Asus CUW-AM Manual de usuario

CUW-AM User’s Manual 1

1. FEATURES

Specifications

1. FEATURES

1.1 The CUW-AM

The CUW-AM motherboard is carefully designed for the demanding PC user who

wants advanced features processed by the fastest processors.

1.1.1 Specifications

•Latest Intel Socket 370 Processor Support

Intel Pentium

III 100MHz FSB Coppermine core FC-PGA

Intel Celeron™ 66MHz FSB Mendocino core PPGA

•Latest Intel 810 Chipset! The 810 (GMCH+ICH) supports 66/100MHz FSB

and UltraDMA/66.

•IntegratedGraphics!Controller supports 3D hyper pipelined architecture, par-

allel data processing and compression, precise pixel interpolation, full 2D hard-

ware acceleration, and motion video acceleration.

•Custom Graphics Driver! You can gain about 12% performance over that of

the standard graphics driver (2D highend graphics WinMark) using the custom

graphics driver. The custom graphics driver also provides more features and

provides selection of higher refresh rates and resolutions.

•Versatile Memory Support! DRAM controller supports asymmetrical address-

ing and two DIMM sockets support Intel PC100-compliant SDRAMs (16, 32,

64, 128, or 256MB) up to 512MB. (supports a maximum of 4 sides)

• Latest Low Pin Count Multi-I/O: Provides two high-speed UART compatible

serial ports and one parallel port with EPP and ECP capabilities.

• Integrated IDE! Controller supports UltraDMA/66 up to 66MB/s, UltraDMA/

33 up to 33MB/s, and PIO Mode 4 up to 17MB/s.

•Firmware Hub! Provides security and other latest power computing features.

•Enhanced ACPI & Anti-Boot Virus Protection! Programmable BIOS (Flash

EEPROM),offering enhancedACPIforWindows98compatibility,built-infirm-

ware-based virus protection, and autodetection of most devices for virtually au-

tomatic setup.

•Highest Audio Quality! AC’97 DAC/ADC (software audio) built into the au-

dio codec reduces noise to improve audio quality and performance for a SNR

(signal to noise ratio) of +90dB. These features greatly improve voice synthesis

and recognition. If more quality is required, an optional onboard Crystal PCI

audio improves audio quality beyond software audio.

E546

2CUW-AM User’s Manual

Specifications

1. FEATURES

1.1.2 Performance

•UltraPerformance! Onboard IDE Bus Master controller with two connectors

that support four IDE devices in two channels. Supports UltraDMA/66,

UltraDMA/33 (IDE DMA Mode 2), PIO Modes 3 & 4, and supports Enhanced

IDE devices, such as Tape Backup, CD-ROM, CD-R/RW, and LS-120 drives.

• Dual Speeds! CPU frequency can operate at either 66MHz or 100MHz while

system memory operates at 100MHz. This asynchronous design can optimize the

VGA performance under shared memory configuration.

• DoubleorQuadrupletheIDETransferSpeed!IDEtransfers using UltraDMA/

33 Bus Master IDE can handle rates up to 33MB/s and up to 66MB/s using

UltraDMA/66 technology. The best of all is that these new technology is com-

patible with existing ATA-2 IDE specifications so there is no need to upgrade

current IDE devices or cables.

•Concurrent PCI! Concurrent PCI allows multiple PCI transfers from PCI mas-

ter buses to memory to CPU.

• SDRAM Optimized Performance! ASUS smart series motherboards support

the new generation memory, Synchronous Dynamic Random Access Memory

(SDRAM), which increases the data transfer rate to 800MB/s max using PC100

SDRAM.

• ACPIReady!ACPI provides more Energy Saving Features for future operating

systems (OS) supporting OS Direct Power Management (OSPM) functionality.

With these features implemented in the OS, PCs can be ready around the clock,

yet satisfy all the energy saving standards. To fully utilize the benefits of ACPI,

an ACPI-supported OS such as Windows 98 must be used.

•Extreme Graphics! The integrated motion compensation allows for smooth

MPEG1 or MPEG2 video playback. Fast 3D graphics engine allows for an ex-

citing gameplay experience.

CUW-AM User’s Manual 3

1. FEATURES

Specifications

1. FEATURES

1.1.3 Intelligence

• Auto Fan Off: The system fans will power off automatically even in standby

mode. This function reduces both energy consumption and system noise, and is

an important feature in implementing silent PC systems.

• Dual Function Power Button: Pushing the power button for less than 4 sec-

onds when the system is in the working state places the system into one of two

states: sleep mode or soft-off mode, depending on the BIOS or OS setting. When

the power button is pressed for more than 4 seconds, the system enters the soft-

off mode regardless of the BIOS setting.

4CUW-AM User’s Manual

2. HARDWARE SETUP

2.1 CUW-AM Motherboard Layout

Motherboard Layout

2. H/W SETUP

SECONDARY IDEPRIMARY IDE

PANEL

WOL_CON

FLOPPY

DIMM Socket 2 (64/72-bit, 168-pin module)

DIMM Socket 1 (64/72-bit, 168-pin module)

Row

COM1

PARALLEL PORT

VGA

PS2KBMS

T: Mouse

B: Keyboard

PS_FAN

Intel 810

Graphics &

Memory

Controller

Hub (GMCH)

LCDTV

Intel I/O

Controller

Hub (ICH)

CUW-AM

PCI Slot 2

PCI Slot 1

PCI Slot 3

CR2032 3V

Lithium Cell

CMOS Power

ATXPWR

4Mbit

Firmware

Hub

(FWH)

GAME_AUDIO

Mic

Line

Out

Line

USB

T: Port 1

B: Port 2

SYS_FAN

CD_IN

COM2

AUX_IN

Audio

Codec

USBV1

Socket 370

Power

Controller

Clock

Generator

Super

I/O

CUW-AM User’s Manual 5

2. HARDWARE SETUP

Layout Contents

2. H/W SETUP

2.2 Layout Contents

Expansion Slots

1) DIMM1, DIMM2 p. 7 168-Pin DIMM Memory Support

2) Socket 370 p. 9 Central Processing Unit (CPU) Socket

3) PCI1, PCI2, PCI3 p.10 32-bit PCI Bus Expansion Slots

Connectors

1) PS2KBMS p.11 PS/2 Mouse Connector (6-pin female)

2) PS2KBMS p.11 PS/2 Keyboard Connector (6-pin female)

3) USB p.12 Universal Serial Bus Ports 1 & 2 (Two 4-pin female)

4) PRINTER p.12 Parallel Port Connector (25-pin female)

5) COM1 p.12 Serial Port COM1 Connector (9-pin male)

6) VGA p.13 Monitor (VGA) Output Connector (15-pin female)

7) GAME_AUDIO p.13 Game/MIDI Connector (15-pin female) (optional)

8) GAME_AUDIO p.13 Audio Port Connectors (Three 1/8”female) (optional)

9) PRIMARY/SECONDARYIDE p.14 Primary/Secondary IDE Connectors (Two 40-1pins)

10) FLOPPY p.14 Floppy Disk Drive Connector (34-1pins)

11) WOL_CON p.15 Wake-On-LAN Connector (3 pins)

12) COM2 p.15 Serial Port COM2 Header (10-1 pins)

13) CPU_FAN, PS_FAN p.16 CPU and Power Supply Fan Connectors (3 pins)

14) LCDTV p.16 TV Out Connector (Two 20-1 pins)

15) CD_IN, AUX_IN p.17 Internal Audio Connector (4-pins) (optional)

16) USBV1 p.17 USB Header (6-1 pins)

17) MLED (PANEL) p.18 System Message LED (2 pins)

18) KLOCK (PANEL) p.18 Keyboard Lock Switch Lead (2 pins)

19) EXSMI (PANEL) p.18 System Management Interrupt Switch Lead (2 pins)

20) SPEAKER (PANEL) p.18 System Warning Speaker Connector (4 pins)

21) PWR (PANEL) p.18 ATX Power / Soft-Off Switch Lead (2 pins)

22) HDLED (PANEL) p.18 IDE Activity LED (2 pins)

23) PLED (PANEL) p.19 System Power LED Lead (3-1 pins)

24) RESET (PANEL) p.19 Reset Switch Lead (2 pins)

25) ATXPWR p.20 ATX Power Supply Connector (20 pins)

6CUW-AM User’s Manual

2. HARDWARE SETUP

Motherboard Settings

2. H/W SETUP

2.3 Hardware Setup Procedure

Before using your computer, you must complete the following steps:

•Check Motherboard Settings

•Install Memory Modules

•Install the Central Processing Unit (CPU)

•Install Expansion Cards

•Connect Ribbon Cables, Panel Wires, and Power Supply

2.4 Motherboard Settings

WARNING! Computer motherboards and expansion cards contain very delicate

Integrated Circuit (IC) chips. To protect them against damage from static electric-

ity, you should follow some precautions whenever you work on your computer.

1. Unplug your computer when working on the inside.

2. Use a grounded wrist strap before handling computer components. If you do

nothave one, touch bothof your hands toa safely grounded objector to a metal

object, such as the power supply case.

3. Hold components by the edges and try not to touch the IC chips, leads or con-

nectors, or other components.

4. Placecomponents ona groundedantistatic pad or on the bag thatcame withthe

component whenever the components are separated from the system.

5. Ensure that the ATX power supply is switched off before you plug in or

remove the ATX power connector on the motherboard.

WARNING! Make sure that you unplug your power supply when adding or

removing system components. Failure to do so may cause severe damage to

your motherboard, peripherals, and/or components. The onboard LED when

lit acts as a reminder that the system is in suspend or soft-off mode and not

powered OFF.

CUW-AM User’s Manual 7

2. HARDWARE SETUP

System Memory

2. H/W SETUP

Install memory in any combination as follows:

Location 168-pin DIMM SDRAM Total Memory

DIMM1 Single-Sided/Double-Sided x1

(Rows 0&1) 16, 32, 64, 128MB, or 256MB

DIMM2 Single-Sided/Double-Sided x1

(Rows 2&3) 16, 32, 64, 128MB, or 256MB

Total System Memory (Max 512MB) =

2.5.1 General DIMM Notes

•ASUS motherboards support SPD (Serial Presence Detect) DIMMs. This is the

memory of choice for best performance vs. stability.

•SDRAM chips are generally thinner with higher pin density than EDO (Extended

Data Output) chips.

•Single-sided DIMMs come in 16, 32, 64,128MB; double-sided come in 32, 64,

128, 256MB.

2.5 System Memory (DIMM)

NOTE: No hardware or BIOS setup is required after adding or removing memory.

This motherboard uses only Dual Inline Memory Modules (DIMMs). Sockets are

available for 3.3Volt (power level) unbuffered Synchronous Dynamic Random Ac-

cess Memory (SDRAM) of 16, 32, 64, 128MB, or 256MB.

This chipset does not support ECC. However, ECC memory modules may still be

used, but the ECC function will not be available.

8CUW-AM User’s Manual

2. HARDWARE SETUP

2.5.2 DIMM Installation

Insert the module(s) as shown. Because the number of pins are different on either

side of the breaks, the module will only fit in the orientation shown. DIMM mod-

ules are longer and have different pin contact on each side and therefore have a

higher pin density. SIMMs have the same pin contact on both sides.

0 1

CUW-AM

CUW-AM 168-Pin DIMM Sockets

Lock

FRONT

20 Pins

60 Pins

88 Pins

TheDIMMs mustbe 3.3VUnbufferedforthis motherboard.To determinethe DIMM

type, check the notches on the DIMMs (see figure below).

168-Pin DIMM Notch Key Definitions (3.3V)

DRAM Key Position Voltage Key Position

Unbuffered

RFU

Buffered Reserved

3.3V

5.0V

The notches on the DIMM will shift between left, center, or right to identify the type

and also to prevent the wrong type from being inserted into the DIMM slot on the

motherboard.You must ask your retailer the correct DIMM type before purchasing.

This motherboard supports four clock signals per DIMM slot.

System Memory

2. H/W SETUP

CUW-AM User’s Manual 9

2. HARDWARE SETUP

CPU

2. H/W SETUP

2.6 Central Processing Unit (CPU)

The motherboard provides a ZIF Socket 370. The CPU that came with the mother-

board should have a fan attached to it to prevent overheating. If this is not the case,

then purchase a fan before you turn on your system.

WARNING!Be sure that there is sufficient air circulation across the processor’s

heatsink by regularly checking that your CPU fan is working.Without sufficient

circulation, the processor could overheat and damage both the processor and the

motherboard. You may install an auxiliary fan, if necessary.

To install a CPU, first turn off your system and remove its cover. Locate the ZIF

socket and open it by first pulling the lever sideways away from the socket then

upwards to a 90-degree angle. Insert the CPU with the correct orientation as shown.

The notched corner should point towards the end of the lever. Because the CPU has

a corner pin for two of the four corners, the CPU will only fit in the orientation as

shown. The picture is for reference only; you should have a CPU fan that covers the

face of the CPU. With the added weight of the CPU fan, no force is required to

insert the CPU. Once completely inserted, close the socket’s lever while holding

down the CPU.

CAUTION! Be careful not to scrape the motherboard when mounting a clamp-

style processor fan or else damage may occur to the motherboard.

0 1

CUW-AM

CUW-AM Socket 370

Socket 370 CPU

(Top) Socket 370 CPU

(Bottom)

Notch Celeron

Gold Arrow Coppermine

10 CUW-AM User’s Manual

2. HARDWARE SETUP

Expansion Cards

2. H/W SETUP

2.7 Expansion Cards

WARNING! Make sure that you unplug your power supply when adding or

removing expansion cards or other system components. Failure to do so may

cause severe damage to both your motherboard and expansion cards.

2.7.1 Expansion Card Installation Procedure

1. Read the documentation for your expansion card and make any necessary hard-

ware or software settings for your expansion card, such as jumpers or switches.

2. Remove your computer system’s cover and the bracket plate with screw on the

slot you intend to use. Keep the bracket for possible future use.

3. Carefully align the card’s connectors and press firmly.

4. Secure the card on the slot with the screw you removed above.

5. Replace the computer system’s cover.

6. Set up the BIOS if necessary.

7. Install the necessary software drivers for your expansion card.

Tabla de contenidos

Otros manuales de Placa madre de Asus

Asus

Asus P5E3 DELUXE Manual de usuario

Asus

Asus ROG STRIX Z390-E GAMING Manual de usuario

Asus

Asus P4SGL-VM Manual de usuario

Asus

Asus H81M-CS Manual de usuario

Asus

Asus M2N-VM DVI Manual de usuario

Asus

Asus A7V8X-X Manual de usuario

Asus

Asus Motherboard A7N8X-VM Guía de inicio rápido

Asus

Asus P7H55 series Manual de usuario

Asus

Asus C785S-IM-AA Manual de usuario

Asus

Asus AW171 Manual de usuario

Asus

Asus C8HM70-I Series Guía de inicio rápido

Asus

Asus P5BV/SAS Manual de usuario

Asus

Asus P4SGL-VM Manual de usuario

Asus

Asus P5N32-SLI SE DELUXE Manual de usuario

Asus

Asus P5WDG2 WS Professional Manual de usuario

Asus

Asus CUSL2-M Manual de usuario

Asus

Asus MAXIMUS VII IMPACT Manual de usuario

Asus

Asus P65UP5-PKND Manual de usuario

Asus

Asus Prime H510M-A Manual de usuario

Asus

Asus TUF Z390-PLUS GAMING Manual de usuario

Asus

Asus H97M-PLUS Manual de usuario

Asus

Asus DSBF-DE - Motherboard - SSI EEB 3.61 Manual de usuario

Asus

Asus M5A78L-M LE/USB3 Manual de usuario

Asus

Asus H61M-G Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

EPC

EPC EPC9147C Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario

Epson

Epson S5U13700P00C000 Manual de usuario

Gigabyte

Gigabyte GA-K8N Ultra-SLI Manual de usuario

Albatron

Albatron PX925XE Series Manual de usuario