Assa Abloy Corbin Russwin DC3200 Series Manual de usuario

80-9330-3004-152 04/18

Installation Instructions

permission of Corbin Russwin, Inc. is prohibited.

DC3200 Series

Important

• An improperly installed or incorrectly adjusted door closer may cause property damage or personal injury; and will void

product warranty.

• To avoid personal injury, DO NOT DISASSEMBLE THIS DOOR CLOSER BODY.

• Door closers must be securely fastened to a properly reinforced door and frame with fasteners provided.

• Door closers with a HOLD OPEN ARM are not permitted to be installed in ﬁre door assemblies.

• Door and frame must be speciﬁcally templated for 85°, 90°, 95°, 100°, 105° orb 110° door swing.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

A10 Heavy Duty Non-Hold Open Regular Arm

80-9330-3004-152 04/18

DC3200 Series Closer

Installation Instructions

A10 Heavy Duty Non-Hold Open Regular Arm

permission of Corbin Russwin, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

**NOTE: These forces are for standard templating with bearing type

hinges and do not account for pressure differentials and draft.

Size of Door & Door Closer

Type of

Installation Interior Exterior

In-swinging

Recommended

Closer Size

**Max. Opening

Force lbs/f

Regular Arm

2' 4" - 1 8

3' 0" - 2 14

3' 6" 2' 6" 3 16

4' 0" 3' 0" 4 22

4' 6" 3' 6" 5 24

5' 0" 4' 0" 6 26

TO DETERMINE

HAND OF

YOUR DOOR:

LEFT

HAND

DOOR

RIGHT

HAND

DOOR

RHR LHR

1 Introduction

3/8

(10)

1/4-20 THREAD

Drill thru 9/32 (7.1) Enlarge to

3/8

(9.5) Dia. This Side Only

(4 Places)

DOOR

THICKNESS

SEX NUT

LENGTH “L”

1-3/8" (35mm)

1--3/4" (44mm)

&OVER

1-9/32" (33mm)

1-21/32" (42mm)

MOUNTINGSCREW SPECIFICATIONS

ARM AND CLOSER BRACKET

}

or{Option M54:

Sex nuts, furnished

when ordered

1/4-20 oval head machine

screw or 1/4-14 self-drilling

screw Type BSD. 3/16 (4.8)

diameter pilot hole required

forWood Applications.

3/8

(10)

1/4-20 THREAD

Drill thru 9/32 (7.1) Enlarge to

3/8 (9.5) Dia. This Side Only

(4 Places)

DOOR

THICKNESS

SEX NUT

LENGTH “L”

1-3/8" (35mm)

1--3/4" (44mm)

&OVER

1-9/32" (33mm)

1-21/32" (42mm)

MOUNTINGSCREW SPECIFICATIONS

ARM AND CLOSER BRACKET

}

or{Option M54:

Sex nuts,

furnished

when ordered

1/4-20 oval head machine

screw or 1/4-14 self-drilling

screw Type BSD. 3/16 (4.8)

diameter pilot hole required

forWood Applications.

Figure 1

BEFORE INSTALLING:

• The Americans with Disabilities Act (ADA) requires that doors having door closers have an opening force not to

exceed 5 lbf. for interior doors, 8.5 lbf exterior doors.

• The door closer’s power size adjustment feature may require adjustment to its lowest setting to comply with ADA

opening force guidelines.

• ADA compliant closer: DC3200.

80-9330-3004-152 04/18

DC3200 Series Closer

A10 Heavy Duty Non-Hold Open Regular Arm

Installation Instructions

permission of Corbin Russwin, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

2 Installation

1. Template

Mark and prepare door and jamb (for closer

bracket and arm bracket).

For Vertical Dimensions use “Mounting

Dimensions Chart” (Figure 2)

NOTES:

• Check hand of door. (Figure 1)

• Right Hand Application Shown,

Left Hand Opposite

• Dimensions given in inches (mm).

Do Not Scale Drawing.

• Closer must be installed in a true

horizontal plane to ensure proper closer

performance.

• Door opening (up to 180°) is dependent

upon door, frame, wall and hinge/pivot

conditions permitting.

• Maximum Hinge Side Reveal 1/8" (3mm).

Figure 2

CLOSER BRA

CKET

2-1/4

(57.2)

*10-1/4

(260)

*6-1/4

(159)

FRAME LINE

TOPOF DOOR

LHINGE OR PIVOT

ARM BRACKET

4-5/16

(109.5)

(25.4)

* To obtain extra closing force add 3" (77mm) to dimensions marked. This

will limit degree of door opening to 110° and void compliance with ADA

opening force guidelines.

MOUNTING DIMENSIONS MINIMUM

CLEARANCE

REQUIRED

OVER DOOR

TOP RAIL DIM. A DIM. B

2-1/2" (64mm)

& OVER

(25.4mm)

3/4"

(19mm)

1-11/16"

(43mm)

1-3/4" (44mm)

-MIN.

5/8"

(16mm)

1-1/8"

(29mm)

2-1/16"

(53mm)

80-9330-3004-152 04/18

DC3200 Series Closer

Installation Instructions

A10 Heavy Duty Non-Hold Open Regular Arm

permission of Corbin Russwin, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

2 Installation

2. Install Closer Bracket. (Figure 3)

Figure 3

Figure 4

MAIN ARM

Pin Hole

End

Countersunk

Holes

NOTE ARMS WILL

FORM A “V” POSITION

Rotate

approximately

5°

1/4-20 x 1/2 OHMS (2)

Pins

(2)

3. Mount Closer Body to Closer Bracket.

(Figure 4)

1/4-14 x 1-1/2

OH Self-Drilling (4)

1/4-20 x 3/4 OHMS w/Sex

Nuts (4) (M54 Option)

MAIN ARM

Pin Hole

End

Countersunk

Holes

NOTE ARMS WILL

FORM A “V” POSITION

Rotate

approximately

5°

1/4-20 x 1/2 OHMS (2)

Pins

(2)

80-9330-3004-152 04/18

DC3200 Series Closer

A10 Heavy Duty Non-Hold Open Regular Arm

Installation Instructions

permission of Corbin Russwin, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

2 Installation

MAIN ARM

Pin Hole

End

Countersunk

Holes

NOTE ARMS WILL

FORM A “V” POSITION

Rotate

approximately

5°

1/4-20 x 1/2 OHMS (2)

Pins

(2)

4. Position Arm on Closer. (Figure 5)

Main arm projects straight out at 90° angle to

door.

5. Preload and Fasten Arm to Frame.

(Figure 6)

Close door, swing arms to align holes in arm

bracket with pre-drilled holes on frame and

install attaching screw.

NOTE: Arms will form a “V” position.

Extended Maintenance

Lubricate Arm periodically at shaded points

with a drop or two of appropriate lubricant.

Figure 5

Figure 6

MAIN ARM

Pin Hole

End

Countersunk

Holes

TE ARMS WILL

FORM A

“V” POSITION

Rotate

approximately

5°

1/4-20 x 1/2 OHMS (2)

Pins

(2)

1/4-14 x 1-1/2

OH Self-Drilling

(2)

80-9330-3004-152 04/18

DC3200 Series Closer

Installation Instructions

A10 Heavy Duty Non-Hold Open Regular Arm

permission of Corbin Russwin, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

3 Adjustments

Adjustments (Figure 7)

(3/32 Allen Wrench Provided)

Closing Speed Valve (Figure 8)

To adjust speed of door closing from fully

open to a position 2 to 5" from closed, turn

Closing Speed Valve CLOCKWISE to SLOW

closing, COUNTER-CLOCKWISE to SPEED

closing.

Latching Speed Valve (Figure 9)

After closing speed has been obtained, turn

latching speed valve CLOCKWISE to SLOW

latching or COUNTER-CLOCKWISE to SPEED

latching for last 2" to 5" of door travel.

NOTE: Set combination of CLOSING and

LATCHING speeds to between 3 and 7

seconds. Use of door by handicapped,

elderly or small children, may require

even greater closing time.

Backcheck Intensity Valve (Figure 8)

Turn valve COUNTER- CLOCKWISE to reduce

backcheck or CLOCKWISE to increase

backcheck. (Backcheck should be set to give

a soft cushioning action, not a sudden stop).

Delayed Action Valve (Figure 8)

Turn valve CLOCKWISE to SLOW closing,

COUNTER-CLOCKWISE to SPEED closing.

Delayed action may be adjusted from 20

seconds to 90 seconds, depending on degree

of door swing. Delay occurs at the beginning

of the door closing cycle from fully open down

to 70°, where the closing speed valve then

begins its control.

Delayed Action

Option

M-71

Backcheck

Latch

Sweep

LATCHING

SPEED

VA LV E

Power

Size

Stamp

Date Stamp

BACKCHECK

INTENSITY VALVE

OPTION M71

DELAYED

ACTION VALVE

CLOSING

SPEED VALVE

SPRING POWER ADJUSTER

(5/16" WRENCH or SOCKET)

(FLAT TIP SCREWDRIVER)

Figure 7

Figure 8

Figure 9

80-9330-3004-152 04/18

DC3200 Series Closer

A10 Heavy Duty Non-Hold Open Regular Arm

Installation Instructions

permission of Corbin Russwin, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

3 Adjustments

Adjust Spring Power According to Chart

DC3200 Size 1-6 Adjustment (Figure 10)

• All DC3200 closers are factory set at an

approximate Size 3.

