ASROCK PE PRO-HT Manual de usuario

PE Pro-HT

User Manual

Version 1.0

Published January 2003

No part of this manual may be reproduced, transcribed, transmitted, or translated in

any language, in any form or by any means, except duplication of documentation by

the purchaser for backup purpose, without written consent of ASRock Inc.

Products and corporate names appearing in this manual may or may not be regis-

tered trademarks or copyrights of their respective companies, and are used only for

identification or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:

Specifications and information contained in this manual are furnished for informa-

tional use only and subject to change without notice, and should not be constructed

as a commitment by ASRock. ASRock assumes no responsibility for any errors or

omissions that may appear in this manual.

With respect to the contents of this manual, ASRock does not provide warranty of

any kind, either expressed or implied, including but not limited to the implied warran-

ties or conditions of merchantability or fitness for a particular purpose.

In no event shall ASRock, its directors, officers, employees, or agents be liable for

any indirect, special, incidental, or consequential damages (including damages for

loss of profits, loss of business, loss of data, interruption of business and the like),

even if ASRock has been advised of the possibility of such damages arising from

any defect or error in the manual or product.

ASRock Website: http://www.asrock.com

Contents

1 Introduction ................................................... 4

1.1 Package Contents ......................................................... 4

1.2 Specifications ................................................................ 4

1.3 Motherboard Layout ...................................................... 6

1.4 ASRock I/OTM .................................................................. 7

2 Installation...................................................... 8

2.1 Screw Holes ................................................................. 8

2.2 Pre-installation Precautions ........................................... 8

2.3 CPU Installation .............................................................. 8

2.4 Installation of Heatsink and CPU fan ............................. 9

2.5 Installation of Memory Modules (DIMM) ......................... 9

2.6 Expansion Slots ............................................................. 10

2.7 Jumpers Setup .............................................................. 10

2.8 Connectors .................................................................... 11

3 BIOS Setup ...................................................... 14

3.1 BIOS Setup Utility ........................................................... 14

3.1.1 BIOS Menu Bar ....................................................... 14

3.1.2 Legend Bar ............................................................. 14

3.2 Main Menu...................................................................... 15

3.3 Advanced, Security, Power, Boot, and Exit Menus ..... 17

4 Software Support ........................................... 18

4.1 Installing Operating System ........................................... 18

4.2 Support CD Information ................................................. 18

4.2.1 Running Support CD ............................................... 18

4.2.2 Drivers Menu .......................................................... 18

4.2.3 Utilities Menu ........................................................... 18

4.2.4 ASRock PC-DIY Live Demo Program ...................... 18

4.2.5 Contact Information ................................................ 18

Appendix: Advanced BIOS Setup ................... 19

1. Advanced Menu ............................................................... 19

2. Security Menu................................................................... 22

3. Power Menu ..................................................................... 23

4. Boot Menu ......................................................................... 24

5. Exit Menu .......................................................................... 24

Chapter 1 Introduction

Thank you for purchasing ASRock PE Pro-HT motherboard, a reliable motherboard

produced under ASRock’s consistently stringent quality control. It delivers excellent

performance with robust design conforming to ASRock’s commitment to quality and

endurance.

Chapter 1 and 2 of this manual contain introduction of the motherboard and step-by-

step installation guide for new DIY system builders. Chapter 3 and 4 contain basic

BIOS setup and Support CD information.

For advanced users’ reference, the Appendix appearing on page 19 offers more

advanced BIOS setup information.

1.1 Package Contents

ASRock PE Pro-HT motherboard (ATX form factor: 12" x 9.6", 30.5 x 24.4 cm)

ASRock PE Pro-HT Quick Installation Guide

ASRock Intel-SiS Series Support CD

1 cable for IDE devices (1 x ATA 66/100/133)

1 cable for floppy drive (1 x ribbon cable)

1 ASRock I/O shield

1.2 Specifications

Platform: ATX form factor (12" x 9.6", 30.5 x 24.4 cm)

CPU: Socket 478 for Intel®Pentium® 4/ Celeron®processor

Chipsets: North Bridge: SiS 645DXHT chipsets, standard FSB 533 MHz,

supports Hyper-Threading Technology (see CAUTION 1);

South Bridge: Supports USB 2.0, ATA 133

Clock Generator:100 MHz - 200MHz

Memory: 2 slots for DDR: DIMM1 and DIMM2, Max. 2GB

(PC1600 / PC2100 / PC2700);

2 slots for SDR: DIMM3 and DIMM4, Max. 2GB (PC100/ PC133)

IDE: IDE1: ATA 133 / Ultra DMA Mode 6;

IDE2: ATA 133 / Ultra DMA Mode 6;

Can connect up to 4 IDE devices

Floppy Port: Supports floppy disk drive

Audio: 5.1 channels AC’97 Audio

LAN: Speed: 802.3u (10/100 Ethernet), supports Wake-On-LAN

Hardware Monitor: CPU temperature sensing (ASRock U-COP);

CPU overheat shutdown to protect CPU life (ASRock U-COP)

