Assa Abloy Adams Rite 3000SE Manual de usuario

3000SE/8000SE Exit Devices

Motorized Latch Retraction

Installation Instructions

80-0180-140, Revision C

TABLE OF CONTENTS

Preparing for Installation...........................................................4

Function .........................................................................4

Specifications................................................................4

Mounting Information ...................................................4

Safety Instructions........................................................4

Installation Requirements .........................................................6

Installing......................................................................................7

Calibrating...................................................................................8

Troubleshooting.........................................................................9

Preparing for Installation

Function

The SE feature is available on all 3000/8000 series exit devices

and provides for latch retraction of the device from a remote

location. The exit device is Fail Secure—in the event of a power

failure, the exit device defaults to a latched condition. The linear

actuator is rated for both continuous and intermittent operation.

Specifications

Rated Voltage: 24 VDC

Rated Current: 0.4 Amperes (S) to retract; 0.2A to hold

(

Nominal)

0.45A to retract; 0.25A to hold (Maximum)

Rated for continuous duty

Mounting Information

The exit device is mounted in the standard manner per the

specific exit device installation instructions. The exit device must

function mechanically prior to operating electrically.

CAUTION: This product must be installed in accordance

with all applicable building and life safety

codes.

Safety Instructions

This device is limited in its applications, and should only interface

with components that are equally rated. Any failure to observe

and adhere to the operating limits may cause permanent

damage.

CAUTION: Failure to ensure that there are no shorts

across power feed lines may result in damage

to power transfer and electric retraction of the

exit device.

Figure 1. Adams Rite Model # PS-SE Power Supply

Figure 2. Wire Sizing

Installation Requirements

The following are the installation requirements/comments for the

SE feature exit device:

NOTE 1: Recommended circuit hookup for the Adams Rite

power supply is provided in Figure 1, “Adams Rite

Model # PS-SE Power Supply,” and the owner’s

manual supplied with the power supply.

NOTE 2: Wire size recommendations are provided in Figure 2,

“Wire Sizing.”

•24 VDC device power is supplied by an Adams Rite power

supply (Part Number: PS-SE).

•A remote switch or normally open dry contacts within the

access control system is required to control the electrical

operation.

•Switch contacts are rated for the power requirements shown

in Figure 1.

NOTE: The power supply owner’s manual provides

instructions on how to set the solenoid hold time.

•Operation of the switch will retract the latching mechanism for

as long as the switch closure is maintained, or until the

adjustable delay times out.

•A maximum of two electrified devices, activated either

sequentially or independently, can be operated with one

PS-SE power supply.

•There is an option to install a battery backup in the PS-SE

power supply by ordering the BBK-SE battery backup system

kit and two 12-volt, 7-ampere-hour batteries. Installation is

per the PS-SE owner’s manual.

CAUTION: This product must be installed in accordance

with all applicable building and life safety

codes.

Installing

NOTE: The exit device template should be reviewed to

determine applicable bar height for installation.

1. INSTALL the exit device with SE feature in accordance with

the specific exit device installation instruction.

2. DRILL a 3/8” (0.375“ or 9.53 mm) on the door for wiring

access at the time of installation (see Figure 3, “Door

Preparation”).

Figure 3. Door Preparation

3. PASS the wiring, using an Adams Rite 4612 wire transfer or

equivalent to properly transfer the wires from the frame to the

door.

4. ENSURE wires are protected from abrasion where they pass

through the hole in the door by using a sufficient protection

device [i.e., rubber grommet (not supplied)].

NOTE 1:Proper calibration needs to occur on all SE exit devices

when installed prior to initial power up.

NOTE 2:Labels are affixed to all SE exit devices to detail

calibration steps, and also provide a Quick Response

(QR) code that is a link to a calibration instruction video.

Calibrating

NOTE: Verification of the PCBA type ensures that the correct

one is installed when there is an issue that could be

PCBA related.

1. PERFORM a visual verification to identify whether the PCBA

installed is the older (four-capacitor) or newer (two-capacitor).

2. PERFORM the calibration process for the installed exit

device.

[a] ENSURE power is disconnected.

[b] IF PCBA is being replaced,

THEN INSTALL new PCBA.

[c] DEPRESS the push bar fully.

[d] APPLY 24 VDC power to the exit device.

[e] CONTINUE to hold the push bar until an audible

activation sound is heard from the motor, and then

RELEASE the push bar to its latched position.

NOTE: The push bar will automatically complete the

calibration process.

[f] IF the calibration process does not complete

successfully,

THEN REPEAT Steps [a] – [e].

Troubleshooting

No power to the exit device

1. ENSURE that the power connector is connected properly, all

wiring from the power supply is continuous (without opens),

and there are no shorts to ground.

Neither exit device retracts after the control switch is

activated

1. VERIFY connections.

2. ENSURE exit device wires are properly terminated in the

power supply.

3. VERIFY continuity through power transfer devices such as

wired hinges and door cords/loops.

“Main Power” LED is not lighted

1. ENSURE line voltage is present.

2. CHECK fuse F2 (in the black fuse holder).

3. ENSURE that the primary voltage selection switch SW2 is

properly set.

“Output Power” LED on power supply board is not lighted

NOTE: If fuse F1 is blown, the wires that run to the exit

device are probably shorted together against the

conduit, door frame, or electric hinge. A meter should

be used to check for shorts.

1. CHECK fuse F1.

2. ENSURE that a fire alarm is connected between J3-9 and J3-

10, or the factory installed jumper between J3-9 and J3-10 is

removed.

IN1 and IN2 lights do not light in response to input switches

1. CHECK to see if there is an open connection in the field

wiring existing between the Adams Rite power supply and

the control switch used for activating the latch solenoids.

2. CHECK to see is there is a defective control switch existing

on J3-1 and J3-2, or on J3-3 and J3-4.

OUT1 and OUT2 lights do light in response to input switches

1. CHECK to see if there is an open connection in the field

wiring existing between the Adams Rite power supply and

the exit device.

2. VERIFY using a resistance check.

3. IF previous suggestions do not solve the problem,

AND one exit device works and one does not,

THEN PROP the door open,

AND CONNECT a voltmeter across the black and white

leads coming from the exit device,

AND ACTIVATE the malfunctioning exit device.

4. IF the voltmeter measures approximately 24 VDC at the time

of activation, but the latch does not budge,

THEN the SE PCBA is not activating the motor,

AND REPLACE the exit device.

Exit devices retract even though the control switch has not

been activated

1. CHECK to see if a maintained control switch is being used

and is in the closed position.

2. IF the control switch is suspected to be defective,

THEN DISCONNECT and TEST the control switch to verify,

AND REPLACE or REWIRE, as necessary.

ADAMS RITE

10027 S. 51st St. Ste 102

Phoenix, AZ 85044

Tel: 1-800-872-3267

Mon–Fri: 6:00am - 4:00pm PDT

Fax: 1-800-232-7329

www.adamsrite.com

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cerradura de puerta de Assa Abloy

Assa Abloy

Assa Abloy Code Handle Manual

Assa Abloy

Assa Abloy MSL mFlipLock basis Manual de usuario

Assa Abloy

Assa Abloy Corbin Russwin Access 600 CL33600 TCRNE1... Manual de usuario

Assa Abloy

Assa Abloy SARGENT7800 Series Manual de usuario

Assa Abloy

Assa Abloy 1125 Series Guía del usuario

Assa Abloy

Assa Abloy Effeff 809M Manual de usuario

Assa Abloy

Assa Abloy Pyramid Manual de usuario

Assa Abloy

Assa Abloy Corbin Russwin Access 700 ED5000N Series Manual de usuario

Assa Abloy

Assa Abloy Corbin Russwin BLSS ML2000 Series Manual de usuario

Assa Abloy

Assa Abloy 118 Series Manual de usuario

Assa Abloy

Assa Abloy KESO KEK i-handle S Manual del operador

Assa Abloy

Assa Abloy HES 9400 Instrucciones de funcionamiento

Assa Abloy

Assa Abloy Arrow Revolution U4A-YRHCPZW0 Especificaciones técnicas

Assa Abloy

Assa Abloy Yale Real Living Assure Lock YRC256 Especificaciones técnicas

Assa Abloy

Assa Abloy HES Aperio ES100-15 Manual

Assa Abloy

Assa Abloy effeff MAGG1200SM Manual de usuario

Assa Abloy

Assa Abloy Lockwood Standalone Manual

Assa Abloy

Assa Abloy SARGENT IN120 Manual de usuario

Assa Abloy

Assa Abloy Sargent KP Series Manual de instalación

Assa Abloy

Assa Abloy Yale Conexis L1 Manual de usuario

Assa Abloy

Assa Abloy Sargent PE8300 Series Manual de usuario

Assa Abloy

Assa Abloy Corbin Russwin EcoFlex NAC Series Instrucciones de montaje

Assa Abloy

Assa Abloy Effeff 843G Manual de usuario

Assa Abloy

Assa Abloy Sargent PE8800 Series Manual de usuario

Manuales populares de Cerradura de puerta de otras marcas

We.lock

We.lock SECBNEBL51 Manual de usuario

Iseo

Iseo MA1A Manual de usuario

ID Lock

ID Lock 150 Manual de usuario

Lockly

Lockly ACCESS TOUCH PRO Manual de usuario

iLoq

iLoq G50S Manual de usuario

SDC

SDC Z7835 Manual de usuario

ilco

ilco 452 Manual de usuario

Samsung

Samsung shs-h705 Manual de usuario

TRU-BOLT

TRU-BOLT 08102017 Manual de usuario

CDVI

CDVI 500-LADJ Manual de usuario

Igloohome

Igloohome Deadbolt 2S Metal Grey Instrucciones de instalación y mantenimiento

eSSL

eSSL FL-300 Manual de usuario

JAKO

JAKO JKBTNX4 Manual de usuario

Dorma

Dorma MUNDUS PREMIUM GK 50 Guía del usuario

SCOOP

SCOOP Pullbloc 4.1 FS Panik Manual de usuario

Yale

Yale MORTISE 8800 SERIES Manual de usuario

Siegenia

Siegenia KFV AS3500 Manual de usuario

Saflok

Saflok Quantum ädesē RFID Manual de usuario