Mappin g Port F lash
POE
Scan
Menu
Length
Ping
Scan
Scanning...
button on the receiver used to control lighting and detect currency;
button is sensitivity control when you find the cables.
The receiver charge : when connected the receiver charge , The light will
shining near the MICRO , and the same time , the charge Indicator light will
flashing , after full of power , this light will always lit.
21
Scan
Scanning. ..
--POE switch--
d. Cable scanning
The advanced version ATD8601, it has three modes for option.
(Low frequency, PoE switch, High frequency)
Firstly, choose icon “SCAN” on the main menu (Graph 1), enter to a default
scan mode, which is “low frequency” mode (Graph 2). Press “Up\Down”
button to switch scan modes to “PoE switch “ (Graph 3) or “High frequency”
(Graph 4) mode according to your
working environments.
Scan
Scanning...
--High frequency--
Graph 1
Graph 2
Graph 3
Graph 4
--low frequency--
Caution:
1. The scan mode in the tranmistter and receiver must be same, If the modes are not
matched correctly,even the receiver touch the correct cable, it won't generate tone,
either. (How to match the mode accordingly, see the following part of “usage of receiver”)
2. Users must choose “PoE switch” mode if scan cables connected to PoE switch.
Press to turn on the receiver, the “power” indicator is lit on, which
means it works normally. “SET” button is for choosing scan modes or voltage
detecting.
a) Short press “SET” one time, the “ SCAN” indicator will turn red, in this
situation, it is available for two scan modes: Low frequency / PoE switch.
It means, when the “scan” indicator is red, users must choose “ Low frequency”
or “PoE switch” mode in the transmitter.
b) Short press “SET” two times, the “ SCAN” indicator will turn purple, in this
situation, it is only available for “High frequency “ mode. It means, when the
“scan” indicator is purple, users must choose “ High frequency” mode in the
transmitter.
c) Long press “SET” for 2-3 secs, the “NCV” indicator will turn red, in this
situation, the receiver can be used as a voltage detector.
Usage of Receiver
1. Tracing Telephone /Lan cable which is connected to switch or router.
Insert the cable into port “RJ11”/ “RJ45 Scan”, enter “SCAN” menu to choose
“Low frequency” mode . Then turn on the receiver, press “SET” button one time
until the “SCAN” indicator turn red, then go to the other side to trace the target
cable.
(Note: telephone cable into “RJ11” port, Lan cable into “RJ45 Scan” port)
2. Tracing Coax cable
Insert the cable into port “BNC”, enter “SCAN” menu to choose “Low
frequency” mode . Then turn on the receiver, press “SET” button one
time until the “SCAN” indicator turn red, then go to the other side to trace
the target cable.
22
Mappin g Port F lash
POE
Scan
Menu
Length
Ping
Connection diagram of crosstalk line pair
1
2
3
6
4
5
7
8
1
2
3
6
4
5
7
8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8 G
M:
R:
1 2 3 4 5 6 7 8 G
e. Crosstalk test
As shown the figure below: it shows 3, 6 and 4, 5 with crosstalk. The line
pair With crosstalk will flash to indicate failure. If the testing cable is
crosstalk, Which will slow down the network speed:
Crosstalk interface is shown as below:
Note: In case of the non-twisted-pair cable like telephone cable,
Due to over large crosstalk, it generally shown as crosstalk.
f. POE test
After enter the main menu , press this cursor to move , and
point to POE test menu , and press OK to test POE; Take one side insert
the “POE/Ping “ PORT , the other side insert into POE Router or Ethernet ,
then start testing , and press OK , the screen will show you the voltage of
each pin.
23 24
RJ45 Mapping
Test mode : Remote
Data upl oad
Start
POE
Cross over:3 4 5 6
crossover pins flicker
1
2
3
4
5
6
7
8
50.0V
50.0V
0.0V
0.0V
POE
Tseting ...
POE
Mappin g Port F lash
POE
Scan
Menu
Length
Ping
Data upload
Start
POE
Data saved to:POE.TXT
Ping
Config ure
Ping
Ping
Ping Data upl oad
Data saved to：PING.TXT
If you want to save the tested result, you can choose data export into the
TF card, the picture show you as below:
g. PING test:
After enter the main menu , press this cursor to move to “Ping”
test , and press OK to test Ping; Take one side insert the “PING “ PORT ,
the other end connect to router or switcher , then start testing,the screen
will show you the test result as below.
If you want to save the tested result, you can choose data export into the
TF card and choose “PING.TXT”, the picture show you as below:
POE Data upload
Pi ng 1 92 .1 68 .1 .1 w it h 32 b yt es o f da ta :
Re pl y fr om 1 92 .1 68 .1 .1 : ti me =1 ms T TL=64
Re pl y fr om 1 92 .1 68 .1 .1 : ti me =1 ms T TL=64
Re pl y fr om 1 92 .1 68 .1 .1 : ti me =1 ms T TL=64
Re pl y fr om 1 92 .1 68 .1 .1 : ti me =1 ms T TL=64
Ping stat is ti cs f or 19 2. 16 8. 1. 1
Packets : Se nt =4 , Re ce iv ed =4 , Lo st =0
Approxi ma te r ou nd t ri p ti me s in m s:
Min=1ms , Max=1ms , Average=1ms
Ping
Config ure
Ping
Data upl oad
Start
Ping
De st in ati on I P: 192 .1 68 .1. 1
Data upload
St ar t
Ping
De st in ati on I P: 192 .1 68 .1. 1
Mapping Por t Fla sh
POE
Scan
Menu
Length
Ping
Mappin g Port F lash
POE
Scan
Menu
Length
Ping
Parameter specification of PING functions
IP address: can obtain automatically any Internet device which has
connected in the global. (Under a specific situation, users need to manually set
IP address when can't be automatically obtain IP address.)
Local IP address:It can be set up,but it must be different with other LAN devices.
Default gateway / Router: In the local LAN Router or gateway IP address.
Subnet mask: In the local LAN Subnet mask Remark :
Default gateway or Router or Subnet mask can be found by the same LAN
internet; Start – operate – impute CMD, Start the command line program ,
after that type “ ipconfig “ can query it.
Data packet: can be set based on needs.
