Astro Tool 620667 Manual de usuario

1 9-19-14 TI667-14-0

ASTRO TOOL CORP.

CONNECTOR ASSEMBLY TOOLING

HOW TO USE THE LARGE DEDICATED CRIMP TOOL

Catalog Number 620667

GENERAL

The 620667 is a cycle controlled hand crimping tool.

It is a fast, versatile, manually operated, octadent tool for

crimping circular pin and socket contacts.

This tool is configured for one specific wire size and

is set to .071”at the factory and locked in place. The

620667 also includes a locator that is permanently

attached. No operator adjustments are required.

For long life and optimum performance, this tool

should be kept clean and handled carefully, as any other

precision instrument.

OPERATION

Open and close the tool several times and observe the

precision cycle control ratchet mechanism. Note that the

tool may not be opened or closed without completing the

cycle.

TOOL GAGING

It will be necessary to verify the opening by using a

gage pin assembly. Gage, 620667-G, is available to

properly gage this hand tool. Close the tool completely

and insert the GO end of the gage assembly between the

indenters, as shown in figure #1.

Indenter

Gage Pin

Figure #1

The GO pin should slide freely between the indenter

tips.

Close the tool down completely and insert the NO

GO end of the gage assembly into the indenter opening

as shown in figure #1.

The NO GO pin must NOT go between the indenter

tips.

CAUTION:

DO NOT CRIMP GAGE

TOOL DAMAGE WILL RESULT.

2 9-11-03 TI548-93-2

TOOL SERVICE

Astro Tool's 620667 Crimp Tool is designed for long,

reliable service. If the tool becomes inoperative or does

not gage properly, it is suggested that you contact our

Customer Service Department for a Return Goods

Authorization number and return the tool to our factory.

Upon receipt of the tool, Astro will inspect and

overhaul each tool to put the tool back into acceptable

and efficient operating condition. Worn parts will be

replaced or repaired.

Service charges for tools not under warranty will be

advised upon request.

Parts that Astro deems to have been damaged due to

neglect, misuse or accident; and parts that have been

altered or repaired by persons other than Astro Tool

Corp. employees will be replaced subject to additional

charge for such parts.

ASTRO TOOL CORP. MANUFACTURERS OF INSERTION, REMOVAL,

CRIMP TOOLS AND CONNECTOR SERVICE KITS

ASTRO TOOL CORPORATION 21615 S.W. T-V HWY. BEAVERTON OREGON 97003

503-642-9853 FAX 503-591-7766

Tabla de contenidos

Otros manuales de Herramientas de crimpado de Astro Tool

Astro Tool

Astro Tool AMT4001 Manual de usuario

Astro Tool

Astro Tool 612596 Manual de usuario

Astro Tool

Astro Tool 613214 Manual de usuario

Astro Tool

Astro Tool TGV101 Manual de usuario

Astro Tool

Astro Tool MS 3191-4 Manual de usuario

Astro Tool

Astro Tool 615708 Manual de usuario

Astro Tool

Astro Tool 612648 Manual de usuario

Astro Tool

Astro Tool 620667 Instrucciones de funcionamiento

Astro Tool

Astro Tool 615717 Manual de usuario

Astro Tool

Astro Tool 616336 Manual de usuario

Manuales populares de Herramientas de crimpado de otras marcas

Panduit

Panduit CT-1000 Guía del administrador

JST

JST CS 10 Manual de usuario

molex

molex 63811-5100 Manual de usuario

Danfoss

Danfoss ET4200 Manual de usuario

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manual de usuario

TE Connectivity

TE Connectivity 2063528-1 Manual de usuario

molex

molex 63825-3000 Manual de usuario

Tyco Electronics

Tyco Electronics 69156-1 Manual de usuario

CRH

CRH CRL CBLHCT1 Manual de usuario

Emerson

Emerson Klauke ES 105CFM Manual de usuario

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Manual de instrucciones

Danfoss

Danfoss ET4350 Manual de usuario

Milwaukee

Milwaukee M18 Manual de usuario

HOGERT

HOGERT HT1P169 Manual de usuario

Textron

Textron ESG105L Manual de usuario

Tyco Electronics

Tyco Electronics 90035-3 Manual de usuario

Emerson

Emerson Klauke ES 20RMCCFB Manual de usuario

Continental Refrigerator

Continental Refrigerator PC150HD Manual de usuario