Astral Pool RAMSES Manual de usuario



INSTRUCTION MANUAL



In-

GroundHousing



IMPORTANT:

The

instruction manual

that you are

holding in y

hands

contains important information

about the

safety measures

adopt

during installation,

start up and

maintenance.

Thus,

extremely important

that both the

installer

and the user read

instructions before beginning s



ATTENTION



Anyone working

on the

installation

must have the

required qualifications

for

this

Avoid contact with electrical

The

normativesin

force for

accident prevention

must be

IEC standards 3647702

must be

complied with: ELECTRICAL INSTALLATIONS

BUILDINGS. SPECIAL INSTALLATIONS. SWIMMING

Any

maintenance operation

or part

replacement

must be done

with

the

disconnected

from the

Do not

handle

the

equipment with

wet

This equipment CANNOT

CONNECTED

TO A

REGULAR

PLUG.

This

REQUIRES PROPER ELECTRICAL INSTALLATION. This

must be done by a

following all

the

normatives

electrical safety in

force

each

coun

The

supply

to the

unit

must

ALWAYS

PROTECTED

BY A

EARTHING CONNECTIONis

Use a

SECTION CABLE with

the

appropriate power

for the

unit

and for the

distance

the

control

pan

Use a

lock

padlock

so that

children

other unauthorised persons cannot access

interior

of the

ALWAYS

STOP THE

PUMP BEFORE CHANGING

THE

POSITION

OF THE

SELECTOR

Do not open the cover of the spa

whenit

may be

caught

by a

current

or gust of

The manufacturer is exempt

from

all liability

due to

improper assembly,

start

up or any

changes

incorporations

of any

non-authorised electrical

compon



For optimum performance of your in-ground housing unit, follow the instructions

below.

1.

GENERAL

INSTALLATION



3.1. Do the excavation in stages.



In-ground housing unit for a pool is made of injected-polymer reinforced with

fibreglass and a cover.

It houses a D550 Aster filter and a Sena 1CV circulation pump.



It is advisable to situate the equipment away from the pool, at least 3.5 m from

the edge. During installation, follow IEC international standard 60364-7-702 on

the Requirements for special installations or locations. Section 702: Swimming

pools and other basins.



3.2. Make a properly levelled concrete slab.



3.3. -Position the unit



3 4



3.4. Do the excavation to prepare for laying the intake and output tubes to the

pool and the electrical supply.

The intake and output tubes must rest on a bed of sand.

It is recommended that you make a drain in the back of the unit using the

knock-out to make the hole. This should be connected to the general tank with a

slight slope.



3.5.- Perforate the unit on the side where the electrical supply is to enter, with a

diameter that matches the cable to be installed. Determine the section of the

cable depending on power consumption and drops in voltage.

Install a cable gland of the appropriate size for the cable section at the entry.



4.

INSTALLATION

OF THE LEGS

THE



4.1. - This makes for more accurate levelling. The unit should be put in place

when the concrete floor begins to set and levelled by the upper part. The legs

should be drilled to insert rods so the unit is fully anchored to the concrete,

without the possibility of moving when pressure is applied to the sides.



The installation must include a highly sensitive 2 pole differential on the general

panel (conforming to RBT ITC-BT-017). The differential is not supplied with the

spa.



To avoid flooding, fill with dirt, forming a slight incline.



ELECTRICAL CONNECTION (ONLY FOR MODELS WITH ELECTRICAL CONTROL

BOX)

For your safety, place terminals that are appropriate to the section of the cables

on the ends of the cables to be connected. Use cable H07RNF.



ATTENTION – VERY



This equipment cannot be connected to a regular plug.

This equipment requires proper electrical installation. This must be done by

specialist, following all the normatives on electrical safety in force in each

country.

The supply to the unit must always be protected by a highly-sensitive

differential

An earthing connection is required.

Use a section cable with the appropriate power for the unit and for the

distance to the control panel



ELECTRICAL



Instakes from the

pool



•

Skimmer

•

Drain input

•

Suction

Drain output



7 8

Return to

pool



PHASE



urn o

the pump.

910



STARTING U

Position the selector valve to rinse and run the pump for about 15 seconds.

Stop the pump again and put the selector valve on filter.

8. Close the selector valve of the pool cleaner.

9. Connect the pump.



Note: Any changing of the position of the selector valve must be done with the

puma stopped. Otherwise, the filter or the installation could be damaged.



Replace the cover of the unit, affixing the rear part with the corresponding

screws.



1. Remove the cover of the unit to begin the start up. Unscrew the 6 screws that

affix the hinge to the cover- not those that affix the hinge to the unit- before

lifting it.



CONSULT

THE

MANUAL

FOR THE



2. Open the filter and fill it halfway with water. Protect the diffuser in the interior

of the filter so sand does not get into it.

3. Fill the filter with the appropriate quantity (indicated on the specifications

label, or up to 2/3 of the total filter height) of silex sand with a grain size of 0.4 -

0.8

4. Clean the remnants of silex from the mouth, cover and gasket housing, and

close the filter. For more information, please consult the manual for the filter.

If the unit is below the water level, you will only need to open the input and

output valves and the air vent until the filter and the pump are full of water.

5. Put the valves in the following positions:

-SKIMMER OPEN

-DRAIN INPUT OPEN

-POOL CLEANER OPEN

-RETURN OPEN

-SELECTOR VALVE CLEAN



6. Start up the pump and clean the filter.

Run the cleaning until you see that the water is clean and clear in the window on

the selector valve.



