Products with CE Marking comply with EMC Directive
(2014/30/EU); Low Voltage Directive (2014/35/EU); RED
(2014/53/EU); ROHS Directive (2011/65/EU) issued by the
Commission of the European Community. Compliance
with these directives implies conformity to the following
European Norms:
EMC: EN 301 489
LVD: EN 60950
Radio: EN 300 328
If the camera system no longer functions or can no longer be repaired, it must be disposed of according to the valid statutory regulations.
Disposal of spent batteries/accumulators:
You are required by law (Battery Ordinance) to return all spent batteries and accumulators. Disposing of spent batteries/accumulators with
common household waste is prohibited! Batteries/accumulators that contain hazardous substances are marked with the symbols on the
side. These symbols indicate that it is prohibited to dispose of these batteries/accumulators in the household waste. The abbreviations for the
respective heavy metals are: Cd=cadmium, Hg=mercury, Pb=lead. You can return spent batteries and accumulators that can no longer be
charged to the designated collection points in your community, outlets or wherever batteries or accumulators are sold. Following these
instructions will allow you to fulll the legal requirements and contribute to the protection of our environment!
Push Notication
a. Enable/disable the push notication:
For Andriod
1. Go to more section to tap Push Notication.
2. Click/unclick to enable/disable the push notication.
3. Enter user name.
4. Tap ”OK” when you done.
For iOS
1. Tap icon.
2. Enable/disable the push notication.
3. Enter user name.
4. Tap ”Save” when you done.
12
3
4
1
2
3
4
For Andriod
1. Tap push notication setting
2. Setup interval time of the push
For iOS
1. Tap push setting
2. Setup interval time of the push
c. Time period:
This function allows you to setup "Do Not Disturb" time. You can setup when Push is to start
and end. Only during the time, you will receive the push.
d. List:
From list section, you can see which smart devices currently receive push from the system.
WDVR app allows max 8 devices to receive the push. You may remove all devices from the
push list by resetting the language.
FACTORY DEFAULT SETTING
1. Go to the system setting.
2. Reset the language.
3. The system will restore to factory default.
Note: Please change default security code and apply push service from smart devices after you reset the
language and system parameter to default.
b. interval
Go to the push notication setting to setup interval time of the push. There are four options
you can select how long you’ll receive the push.
Note: Your smart phone will receive the push immediately after rst triggered. After that the camera will
send the push according to interval time you setup. This function allows you to receive less push of one
serial event happened continuously in time.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation
