Atlas Copco SmartHEAD Manual de usuario

smartHEAD Installation Guide

1 (4) 9836 4569 01 Revision 4

smartHEAD INSTALLATION GUIDE

Index:

INSTALLING THE smartHEAD on the STwrench.................................................................................2

INSTALLING THE smartHEAD on the MRTT-C...................................................................................3

GENERAL

The smartHEAD, to be installed on the STwrench and MRTT-C,

defines the wrench capacity. You can install or change the smartHEAD

without the need of any further settings or calibration: the STwrench

and STanalyser loads automatically the transducer data at the power

on.

PACKAGE

Refer to the check list included for the package list.

SAFETY

Warning: Read the STwrench Product Instruction (No. 9836 4489 00) and MRTT-C User Guide (No.

9836 5984 01) before installing and using the product.

HANDLING

The module is electrostatic sensitive device; DO NOT touch any electrical contact to avoid risk of

module damages.

If possible, before handling any STwrench modules, touch with your hand a big metallic object,

in order to avoid electrostatic discharges while handling the modules.

Observe the following precautions to handle the module:

Correct handling: NOT correct handling:

smartHEAD Installation Guide

2 (4) 9836 4569 01 Revision 4

INSTALLING THE smartHEAD on the STwrench

1. SWITCH OFF THE STwrench.

2. INSERT THE smartHEAD IN THE WRENCH CONTROLLER AND TIGHTEN THE LOCKING NUT UNTIL

WHEN THE “CLICK” IS HEARD

NOTE: there is only one way to insert the smartHEAD into the wrench controller. The guide and

the reference pin must be inserted in the relative housings; do not force them in other position.

3. TURN ON THE STwrench

4. IF THE FOLLOWING MESSAGE IS SHOWN, CHECK THE DATE AND SELECT YES TO CONTINUE

AND USE THE smartHEAD (the first use date is set at the date shown):

Guide

Reference PIN

Locking nut

smartHEAD

smartHEAD Capacity Indication

STwrench

smartHEAD Installation Guide

3 (4) 9836 4569 01 Revision 4

Selecting No the first date is not set, but the smartHEAD is blocked. The messsage above is

shown again at the next STwrench power on.

5. IF THE smartHEAD IS NOT PROPERLY INSTALLED THE FOLLOWING MESSAGE IS SHOWN:

NOTE: each smartHEAD is intended to be associated to a single STwrench controller!

The smartHEAD interchangeability assures easy and fast maintenance operations and wrench

upgrade. IMPORTANT NOTE:

Assembling different heads on the same controller during the normal wrench operations is an

improper use of the modularity concept, and will invalidate the warranty on the wrench

components.

The smartHEAD should be left always connected to the controller. For example, do not

disassemble it at the end of the day of for wrench transportation.

INSTALLING THE smartHEAD on the MRTT-C

6. DISCONNECT THE MRTT-C FROM THE STanalyser / STa 6000.

Locking nut

smartHEA

MRTT

Date

smartHEAD Installation Guide

4 (4) 9836 4569 01 Revision 4

7. INSERT THE smartHEAD IN THE MRTT-C AND TIGHTEN THE LOCKING NUT UNTIL WHEN THE

“CLICK” IS HEARD

NOTE: there is only one way to insert the smartHEAD into the MRTT-C. The guide and the

reference pin must be inserted in the relative housings; do not force them in other position.

8. CONNECT THE MRTT-C TO THE STanalyser / STa 6000 AND TURN ON THE STanalyser / STa 6000

9. IF THE FOLLOWING MESSAGE IS SHOWN ON STa 6000, CHECK THE DATE AND SELECT YES TO

CONTINUE AND USE THE smartHEAD (the first use date is set at the STa 6000 date):

Selecting No the first date is not set, but the smartHEAD is blocked. The messsage above is

shown again at the next STa 6000 power on.

10. IF THE smartHEAD IS NOT PROPERLY INSTALLED THE Transducer Error MESSAGE IS SHOWN.

NOTE: each smartHEAD is intended to be associated to a single MRTT-C!

The smartHEAD interchangeability assures easy and fast maintenance operations and system

upgrade. IMPORTANT NOTE:

Assembling different heads on the same MRTT-C during the normal operations is an improper

use of the modularity concept, and will invalidate the warranty on the wrench components.

The smartHEAD should be left always connected to the MRTT-C. For example, do not

disassemble it at the end of the day of for transportation.

Guide

Reference PIN

Date / time

Tabla de contenidos

Otros manuales de Herramientas eléctricas de Atlas Copco

Atlas Copco

Atlas Copco LTV39-2 R37-B10 Hoja de instrucciones

Atlas Copco

Atlas Copco ETC STR21-28-12-LI5 Manual del propietario

Atlas Copco

Atlas Copco W2630 Instrucciones originales

Atlas Copco

Atlas Copco EP6PTI32 HR10-MT Instrucciones originales

Atlas Copco

Atlas Copco P2505 Hoja de instrucciones

$Atlas Copco TEX140PS Manual de usuario$

Atlas Copco

Atlas Copco TEX140PS Manual de usuario

Atlas Copco

Atlas Copco LTP61 H700-25 Hoja de instrucciones

Atlas Copco

Atlas Copco W2621 Hoja de instrucciones

Atlas Copco

Atlas Copco Cobra mk1 Especificaciones

Atlas Copco

Atlas Copco LTV39-2 R56-HAD Hoja de instrucciones

Atlas Copco

Atlas Copco ETVST101-450-20F Hoja de instrucciones

Atlas Copco

Atlas Copco ETV S7 Manual de usuario

Atlas Copco

Atlas Copco ETD STR61-50-13-T25 Hoja de instrucciones

Atlas Copco

Atlas Copco LH 11 Guía de mantenimiento y servicio

Atlas Copco

Atlas Copco ETP ST32-10-10 Instrucciones originales

Atlas Copco

Atlas Copco PowerMACS 4000 Manual de usuario

Atlas Copco

Atlas Copco ETV ST81-120-HAD Instrucciones originales

Atlas Copco

Atlas Copco ITB-A61-50-10 Manual de usuario

$Atlas Copco TEX 09PS Guía de mantenimiento y servicio$

Atlas Copco

Atlas Copco TEX 09PS Guía de mantenimiento y servicio

Atlas Copco

Atlas Copco LSV28 S040-01M14 LF Instrucciones originales

Atlas Copco

Atlas Copco ETV STB63-70-13-IRC-W Hoja de instrucciones

$Atlas Copco TEX150PE Guía de mantenimiento y servicio$

Atlas Copco

Atlas Copco TEX150PE Guía de mantenimiento y servicio

Atlas Copco

Atlas Copco ITB-A31-05-I06 Instrucciones originales

Atlas Copco

Atlas Copco ETP ST101-1000-25-F Instrucciones originales

Manuales populares de Herramientas eléctricas de otras marcas

AEG

AEG OMNI-JS Manual de usuario

SIP

SIP 01533 Manual de usuario

Ribimex

Ribimex PRS499 Manual de usuario

3M Fiber Optic Connector Crimp Tool Manual de usuario

Ryobi

Ryobi P524 Manual de usuario

ROJEK

ROJEK FSN 300A Manual de usuario

Kemper

Kemper 1740PRO Manual de usuario

WABCO

WABCO OptiTire Manual de usuario

EINHELL

EINHELL TE-MS 18/210 Li Manual de usuario

Orgapack

Orgapack OR-T 85 Guía rápida

TOUGHCUT

TOUGHCUT Diamond 400 Manual de usuario

Yaros

Yaros PB-3603 Manual de usuario

Fein

Fein BSS 2.0 E Guía de configuración

Baileigh Industrial

Baileigh Industrial SS-2725 Manual de usuario

Milwaukee

Milwaukee 2674-20 Manual de usuario

Fein

Fein BLs 1.6 Manual de usuario

Princess

Princess Electric Multi Sharpener Manual de usuario

FOREDOM

FOREDOM K.1050 Manual

Atlas Copco smartHEAD Manual de usuario

Manuales populares de Herramientas eléctricas de otras marcas