedures of the software
draw：Lines,
curves, rectangles,
circles and
polygons
Text: Click on the
auxiliary
toolbar 。
Image: Click on
the auxiliary
toolbar 。
Vector: Click on
the auxiliary
toolbar 。
Click on the
auxiliary
toolbar 、
Edit dimensions,
etc. in the object
properties
window
Click to fill ，
Choose a fill
method“Filling”，
click
Set "Speed (mm/s)"
and "Power (%)" in
"Marker Control
Window"
Click on the
auxiliary
toolbar 、
Edit text content,
fonts, etc. in the
object properties
window and save
Click on the auxiliary
toolbar 、Import the
object to be marked, edit
the parameters such as
inversion, grayscale, DPI in
the property window and
save it
Click on the
auxiliary
toolbar 、
Click to fill ，
Adjust "Line" to
0.04MM, click
Click ，Check
the marking position and
range, if it is not suitable,
please re-adjust and edit
Click ，
start marking
Complete the marking, if
unqualified, please re-
adjust the parameters
In "Mark Configs",
select to enter
"Expand..." interface,
check "Bitmap scan
increment"
Tabla de contenidos
Idiomas:
Otros manuales de Equipos industriales de ATOMSTACK
ATOMSTACK
ATOMSTACK MAKER FB2 Plus Manual de usuario
ATOMSTACK
ATOMSTACK MAKER E85 Manual de usuario
ATOMSTACK
ATOMSTACK MAKER R1 Manual de usuario
ATOMSTACK
ATOMSTACK R3 Rotary Roller Manual de usuario
ATOMSTACK
ATOMSTACK X40 Pro Manual de usuario
ATOMSTACK
ATOMSTACK R2 V2 Manual de usuario
ATOMSTACK
ATOMSTACK R2 Manual de usuario