Full Cover(Standard)

Slim Cover (Option M76)

Figure 10

Figure 11

Size of Door No. of Full (360°)

Turns Clockwise of

Power Adjuster

Equivalent Closer

Size (Approx.)

Interior Exterior

In-Swinging

2' 4"

(712)

2' 6"

(764) 4 2

2' 6"

(764)

3' 0"

(915) 8 3

3' 0"

(915)

3' 6"

(1067) 12 4

3' 6"

(1067)

4' 0"

(1219) 16 5

Figure 12

4 Cover Installation

Full Cover(Standard)

Slim Cover (Option M76)

Install Cover (Figure 11)

Slip cover over closer. Hold tightly against

closer mounting surface. Secure on each

side with 6-32 x 1/4 PBHMS screws.

Slim Cover Option M76 only (Figure 12)

Position spindle cap over unused spindle

and secure with truss head screw.

• Adjust closer as necessary for door size

using this chart.

• Readjustment may be required to suit

prevailing conditions.

80-9330-3004-152 04/18

permission of Corbin Russwin, Inc. is prohibited.

Patent pending and/or patent: www.assaabloydss.com/patents

Corbin Russwin

225 Episcopal Road

Berlin, CT 06037

Phone: 800-543-3658

Fax: 800-447-6714

corbinrusswin.com

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

Tabla de contenidos

Otros manuales de Sistema de apertura de puertas de Assa Abloy

Assa Abloy

Assa Abloy RD150-3 Manual de usuario

Assa Abloy

Assa Abloy DC130 Manual de usuario

Assa Abloy

Assa Abloy Yale 6000 Series Manual de usuario

Assa Abloy

Assa Abloy Norton LEO 5700 Series Guía rápida

Assa Abloy

Assa Abloy Besam SW300 Manual de usuario

Assa Abloy

Assa Abloy SW100 Manual de usuario

Assa Abloy

Assa Abloy DC700 Manual de usuario

Assa Abloy

Assa Abloy DC 700G-FT BGS Manual de usuario

Assa Abloy

Assa Abloy 5800 ADAEZ PRO Manual de usuario

Assa Abloy

Assa Abloy 332 Series Manual de usuario

Assa Abloy

Assa Abloy Besam SW300 Manual de usuario

Assa Abloy

Assa Abloy Norton 7970DPS-B Series Manual de usuario

Assa Abloy

Assa Abloy NORTON RIXSON 1600 Series Manual de usuario

Assa Abloy

Assa Abloy CMD Manual de usuario

Assa Abloy

Assa Abloy SARGENT FIREGUARD 12-2468 Manual de usuario

Assa Abloy

Assa Abloy Corbin Russwin ED4000 Series Manual de usuario

Assa Abloy

Assa Abloy RIXSON SMOK-CHEK V 0101 Manual de usuario

Assa Abloy

Assa Abloy Corbin Russwin PED5800 Series Manual de usuario

Assa Abloy

Assa Abloy Corbin Russwin PED4600 A Series Manual de usuario

Assa Abloy

Assa Abloy Pando Mini Go Manual de usuario

Assa Abloy

Assa Abloy Besam SW200i US Manual

Assa Abloy

Assa Abloy Besam SL500 Manual de usuario

Assa Abloy

Assa Abloy UNION DoorSense 8755A Manual de usuario

Assa Abloy

Assa Abloy Norton 6300 Series Manual de instalación

Manuales populares de Sistema de apertura de puertas de otras marcas

Pamex

Pamex KT-INP35 Manual de usuario

Label

Label NEPTIS/LE Manual de usuario

Cal-Royal

Cal-Royal N-F77CVR Manual de usuario

Scrigno

Scrigno OPEN1000 Manual de usuario

TriMark

TriMark UM 34 Manual de usuario

BFT

BFT WIND RMB 130B 200 Manual de usuario

Alecto

Alecto ADI-250 Manual de usuario

Besam

Besam Swingmaster MP Guía

CRL

CRL SENIOR PRIMA Manual de usuario

GAL

GAL MOVFR Hoja de especificaciones

Olide

Olide 120B Manual de usuario

Normstahl

Normstahl IDO7 Manual de usuario

Häfele

Häfele Finetta T 70 VF Manual de usuario

AGS

AGS D-PL Manual

Stanley

Stanley MA900ñ Instrucciones de instalación

WITTUR

WITTUR Hydra Plus UD300 Manual

Alutech

Alutech TR-3019-230E-ICU Instrucciones de instalación y funcionamiento

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Hoja de especificaciones