- IT IS

RECOMMENDED

THAT YOU USE A LOCK OR PADLOCK

THAT CHILDREN OR OTHER UNAUTHORISED PERSONS

CAN

ACCESS THE

INTERIOR

OF THE

UNI



PROGRAMMING THE FILTER. See instructions for the programmer in the interior

of the control panel.

ONLY FOR MODELS WITH AN ELECTRICAL CONTROL PANEL

11 12



5. USER´S



5.3.-

After CLEANING the filter and before returning the equipment to filtration, it is

advisable to run a RINSE to prevent the first quantity of water that is still cloudy

from going directly into the pool. To do this, with the pump stopped, put the

selector valve on RINSE. Start up the pump and run it for about a minute.

Always check the window of the selector valve to ensure that this is the correct

time, since it depends on the amount of filth accumulated in the filter.

ALWAYS STOP THE PUMP BEFORE CHANGING THE POSITION OF

SELECTOR



5.1.-



With the pump stopped, put the selector valve handle on FILTER.

Start up the pump.

Periodically check the manometer during operation, which will indicate the

degree of saturation of the filter.



5.2.-



The solid particles in the pool that are collected by the input drain and the

skimmers remain in the sand in the filter, which constantly decreases the water

flow. Due to this, the pressure increases progressively. When the pressure

reaches 1.3 kg/cm

, a CLEANING will be done (this is an approximation; it

depends on the distance between the unit and the pool, its location,

etc.).

Proceed

as follows:

Put the selector valve on the CLEAN position and start the pump. Run this for 2

minutes. Always check the window of the selector valve to ensure that this is the

correct time, since it depends on the amount of filth accumulated in the filter.



5.4.-



When you put the selector valve in this position, the water from the pump will

circulate directly to the pool without passing through the filter.



5.5.-



If the pool does not have a drain in the bottom, it can be emptied using the filter

pump by putting the valve on DRAIN. To do this, open the valves of the input

drain and close those of the skimmers and pool cleaner.



5.6.-



This position blocks water entry into the filter



All

of our

products

come

with

a TWO YEAR

warranty

from the date

delivery.

Our

warranty includes in-factory repair

and

replacement

the

after-sale service

defective pieces.

The parts

replaced

repaired

under

this warranty will

not

extend

the

warranty

original product,

but they

will

have

their

own



For the

warranty

to be

valid,

the buyer must have proof of the date

sale

and

reception

of the



For the

warranty

to be

valid,

the buyer must

strictly follow

manufacturer’s instructions included in

the

documentation

that

with

the

product, whenever applicable according

to the range

model

of the

product.

warranty covers normal

wear and tear due

use of the

As for the parts,

components

disposable materials, it will

out

the

documentation

that comes

with

the

product,

app



The

warranty

does not cover the

following:

1. The

product

has

misused;

2. The

product

has been

repaired

handled

unauthorised person;

3. The

product

has been

repaired

with non-original

parts, or 4. The

product

has been

installed

or set

Except where prohibited

legislation,

the

shipping

and

return

costs

defective materials shall

paid

by the buyer. The

present

does not

limit

infringe

upon the

rights

that

correspond

covered

imperative national

METALAST,S.A.U

Passeig de Sanllehy,25

08213 Polinyà, Spain

Tel. +34 93 713 18 55

Fax. +34 93 713 41 11



RESERVE

THE

RIGHT

CHANGE

THE

SPECIFICATIONS,

ALL OR

PART, OF OUR

PRODUCTS

OR THE

CONTENT

THIS

WITHOUTPRIOR

Tabla de contenidos

Otros manuales de Equipo de iluminación de Astral Pool

Astral Pool

Astral Pool SKIMMER Manual

Astral Pool

Astral Pool Net 'N' Clean 22514 Manual

Astral Pool

Astral Pool KEOPS Manual de usuario

Astral Pool

Astral Pool KEOPS Manual de usuario

Astral Pool

Astral Pool Eco Manual de usuario

Astral Pool

Astral Pool TRAMONTANE Manual de usuario

Astral Pool

Astral Pool DECKWELL Manual de instrucciones

Astral Pool

Astral Pool LumiPlus 59813 Manual

Astral Pool

Astral Pool Smart+ 60 Manual

Astral Pool

Astral Pool 00349 Manual

Astral Pool

Astral Pool Mini Skimmer Manual

Astral Pool

Astral Pool PC95 Manual de usuario

Astral Pool

Astral Pool LUMIPLUS FLEXIMINI Manual de usuario

Astral Pool

Astral Pool 00250 Manual

Astral Pool

Astral Pool Energy Sel Series Manual de usuario

Astral Pool

Astral Pool Glassy L Manual del propietario

Astral Pool

Astral Pool Viron Connect 10 Manual de usuario

Astral Pool

Astral Pool Heliox UV MP 50 Manual

Astral Pool

Astral Pool 42350 Manual

Astral Pool

Astral Pool 00251 Manual

Astral Pool

Astral Pool Waterlift Manual de usuario

Astral Pool

Astral Pool DeckWell 330 Manual de usuario

Astral Pool

Astral Pool Starlight Hoop Manual de usuario

Astral Pool

Astral Pool 01413 Manual

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario