Atlanta Attachment Company 1347D Manual de usuario

Atlanta Attachment Company

362 Industrial Park Drive

Lawrenceville, GA 30046

770-963-7369 • www.atlatt.com

Technical Manual & Parts Lists

Model

1347D

Revision 9.1 Updated Sept 6, 2012

From the library of: Diamond Needle Corp

Technical Manual & Parts Lists

ATLANTA ATTACHMENT COMPANY,INC.

Confidential and Proprietary Information

The materials contained herein are confidential and proprietary information of Atlanta

Attachment Company. In addition to any confidentiality and non-disclosure obligations that currently

exist between you and Atlanta Attachment Company, your use of these materials serves as an

acknowledgment of the confidential and proprietary nature of these materials and your duty not to make

any unauthorized use or disclosure of these materials.

All materials contained herein are additionally protected by United States Copyright law and

may not be used, disclosed, reproduced, distributed, published or sold without the express written

consent of Atlanta Attachment Company, which consent may be withheld in Atlanta Attachment

Company’s sole discretion. You may not alter or remove any copyright, trademark or other notice from

copies of these materials.

Patents & Patents Pending

The sale of this product does not sell or otherwise transfer any license or other rights under any

U.S. Patent or other corresponding foreign patent.

This equipment is manufactured under one or more of the following patents:

4,280,421 ● 4,432,294 ● 4,466,367 ● 4,644,883 ● 5,134,947 ● 5,159,889 ● 5,203,270 ● 5,373,798 ●

5,437,238 ● 5,522,332 ● 5,524,563 ● 5,562,060 ● 5,634,418 ● 5,647,293 ●5,657,711 ● 5,743,202 ●

5,865,135 ● 5,899,159 ● 5,915,319 ● 5,918,560 ● 5,924,376 ●5,979,345 ● 6,035,794 ● 6,055,921 ●

6,202,579 ● 6,279,869 ● 6,295,481 ● 6,494,225 ●6,523,488 ● 6,574,815 ● 6,802,271 ● 6,834,603 ●

6,968,794 ● 6,994,043 ● 7,543,364 ●7,574,788 ● 7,647,876 ● 7,735,439

Foreign Patents: 9-520,472 ● 0,537,323 ● 92,905,522.6 ● 96,936,922.2 ● 2,076,379 ● 2,084,055

Other U.S. and Foreign Patents Pending.

IMPORTANT

It is important to read andunderstand the informationcontained withinthis

manual before attempting to operate the machine. Atlanta Attachment Co., Inc.

shall not be heldliable fordamage resulting frommisuse of the information

presented within, andreserves the right to change the informationcontained

within, without priornotification.

From the library of: Diamond Needle Corp

Technical Manual & Parts Lists

Contents

Important Safety Instruction....................................................................................................................... 1

Liability ...................................................................................................................................................... 2

Safety Equipment on the Machines ............................................................................................................ 3

Protective Eyewear ..................................................................................................................................... 4

Important Notices........................................................................................................................................ 5

Maintenance................................................................................................................................................ 7

Repair.......................................................................................................................................................... 8

A Word to the End User.............................................................................................................................. 9

Safety Precautions....................................................................................................................................... 9

Features..................................................................................................................................................... 10

General Machine Data .............................................................................................................................. 10

Operating Procedure ................................................................................................................................. 11

Controls and Adjustments......................................................................................................................... 12

Front of Control Box................................................................................................................................. 12

Manual Sew Pedals................................................................................................................................... 13

Folder/Head Adjustment........................................................................................................................... 13

Rewinder................................................................................................................................................... 13

Front Roll Holder...................................................................................................................................... 14

Troubleshooting........................................................................................................................................ 14

Thread Sensor Instructions ....................................................................................................................... 15

Clutch-Brake Installation & Maintenance ................................................................................................ 16

Installation................................................................................................................................................. 16

Airline Connections.................................................................................................................................. 17

Lubrication................................................................................................................................................ 17

Parts Replacement..................................................................................................................................... 17

Clutch Parts List........................................................................................................................................ 19

1347D Puller Motor Parameter List.......................................................................................................... 20

1347D Sewing Head Parameter List......................................................................................................... 21

Electric Eye Sensor Adjustment ............................................................................................................... 22

Reflective Tape Maintenance ................................................................................................................... 22

Recommended Spare Parts List................................................................................................................ 22

AAC Part # SP1347D Spare Parts Kit...................................................................................................... 22

Assembly Drawings & Parts Lists............................................................................................................ 24

11347D Faux Pillowtop Border Workstation........................................................................................... 26

1347010 Sew Head Assembly.................................................................................................................. 27

1347030 Swing Out Binder Assembly ..................................................................................................... 28

From the library of: Diamond Needle Corp

Technical Manual & Parts Lists

1347040 Swing Out Binder Assembly ..................................................................................................... 29

1347126 Motor / Tensioner Assembly ..................................................................................................... 30

1347065 Right Side Folder Assembly...................................................................................................... 32

1347079 Left Side Folder Assembly ........................................................................................................ 34

1347080 Binding Roll Support................................................................................................................. 36

1347090 Binding Roll Support................................................................................................................. 38

1347094 Upper Tension Assembly........................................................................................................... 40

1347098 Rewind Assembly w/ Sleeve ..................................................................................................... 42

1347110 Main Frame Assembly............................................................................................................... 44

1347127 Head Mount Assembly .............................................................................................................. 46

1961-900C Control Box Assembly........................................................................................................... 48

1961-300EB Worm Gear Puller Assembly, 18”....................................................................................... 50

1961-250F Prefeed Assembly................................................................................................................... 52

33008708 Ball Bearing Disc Assembly.................................................................................................... 53

1347D-PD Pneumatic Diagram ................................................................................................................ 55

1347D-WD Control Wiring Diagram....................................................................................................... 56

From the library of: Diamond Needle Corp

Technical Manual & Parts Lists

Important Safety Instruction

This part of the Instruction Material is provided for the safe use of your equipment.

It contains important information to help work safely with the unit and describes the

dangers inherent in machinery. Some of these dangers are obvious, while others are

less evident.

Mandatory Information

All persons operating and/or working on the 1347D should read and understand all parts of the Safety

Instructions. This applies, in particular, for persons who only operate and/or work on the unit

occasionally (e.g. for maintenance and repair). Persons who have difficulty reading must receive

particularly thorough instruction.

Scope of the Instruction Material

The Instruction Material comprises:

Safety information

Operator Instructions

Electrical and Pneumatic diagrams

And may also include;

A list of recommended spare parts

Instruction Manual(s) for components made by other manufacturers

The layout and installation diagram containing information for installation

Intended Use

Our machines are designed and built in line with the state of the art and the accepted safety rules.

However, all machines may endanger the life and limb of their users and/or third parties and be damaged

or cause damage to other property, particularly if they are operated incorrectly or used for purposes

other than those specified in the Instruction Manual.

Exclusion of Misuse

Non-conforming uses include, for example, using the equipment for something

other than it was designed for, as well as operation without duly installed safety

equipment. The risk rests exclusively with the end user.

Conforming use of the machine includes compliance with the technical data,

information and regulations in all parts of the complete Instruction Material, as

well as compliance with the maintenance regulations. All local safety and

accident prevention regulations must also be observed.

From the library of: Diamond Needle Corp

Technical Manual & Parts Lists

Liability

The machine should only be operated when in perfect working order, with due regard for safety and the

potential dangers, as well as in accordance with the Instruction Material. Faults and malfunctions

capable of impairing safety should be remedied immediately. We cannot accept any liability for personal

injury or property damage due to operator errors or non-compliance with the safety instructions

contained in this booklet. The risk rests exclusively with the end user.

The Instruction Material should always be kept near the machine so that it is accessible to all concerned.

The local, general, statutory and other binding regulations on accident prevention and environmental

protection must also be observed in addition to the Instruction Material. The operating staff must be

instructed accordingly. This obligation also includes the handling of dangerous substances and

provision/use of personal protective equipment.

The Instruction Material should be supplemented by instructions, including supervisory and notification

duties with due regard for special operational features, such as the organization of work, work

sequences, the personnel deployed, etc.

The personnel's awareness of the dangers and compliance with the safety regulations should be checked

at irregular intervals.

Choice and Qualification of Personnel

Ensure that work on the machine is only carried out by reliable persons who have been appropriately

trained for such work - either within the company, by our field staff or at our office - and who have not

only been duly appointed and authorized, but are also fully familiar with the local regulations. Work on

the machine should only be carried out by skilled personnel, under the management and supervision of a

duly qualified engineer.

This not only applies when the machine is used for production, but also for special work associated with

its operation (start-up and maintenance), especially when it concerns work on the hydraulic or electrical

systems, as well as on the software/serial bus system.

Training

Everyone working on or with the machine should be duly trained and informed with regard to correct

use of the safety equipment, the foreseeable dangers which may arise during operation of the machine

and the safety precautions to be taken. In addition, the personnel should be instructed to check all safety

mechanisms at regular intervals.

Responsibilities

Clearly define exactly who is responsible for operating, setting-up, servicing and repairing the machine.

Define the responsibilities of the machine operator and authorize him to refuse any instructions by third

parties if they run contrary to the machine's safety. This applies in particular for the operators of

machines linked to other equipment. Persons receiving training of any kind may only work on or with

the machine under the constant supervision of an experienced operator. Note the minimum age limits

permitted by law.

From the library of: Diamond Needle Corp

Technical Manual & Parts Lists

A Word to the Operator

The greatest danger inherent in our machines:

is that of fingers, hands or loose clothing being drawn into a machine by live, coasting or rotating tools

or assemblies or of being cut by sharp tools or burned by hot elements.

ALWAYS BE CONSCIOUS OF THESE DANGERS!

Safety Equipment on the Machines

All machines are delivered with safety equipment, which shall not be removed or

bypassed during operation.

The correct functioning of safety equipment on machines and systems should be

checked every day and before every new shift starts, after maintenance and repair

work, when starting up for the first time and when restarting (e.g. after prolonged

shutdowns).

If safety equipment has to be dismantled for setting-up, maintenance or repair work, such safety

equipment shall be replaced and checked immediately upon completing the maintenance or repair work.

All protective mechanisms shall be fitted and fully operational whenever the machine is at a standstill or

if it has been shut down for a longer period of time.

Damage

If any changes capable of impairing safety are observed in the machine or its mode of operation, such as

malfunctions, faults or changes in the machine or tools, appropriate steps must be taken immediately, the

machine switched off and a proper lockout tagout procedure followed. The machine should be examined

for obvious damage and defects at least once per shift. Damage found shall be immediately remedied by

a duly authorized person before resuming operation of machine.

The machine should only be operated when in perfect working order and when all protective

mechanisms and safety equipment, such as detachable protective mechanisms, emergency STOP

systems, etc. are in place and operational.

Faults or Errors

The machine must be switched off and all moving or rotating parts allowed to come to a standstill and

secured against accidental restart before starting to remedy any faults or errors.

Signs on the Machine

Safety and danger signs on the machine should be observed and checked at regular intervals to ensure

that they are complete and undamaged. They should be clearly visible and legible at all times.

Clothing, Jewelry, Protective Equipment

Long loose hair, loose-fitting clothes, gloves and jewelry, including rings, should be avoided in order to

avoid injuries due to being caught, drawn in and wound up inside the machine.

From the library of: Diamond Needle Corp

Technical Manual & Parts Lists

Protective Eyewear

Protective eyewear that has been tested by the local authorities should be worn

whenever there is a possibility of loose or flying objects or particles such as when

cleaning the machine with compressed air.

Tools

Always count the number of tools in your possession before starting work on the machine. This will

allow you to check that no tools have been left behind inside the machine. Never leave a tool in the

machine while working.

Oils, Lubricants, Chemicals

Note the applicable safety regulations for the product used.

No Smoking, Fire, Explosion Hazard

Smoking and open flame (e.g. welding work) should be prohibited in the production area due to the risk

of fire and explosions.

Workplace

A clear working area without any obstructions whatsoever is essential for safe operation of the machine.

The floor should be level and clean, without any waste.

The workplace should be well lit, either by the general lighting or by local lights.

Emergency STOP

The emergency STOP buttons bring all machine movements to a standstill. Make sure you know exactly

where they are located and how they work. Try them out. Always ensure easy access to the nearest

emergency STOP button while working on the machine.

First Aid

1. Keep calm even when injured.

2. Clear the operator from the danger zone. The decision of what to do and whether to seek

additional assistance rests entirely with you, particularly if someone has been trapped.

3. Give First Aid. Special courses are offered by such organizations as the employers' liability

insurance association. Your colleagues should be able to rely on you and vice versa.

4. Call an ambulance. Do you know the telephone numbers for the ambulance service, police and

fire service?

From the library of: Diamond Needle Corp

Technical Manual & Parts Lists

Important Notices

Reporting and Fighting Fires

Read the instructions posted in the factory with regard to reporting fires and the emergency exits. Make

sure you know exactly where the fire extinguishers and sprinkler systems are located and how they are

operated. Pass on the corresponding information to the firemen when they arrive. Ensure there are

enough signs to avoid fire hazards.

The following fire extinguishers may be used:

- Dry powder extinguishers, ABC fire-extinguishing powder.

- Carbon dioxide fire extinguishers to DIN 14461 for electronic components. Great care must be

exercised when using carbon dioxide fire extinguishers in confined, badly ventilated rooms (see DIN

14406 and 14270).

Isolate the machine from the power supply if a fire breaks out. Do not use water on burning electrical

parts until it is absolutely certain that they have been completely disconnected from the power supply.

Burning oils, lubricants, plastics and coatings on the machine can give off gases and vapors that may be

harmful to your health.

A qualified person should be consulted to repair the damage after a fire.

Electrical Power Supply

Before undertaking any maintenance or repair work on the machine, switch off the

electrical power to the machine at the main source and secure it with a padlock so

that it cannot be switched on again without authorization.

In practice, this may mean that the technician, electrician and operator all attach

their own padlock to the master switch simultaneously so that they can carry out

their work safely. Locking extension plates should be available for multiple locks if

required. The primary purpose for a lockout/tagout procedure is to protect workers

from injury caused by unexpected energizing or start-up of equipment.

Energy sources (electrical/pneumatic/hydraulic, etc.) for the equipment shall be turned off or

disconnected and the switches locked or labeled with a warning tag. It is the responsibility of the

employer to establish control procedures. Follow lockout/tagout procedures before, setup and/or any

service or maintenance work is performed, including lubrication, cleaning or clearance of jams.

Caution: The machine is still not completely de-energized even when the master

switch is off.

- Electricity - The machine is always isolated from the electrical power supply whenever the master

switch has been switched off. However, this does not apply for the power supply in the control cabinet,

nor for equipment that does not draw its power via the master switch.

- Pneumatic / hydraulic energy - Almost all our machines carry compressed air. In addition to switching

off the master switch, the air supply must also be disconnected and the machine checked to ensure it is

depressurized before starting any work on the machine; otherwise the machine may execute

uncontrolled movements.

From the library of: Diamond Needle Corp

Tabla de contenidos

Otros manuales de Máquina de coser de Atlanta Attachment Company

Atlanta Attachment Company

Atlanta Attachment Company 1392D Manual de usuario

Atlanta Attachment Company

Atlanta Attachment Company 3200PC Manual de usuario

Atlanta Attachment Company

Atlanta Attachment Company 1335MH Manual de usuario

Atlanta Attachment Company

Atlanta Attachment Company 4300AC Manual de usuario

Atlanta Attachment Company

Atlanta Attachment Company 1335E Manual de usuario

Atlanta Attachment Company

Atlanta Attachment Company 1344S88 Manual de usuario

Atlanta Attachment Company

Atlanta Attachment Company 1393BSW Manual de usuario

Atlanta Attachment Company

Atlanta Attachment Company 4300A Manual de usuario

Atlanta Attachment Company

Atlanta Attachment Company 1335MFB Manual de usuario

Atlanta Attachment Company

Atlanta Attachment Company 1335MGB Manual de usuario

Atlanta Attachment Company

Atlanta Attachment Company 1342TA Manual de usuario

Atlanta Attachment Company

Atlanta Attachment Company 1335MF Manual de usuario

Atlanta Attachment Company

Atlanta Attachment Company 1339HFJ Manual de usuario

Atlanta Attachment Company

Atlanta Attachment Company 1347MA Manual de usuario

Atlanta Attachment Company

Atlanta Attachment Company 1335MDS Manual de usuario

Atlanta Attachment Company

Atlanta Attachment Company 1345-6A Manual de usuario

Atlanta Attachment Company

Atlanta Attachment Company 1330K Manual de usuario

Atlanta Attachment Company

Atlanta Attachment Company 1342ZTC Manual de usuario

Atlanta Attachment Company

Atlanta Attachment Company 1393E Manual de usuario

Atlanta Attachment Company

Atlanta Attachment Company 1355R Manual de usuario

Atlanta Attachment Company

Atlanta Attachment Company 1335MHB Manual de usuario

Atlanta Attachment Company

Atlanta Attachment Company 1330E Manual de usuario

Atlanta Attachment Company

Atlanta Attachment Company 1337HEH Manual de usuario

Atlanta Attachment Company

Atlanta Attachment Company 1347MTA Manual de usuario

Manuales populares de Máquina de coser de otras marcas

Riccar

Riccar RL634DE Manual de usuario

Singer

Singer 2517 Manual de usuario

Pfaff

Pfaff 3307-1 SERIES Manual de usuario

Janome

Janome Quilt Maker Pro 18 VERSA Manual de usuario

Siruba

Siruba C007JP Manual de usuario

Husqvarna Viking

Husqvarna Viking Designer SE Manual de usuario

Singer

Singer 148-5 Manual de usuario

IKEA

IKEA SY Manual de usuario

Pfaff

Pfaff 571 Manual de usuario

Singer

Singer 15-91 Manual de usuario

Brother

Brother BB370 Manual de usuario

Pegasus

Pegasus WT100 Series Manual de usuario

Reliable

Reliable 7100DB Manual de usuario

Pfaff

Pfaff 937 Manual de usuario

Singer

Singer 6038 Manual de usuario

Singer

Singer 413K Manual de usuario

Pfaff

Pfaff 1471 E1 Manual de usuario

Kenmore

Kenmore 16677 - Serger Sewing Machine Manual de usuario