(see CAUTION 2); Chassis temperature sensing;

Voltage monitoring: +12V, +5V, +3V, Vcore;

CPU fan tachometer; Chassis fan tachometer

PCI slots: 6 slots with PCI Specification 2.2

AGP slot: 1 universal AGP slot, supports 3.3v / 1.5v, 4X / 2X / 1X AGP card

USB 2.0: 4 default USB 2.0 ports and one extra set of header for 2

additional USB 2.0 ports upgrade (see CAUTION 3)

ASRock I/OTM :PS/2: 1 keyboard port / 1 mouse port;

1 RJ 45 port;

4 rear default USB 2.0 ports;

1 serial port: COM1;

1 parallel port: ECP/EPP support;

Audio Jack: Line Out/ Line In/ Microphone + 1 Game port

BIOS: AMI legal BIOS;

Supports “Plug and Play”;

ACPI 1.1 compliance wake up events;

Supports jumperfree;

SMBIOS 2.3.1 support;

OS: Microsoft®Windows®98SE / ME / 2000 / XP compliant

CAUTION!

1. About the setting of “Hyper-Threading Technology”, please check

page 19.

2. While CPU overheat is detected, the system will automatically

shutdown. Please check if the CPU fan on the motherboard

functions properly before you resume the system. To improve heat

dissipation, remember to spray thermal grease between the CPU

and the heatsink when you install the PC system.

3. Power Management for USB 2.0 works fine under Microsoft®

Windows®XP. It may not work properly under Microsoft®

Windows®98/ME/2000. Please refer to Microsoft®official

document at

http://www.microsoft.com/HWDEV/BUS/usb/USB2support.asp

1.3 Motherboard Layout

1 ATX power connector (ATXPWR1) 14 Infrared module connector (IR1)

2 CPU socket 15 External speaker connector (SPEAKER1)

3 CPU fan connector (CPU_FAN1) 16 South Bridge controller

4 North Bridge controller 17 Clear CMOS (CLRCMOS1)

5 184-pin DDR DIMM slots (DDR1-2, Blue) 18 PCI slots (PCI 1- 6)

6 168-pin SDRAM DIMM slots (SDR1-2, Black) 19 Audio CODEC

7 Primary IDE connector (IDE1, Blue) 20 Front panel audio connector (AUDIO1)

8 Secondary IDE connector (IDE2, Black) 21 LAN PHY

9 Chassis fan connector (CHA_FAN1) 22 PS2_USB_PWR1 jumper

10 Floppy connector (FLOPPY1) 23 Internal audio connectors: AUX1 (White)

11 Flash Memory 24 Internal audio connectors: CD1 (Black)

12 System panel connector (PANEL1) 25 AGP slot

13 USB 2.0 header (USB45)

SiS

645DX

Chipset

PS2_USB_PWR1

Accelerated Graphics Port

PCI 1

PCI 2

PCI 3

PCI 4

PCI 5

30.5cm (12.0 in)

24.4cm (9.6 in)

Audio CODEC

AUX1

Mic

GAME AUDIO1

USB01

LAN

USB23

Mic in

Line out

GAME AUDIO1

PARALLEL PORT

PS/2

Mouse

PS/2

Keyboard

COM1

SiS

South

Bridge

Audio1

CPU_FAN1

PANEL 1

SPEAKER1

Line

Line in

CMOS

Battery

IDE1

FLOPPY1

HDLED RST

PLED PWRBTN

USB45

IR1

mPGA478B

PCI 6

CLRCMOS1

CHA_FAN1

IDE2

SDR DIMM1 (64 bit, 168-pin module)

SDR DIMM2 (64 bit, 168-pin module)

DDR DIMM1 (64/72 bit, 184-pin module)

DDR DIMM2 (64/72 bit, 184-pin module)

2MB

BIOS

Super

I/O

CD1

LAN

PHY

PE PRO-HT

ATA 13 3

USB2.0

5.1CH

1.4 ASRock I/OTM

1 Parallel port 6 Line Out (Lime)

2 RJ-45 port 7 USB 2.0 ports

3 Game port 8 Serial port (COM1)

4 Microphone (Pink) 9 PS/2 keyboard port (Purple)

5 Line In (Light Blue) 10 PS/2 mouse port (Green)

123

4567

910

Chapter 2 Installation

PE Pro-HT is an ATX form factor (12" x 9.6", 30.5 x 24.4 cm) motherboard. Before

you install the motherboard, study the configuration of your chassis to ensure that

the motherboard fits into it.

Make sure to unplug the power cord before installing or removing the

motherboard. Failure to do so may cause physical injuries to you

and damages to motherboard components.

2.1 Screw Holes

Place screws into the holes indicated by circles to secure the motherboard

to the chassis.

Do not over-tighten the screws! Doing so may damage the

motherboard.

2.2 Pre-installation Precautions

Take note of the following precautions before you install motherboard components

or change any motherboard settings.

1. Unplug the power cord from the wall socket before touching any component.

2. To avoid damaging the motherboard components due to static electricity, NEVER

place your motherboard directly on the carpet or the like. Also remember to use

a grounded wrist strap or touch a safety grounded object before you handle

components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a grounded antistatic pad or

in the bag that comes with the component.

Before you install or remove any component, ensure that the power is switched

off or the power cord is detached from the power supply. Failure to do so may cause

severe damage to the motherboard, peripherals, and/or components.

2.3 CPU Installation

Step 1. Unlock the socket by lifting the lever up to a 90 angle.

Step 2. Position the CPU directly above the socket such that its marked corner

matches the base of the socket lever.

Step 3. Carefully insert the CPU into the socket until it fits in place.

168-pin RAM 184-pin RAM

The CPU fits only in one correct orientation. DO NOT force the

CPU into the socket to avoid bending of the pins.

Step 4. When the CPU is in place, press it firmly on the socket while you push down

the socket lever to secure the CPU. The lever clicks on the side tab to

indicate that it is locked.

Step 1 Step 2, 3 Step 4

2.4 Installation of CPU Fan and Heatsink

Intel®Pentium®4 CPU requires larger heatsink and cooling fan. Thermal

grease between the CPU and the heatsink is also needed to improve heat

transfer. Make sure that the CPU and the heatsink are securely fastened and

in good contact with each other. For proper installation, please kindly

refer to the instruction manuals of vendors of CPU fan and heatsink.

2.5 Installation of Memory Modules (DIMM)

SDRAM (Synchronous DRAM) DIMM (Dual In-line Memory Module) has 168 pins

and DDR (Double Data Rate) SDRAM DIMM has 184 pins.

Please make sure to disconnect power supply before adding or

removing DIMMs or the system components.

The 168-pin SDRAM DIMM slot (black) and 184-pin DDR DIMM slot (blue) can be easily

distinguished by the fool-proof design.

Please do not use both 168-pin SDRAM DIMM and 184-pin DDR DIMM

at the same time. To optimize the compatibility, it is not recommended

to use two different models of the DIMMs at the same time.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward.

Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break

on the slot.

Step 3. Firmly insert the DIMM into the slot until the retaining clip snap back in place

and the DIMM is properly seated.

2.6 Expansion Slots (PCI and AGP Slots)

There are 6 PCI slots and 1 AGP slot on PE Pro-HT motherboard.

PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI

interface.

AGP slot: The AGP slot is used to install a graphics card.

The ASRock AGP slot has a special locking mechanism which

can securely fasten the graphics card inserted.

Installing an expansion card

Step 1. Before installing the expansion card, read the documentation of the

expansion card and make necessary hardware settings for the card.

Step 2. Remove the system unit cover (if your motherboard is already installed in a

chassis).

Step 3. Remove the bracket facing the slot that you intend to use. Keep the screw

for later use.

Step 4. Align the card connector with the slot and press firmly until the card is

completely seated on the slot.

Step 5. Fasten the card to the chassis with screws.

Step 6. Replace the system cover.

2.7 Jumpers Setup

The illustration shows how jumpers are setup.

When the jumper cap is placed on pins, the jumper

is “SHORT”. If no jumper cap is placed on pins,

the jumper is “OPEN”. The illustration shows a

3-pin jumper whose pin1 and pin2 are “SHORT”

when jumper cap is placed on these 2 pins.

Tabla de contenidos

Otros manuales de Placa madre de ASROCK

ASROCK

ASROCK K10N78 - V1.1 Manual de usuario

ASROCK

ASROCK H310CM-HDVP Manual de usuario

ASROCK

ASROCK H570 Steel Legend Manual de usuario

ASROCK

ASROCK FM2A55M-VG3 Manual de usuario

ASROCK

ASROCK IMB-182 Manual de usuario

ASROCK

ASROCK AD2550RA/U3S3 Manual de usuario

ASROCK

ASROCK 880GMH USB3 R2.0 Manual de usuario

ASROCK

ASROCK B760M PRO RS Manual de usuario

ASROCK

ASROCK P43ME Manual de usuario

ASROCK

ASROCK A330ION Manual de usuario

ASROCK

ASROCK IMB-1220 Manual de usuario

ASROCK

ASROCK PHANTOM GAMING Z790M PC LIGHTNING/D4 Manual de usuario

ASROCK

ASROCK X99M Extreme4 Manual de usuario

ASROCK

ASROCK H610M-H2/M.2 D5 Manual de usuario

ASROCK

ASROCK IMB-171-D Manual de servicio

ASROCK

ASROCK FM2A75 Pro4-M Manual de usuario

ASROCK

ASROCK A785GXH128M Manual de usuario

ASROCK

ASROCK H81M-ITX Manual de usuario

ASROCK

ASROCK 790GX Pro Manual de usuario

ASROCK

ASROCK WOLFDALE1333-DVI Manual de usuario

ASROCK

ASROCK H270 PRO4 Manual de usuario

ASROCK

ASROCK J4005DC-ITX Manual de usuario

ASROCK

ASROCK B760M-HDV/M.2 D4 Manual de usuario

ASROCK

ASROCK Z390M-STX MXM Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario