Asus VX97 Manual de usuario

VX97 User’s Manual 1

VX97 USER'S MANUAL

User's Notice

No part of this product, including the product and software may be reproduced,

transmitted, transcribed, stored in a retrieval system, or translated into any language

in any form by any means without the express written permission of ASUSTeK

COMPUTER INC. (hereinafter referred to asASUS) except documentation kept by

the purchaser for backup purposes.

ASUS provides this manual "as is" without warranty of any kind, either express or

implied, including but not limited to the implied warranties or conditions of merchant-

ability or fitness for a particular purpose. In no event shallASUS be liable for any loss

or profits, loss of business, loss of use or data, interruption of business, or for indirect,

special, incidental, or consequential damages of any kind, even if ASUS has been

advised of the possibility of such damages arising from any defect or error in this

manual or product. ASUS may revise this manual from time to time without notice.

Products mentioned in this manual are mentioned for identification purposes only.

Product names appearing in this manual may or may not be registered trademarks or

copyrights of their respective companies.

The product name and revision number are both printed on the board itself. Manual

revisions are released for each board design represented by the digit before and after

the period of the manual revision number. Manual updates are represented by the

third digit in the manual revision number.

Product Name: VX97

Manual Revision: 1.01

Release Date: January 1997

2 VX97 User’s Manual

FCC & DOC COMPLIANCE

FederalCommunicationsCommissionStatement

This device complies with FCC Rules Part 15. Operation is subject to the following

two conditions:

• This device may not cause harmful interference, and

• This device must accept any interference received, including interference that

may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installa-

tion. This equipment generates, uses and can radiate radio frequency energy and, if

not installed and used in accordance with manufacturer's instructions, may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interfer-

ence by one or more of the following measures:

• Re-orient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment to an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

WARNING: The use of shielded cables for connection of the monitor to the graph-

ics card is required to assure compliance with FCC regulations. Changes or modifi-

cations to this unit not expressly approved by the party responsible for compliance

could void the user's authority to operate this equipment.

CanadianDepartmentofCommunicationsStatement

This digital apparatus does not exceed the Class B limits for radio noise emissions

from digital apparatus set out in the Radio Interference Regulations of the Canadian

Department of Communications.

VX97 User’s Manual 3

How this manual is organized

This manual is divided into the following sections:

I. Introduction: Manual information and checklist

II. Features: Information and specifications concerning this product

III. Installation: Instructions on setting up the motherboard.

IV. BIOS Setup: BIOS software setup information.

V. DMI Utility: BIOS supported Desktop Management Interface

Item Checklist

Please check that your package is complete. If you discover damaged or missing

items, please contact your retailer.

√The VX97 motherboard

√2 serial port ribbon cables attached to a mounting bracket

√1 parallel ribbon cable with mounting bracket

√1 IDE ribbon cable

√1 floppy ribbon cable

√Support drivers and utilities as follows (view FILELIST.TXT for details)

• Flash Memory Writer utility to update the FLASH BIOS

• Desktop Management Interface (DMI) utility

• Bus Master IDE Drivers for various operating systems

• Readme files for descriptions and use of the files

√This user's manual

Optional PS/2 mouse cable with mounting bracket

Optional infrared module

I. INTRODUCTION

(Manual / Checklist)

4 VX97 User’s Manual

Features of the VX97 Motherboard

The VX97 is carefully designed for the demanding PC user who wants a great many

features in a small package. This motherboard:

•Easy Installation: Is equipped with BIOS that supports auto detection of hard

drives, PS/2 mouse, and Plug and Play devices to make setup of hard drives,

expansion cards, and other devices virtually automatic.

•Multi-Processor/Multi-Speed Support: Supports one Intel Pentium

75-200MHz (P55C-MMX, P54C/P54CS), Cyrix P166+ (Rev 2.7 or later), or

AMD-K5 (PR75-133MHz) (See page 8).

•Intel Chipset: Features Intel's 430VX PCIset with I/O subsystems.

•Desktop Management Interface (DMI): Supports DMI through BIOS which

allows hardware to communicate within a standard protocol creating a higher

level of compatibility. (Requires DMI-enabled components.) (See section V)

•L2 Cache: Comes in 256KB or 512KB models.

•Versatile DRAM Memory Support: Supports 72-pin SIMMs of 4MB, 8MB,

16MB, or 32MB to form a memory size between 8MB to 128MB. Supports

both Fast Page Mode (FPM) and Extended Data Output (EDO) SIMMs.

•ISA and PCI Expansion Slots: Provides three PCI slots, three ISA slots, and one

PCI/ISA share slot.

•Super Multi-I/O: Provides two high-speed UART compatible serial ports and

one parallel port with EPP and ECP capabilities. UART2 can also be directed

from COM2 to the Infrared Module for wireless connections. Two floppy drives

of either 5.25" or 3.5" (1.44MB or 2.88MB) are also supported without an exter-

nal card. The Japanese "Floppy 3 mode" (3.5" 1.2MB) floppy standard is

also supported.

•PCI Bus Master IDE Controller: Comes with an onboard PCI Bus Master

IDE controller with two connectors that supports four IDE devices in two chan-

nels, provides faster data transfer rates, and supports Enhanced IDE devices

such as Tape Backup and CD-ROM drives. This controller supports PIO Modes

3 and 4 and Bus Master IDE DMA Mode 2. BIOS now supports IDE CD-

ROM or SCSI bootup.

•Optional IrDA and PS/2 Mouse Connector: This motherboard supports an

optional infrared port module for wireless interface and a PS/2 mouse cable set.

•NCR SCSI BIOS: This motherboard has firmware that supports optional NCR

SCSI controller cards.

II. FEATURES

(Features)

II. FEATURES

VX97 User’s Manual 5

Parts of the VX97 Motherboard

II. FEATURES

(Parts of Board)

WARNING: Computer motheboards and components contain very delicate

Integrated Circuit (IC) chips. To protect the motherboard and other compo-

nents against damage from static electricity, you should follow some precau-

tions whenever you work on your computer.

1. Unplug your computer when working on the inside.

2. Hold components by the edges and try not to touch the IC chips, leads, or

circuitry.

3. Use a grounded wrist strap before handling computer components.

4. Place components on a grounded antistatic pad or on the bag that came with

the component whenever the components are separated from the system.

Intel's 430VX

PCIset

256KB/ 512KB L2 Cache

CPU ZIF

Socket 7

(4) 72-pin SIMM

Sockets

3ISASlots

3 PCI Slots

1 PCI/ISA

Share Slot

Programmable

Flash ROM Super Multi-I/O Serial/Parallel Ports

IDE/Floppy

6 VX97 User’s Manual

III. INSTALLATION

Map of the VX97 Motherboard

ISA Slot 3

ISA Slot 2

ISA Slot 1

PCI Slot 4

PCI Slot 3

PCI Slot 2

PCI Slot 1

FS0

FS1

FS2

BUS FREQ

Board Power Input

P8 P9

Primary IDE

Secondary IDE

Universal Serial

Bus (Reserved)

PS/2 Mouse

Floppy Drives

Keyboard

SIMM Socket 1 (Bank 0)

SIMM Socket 2 (Bank 0)

SIMM Socket 3 (Bank 1)

SIMM Socket 4 (Bank 1)

CPU ZIF Socket 7

Infrared Con.

Panel Connections

RTC Clear

IDE LED

Parallel Port (Printer)

Serial Ports

COM 2

COM 1

ISA Slot 4

256/512KB OnBoard L2 Cache

VID2

VID1

VID0

BF0

BF1

BUS Ratio

BBLKW

Block Program (Dis/En)

Keyboard BIOS

Flash ROM for BIOS

Intel 430VX

PCIset

Intel PIIX3

PCIset

CPU Voltage ID

CR2032

3V Lithium Cell

(RTC RAM

Memory)

(Map of Board)

III. INSTALLATION

System Memory (SIMM)

IMPORTANT: Banks 0 & 1 must have the same size memory installed in pairs.

Do not use memory modules with more than 24 chips per module. Modules with

more than 24 chips exceed the design specifications of the memory subsystem and

will be unstable. Memory speed setup is required through "Auto Configuration"

in BIOS Chipset Setup of the BIOS SOFTWARE.

Install memory in any or all of the banks in any combination as follows:

Bank Memory Module Total Memory

Bank 0 4MB, 8MB, 16MB, 32MB x2

SIMM Sockets 1&2 72-pin FPM or EDO SIMM

Bank 1 4MB, 8MB, 16MB, 32MB x2

SIMM Sockets 3&4 72-pin FPM or EDO SIMM

Total System Memory (Max 128MB) =

VX97 User’s Manual 7

III. INSTALLATION

Jumpers

1. Flash ROM Boot Block Programming (BBLKW)

This sets the operation mode of the boot block area of the Programmable Flash

ROM to allow programming in the Enabled position. This is required only if

prompted by the FlashMemoryWriterUtilityas shown in BIOS SOFTWARE.

Boot Block Programming (Disable / Enable)

Disabled / Protected

(Default) Enabled

BBLKW 1

BBLKW

2. Real Time Clock (RTC) RAM

This clears the user-entered information stored in the CMOS RAM of the Real

Time Clock such as hard disk information and passwords. To clear the RTC

data: (1) Turn off the PC, (2) Short this jumper, (3) Power on the PC, (4) Turn

off the PC, (5) Remove this jumper, (6) Power on the PC, (7) Hold down

<Delete> during bootup and enter BIOS setup to re-enter user preferences.

RTC RAM (Operation / Clear Data)

Operation (Default) Clear Data

3. Voltage Regulator Output Selection (VID0, VID1, VID2)

Intel P54C Pentium

(75-200MHz) Intel P55C Pentium

MMX (200MHz) AMD-K5

(PR75-133MHz) Cyrix 6x86 166+

Rev2.7 (133MHz)

Voltage Regulator Output Selection

2.5V

AMD3

VID1

VID2

VID0

2.7V

AMD1 2.8V

P55C 2.9V

AMD2 3.4V

STD 3.5V

VRE

321 321 321 321 321 321

(Jumpers)

III. INSTALLATION

8 VX97 User’s Manual

III. INSTALLATION

(Jumpers)

III. INSTALLATION

4. CPU External (BUS) Frequency Selection (FS0, FS1, FS2)

These jumpers tell the clock generator what frequency to send to the CPU. These

allow the selection of the CPU’s External frequency (orBUS Clock). The BUS Clock

timesthe BUSRatio equalsthe CPU'sInternal frequency(the advertisedCPU speed).

5. CPU to BUS Frequency Ratio (BF0, BF1)

These jumpers set the frequency ratio between the Internal frequency of the CPU

and the External frequency (called the BUS Clock) within the CPU. These must

be set together with the above jumpers CPU External (BUS) Frequency Selection.

50MHz 55MHz 60MHz 66MHz

CPU External Clock (BUS) Frequency Selection

FS1

FS0

FS2

FS1

FS0

FS2

FS1

FS0

FS2

FS1

FS0

FS2

CPU : BUS Frequency Ratio

1.5x (3/2)

BF1

BF0

2.0x(2/1)

BF1

BF0

2.5x (5/2)

BF1

BF0

3.0x (3/1)

BF1

BF0

3.0x (3/1) 2.0x(2/1) 1.0x (1/1) 4.0x (4/1)

Intel

Cyrix

Set the jumpers by the Internal speed of the Intel, AMD, or Cyrix CPU as follows:

(BUS Freq.) (Freq. Ratio)

CPU Model Freq. Ratio BUS Freq. FS2 FS1 FS0 BF1 BF0

Intel Pentium 200MHz 3.0x 66MHz [2-3] [1-2] [2-3] [2-3] [1-2]

Intel Pentium 166MHz 2.5x 66MHz [2-3] [1-2] [2-3] [2-3] [2-3]

Intel Pentium 150MHz 2.5x 60MHz [2-3] [2-3] [1-2] [2-3] [2-3]

Intel Pentium 133MHz 2.0x 66MHz [2-3] [1-2] [2-3] [1-2] [2-3]

Intel Pentium 120MHz 2.0x 60MHz [2-3] [2-3] [1-2] [1-2] [2-3]

Intel Pentium 100MHz 1.5x 66MHz [2-3] [1-2] [2-3] [1-2] [1-2]

Intel Pentium 90MHz 1.5x 60MHz [2-3] [2-3] [1-2] [1-2] [1-2]

Intel Pentium 75MHz 1.5x 50MHz [2-3] [2-3] [2-3] [1-2] [1-2]

AMD-K5-PR133 100MHz 1.5x 66MHz [2-3] [1-2] [2-3] [1-2] [1-2]

AMD-K5-PR120 90MHz 1.5x 60MHz [2-3] [2-3] [1-2] [1-2] [1-2]

AMD-K5-PR100 100MHz 1.5x 66MHz [2-3] [1-2] [2-3] [1-2] [1-2]

AMD-K5-PR90 90MHz 1.5x 60MHz [2-3] [2-3] [1-2] [1-2] [1-2]

AMD-K5-PR75 75MHz 1.5x 50MHz [2-3] [2-3] [2-3] [1-2] [1-2]

*Cyrix 166+ 133MHz 2.0x 66MHz [2-3] [1-2] [2-3] [1-2] [2-3]

*NOTE: Only Cyrix Revision 2.7 or later is supported on this motherboard. See previous page for

revision identification. Bootup screen will show 6x86-P166+ -S CPU at 133MHz with the

Cyrix 166+ installed on this motherboard.

Compatible Cyrix CPU Identification

The only Cyrix CPU that is supported on this motherboard is

labeled Cyrix 6x86 P166+ but must be Revision 2.7 and later.

Look on the underside of the CPU for the serial number. The

number should read G8DC6620Aor larger.

VX97 User’s Manual 9

III. INSTALLATION

External Connectors

IMPORTANT: Ribbon cables should always be connected with the red stripe on

the Pin 1 side of the connector. The four corners of the connectors are labeled on

the motherboard. Pin 1 is the side closest to the power connector on hard drives

and floppy drives. IDE ribbon cable must be less than 18in. (46cm), with the

second drive connector no more than 6in. (15cm) from the first connector.

1. Keyboard Connector (5-pin female)

This connection is for a standard IBM-compatible keyboard. May also be known

as a 101 enhanced keyboard.

Keyboard Connector (5-pin female)

This motherboard accepts an AT Keyboard

Connector Plug as shown here.

Keyboard Connector

2. PS/2 Mouse Connector (6-pin block)

If you are using a PS/2 mouse, you must purchase an optional PS/2 mouse set

which connects to the 6 pin block and mounts to an open slot on your computer's

case. The system will direct IRQ12 to the PS/2 mouse if one is detected. If not

detected, expansion cards can use IRQ12. Use “PS/2 Mouse Control” in BIOS

Features Setup of the BIOS SOFTWARE for settings.

1: GND

2: DATA

3: NC

4: VCC

5: CLK

8: NC

134

This optional PS/2 mouse cable

and bracket set is necessary to

provide a connector for a PS/2

mouse on a free expansion slot

cover.

(Motherboard)

(Cable Set)

PS/2 Mouse Module Connector

(Connectors)

III. INSTALLATION

WARNING: Some pins are used for connectors or power sources. These are

clearly separated from jumpers in "Map of the Motherboard". Placing jumper

caps over these will cause damage to your motherboard.

10 VX97 User’s Manual

III. INSTALLATION

3. Parallel Printer Connector (26 Pin Block)

Connection for the included parallel port ribbon cable with mounting bracket.

Connect the ribbon cable to this connection and mount the bracket to the case on

an open slot. It will then be available for a parallel printer cable. You can enable

the parallel port and choose the IRQ through "Onboard Parallel Port" in Chipset

Features of the BIOS SOFTWARE.

arallel (Printer) Connector

Pin 1

For this connector to be available, you must connect

the included Parallel (25-Pin female) cable set to a

free expansion slot opening.

TIP: You may also remove the bracket connectors

and mount them directly to the case to save expansion

slot space.

4. Serial Port COM1 and COM2 Connectors (Two 10-pin blocks)

These connectors support the provided serial port ribbon cables with mounting

bracket. Connect the ribbon cables to these connectors and mount the bracket to

the case on an open slot. The two serial ports on the mounting bracket will then

be used for pointing devices or other serial devices. See "Onboard Serial Port"

in Chipset Features Setup of the BIOS SOFTWARE for settings.

Serial Port Connectors

COM 1 COM 2

Pin 1 Pin 1

For these connectors to be available, you must connect

the included Serial cable set from COM1 (using the

9-Pin male) & COM2 (using the 25-Pin male) to a free

expansion slot opening.

TIP: You may also remove the bracket connectors

and mount them directly to the case to save expansion

slot space.

5. Floppy drive connector (34-pin block )

This connector supports the provided floppy drive ribbon cable. After connect-

ing the single end to the board, connect the two plugs on the other end to the

floppy drives.

Floppy Drive Connector

Connect the Red stripe to Pin 1

Pin 1

(Connectors)

III. INSTALLATION

Otros manuales para VX97

Tabla de contenidos

Otros manuales de Placa madre de Asus

Asus

Asus H310I-IM-A R2.0 Manual de usuario

Asus

Asus P8B75-M LE Manual de usuario

Asus

Asus STRIX Z270G GAMING Manual de usuario

Asus

Asus M2V-TVM Manual de usuario

Asus

Asus Motherboard A7S8X-MX Manual de usuario

Asus

Asus Motherboard PR-DLS533 Manual de usuario

Asus

Asus P5K - AiLifestyle Series Motherboard Manual de usuario

Asus

Asus Prime H510M-A Manual de usuario

Asus

Asus P5L-MX IPAT Manual de usuario

Asus

Asus PRIME B650M-A WIFI Manual de usuario

Asus

Asus F1A75-M Manual de usuario

Asus

Asus P8Z77-I DELUXE/WD Manual de usuario

Asus

Asus Z97-E/USB3.1 Manual de usuario

Asus

Asus TUF GAMING B760M-E D4 Manual de usuario

Asus

Asus TUF GAMING B760M-BTF WIFI D4 Manual de usuario

Asus

Asus P2B Manual de usuario

Asus

Asus H81M-CS Manual de usuario

Asus

Asus P5QL PRO - Motherboard - ATX Manual de usuario

Asus

Asus Motherboard P5NT WS Manual de usuario

Asus

Asus M2N-X Manual de usuario

Asus

Asus TUF GAMING B460M-PLUS (WI-FI) Manual de usuario

Asus

Asus AT3IONT-I Series Manual de usuario

Asus

Asus M3N78-EMH HDMI - Motherboard - Micro ATX Manual de usuario

Asus

Asus ROG STRIX B650E-I GAMING WIFI Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

EPC

EPC EPC9147C Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario

Epson

Epson S5U13700P00C000 Manual de usuario

Gigabyte

Gigabyte GA-K8N Ultra-SLI Manual de usuario

Albatron

Albatron PX925XE Series Manual de usuario