ASROCK K7VT4A PRO Manual de usuario

K7VT4A+

User Manual

Version 1.0

Published May 2004

No part of this manual may be reproduced, transcribed, transmitted, or translated in

any language, in any form or by any means, except duplication of documentation by

the purchaser for backup purpose, without written consent of ASRock Inc.

Products and corporate names appearing in this manual may or may not be regis-

tered trademarks or copyrights of their respective companies, and are used only for

identification or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:

Specifications and information contained in this manual are furnished for informa-

tional use only and subject to change without notice, and should not be constructed

as a commitment by ASRock. ASRock assumes no responsibility for any errors or

omissions that may appear in this manual.

With respect to the contents of this manual, ASRock does not provide warranty of

any kind, either expressed or implied, including but not limited to the implied warran-

ties or conditions of merchantability or fitness for a particular purpose.

In no event shall ASRock, its directors, officers, employees, or agents be liable for

any indirect, special, incidental, or consequential damages (including damages for

loss of profits, loss of business, loss of data, interruption of business and the like),

even if ASRock has been advised of the possibility of such damages arising from any

defect or error in the manual or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

ASRock Website: http://www.asrock.com

Contents

1. Introduction ....................................................... 4

1.1 Package Contents................................................................ 4

1.2 Specifications...................................................................... 5

1.3 Motherboard Layout ............................................................ 7

1.4 ASRock I/OTM .......................................................................................................................... 8

2. Installation ......................................................... 9

Pre-installation Precautions ......................................................... 9

2.1 CPU Installation .................................................................... 10

2.2 Installation of CPU Fan and Heatsink .................................. 10

2.3 Installation of Memory Modules (DIMM)............................... 11

2.4 Expansion Slots (PCI and AGP Slots) ................................. 12

2.5 Jumpers Setup .................................................................... 13

2.6 Onboard Headers and Connectors .................................... 15

3. BIOS Setup ......................................................... 17

3.1 BIOS Setup Utility ................................................................. 17

3.1.1 BIOS Menu Bar .......................................................... 17

3.1.2 Legend Bar ................................................................ 18

3.2 MainMenu ............................................................................ 18

3.3 Advanced, Security, Power, Boot, and Exit Menus ........... 20

4. Software Support .............................................. 21

4.1 Install Operating System ...................................................... 21

4.2 Support CD Information ........................................................ 21

4.2.1 Running Support CD .................................................. 21

4.2.2 Drivers Menu ............................................................. 21

4.2.3 Utilities Menu .............................................................. 21

4.2.4 ASRock “PC-DIY LiveDemo” Program ...................... 21

4.2.5 Contact Information .................................................... 21

Appendix ............................................................... 22

1. Advanced BIOS Setup Menu............................................... 22

2. Security Setup Menu ........................................................... 27

3. Power Setup Menu .............................................................. 28

4. Boot Setup Menu ................................................................. 29

5. Exit Menu .............................................................................. 30

1. Introduction

Thank you for purchasing ASRock K7VT4A+ motherboard, a reliable motherboard

produced under ASRock’s consistently stringent quality control. It delivers excellent

performance with robust design conforming to ASRock’s commitment to quality and

endurance.

Chapter 1 and 2 of this manual contain introduction of the motherboard and step-by-

step installation guide. Chapter 3 and 4 contain basic BIOS setup and support CD

information. More information of advanced BIOS setup can be found in Appendix on

page 22 for advanced users’ reference.

Because the motherboard specifications and the BIOS software might

be updated, the content of this manual will be subject to change

without notice. In case any modifications of this manual occur, the

updated version will be available on ASRock website without further

notice. You may find the latest memory and CPU support lists on

ASRock website as well. ASRock website http://www.asrock.com

1.1 Package Contents

1 x ASRock K7VT4A+ Motherboard

(ATX Form Factor: 12.0-in x 7.0-in, 30.5 cm x 17.8 cm)

1 x ASRock K7VT4A+ Quick Installation Guide

1 x ASRock K7VT4A+ Support CD

1 x Ultra ATA 66/100/133 IDE Ribbon Cable (80-conductor)

1 x 3.5-in Floppy Drive Ribbon Cable

1 xASRock I/OTM Shield

1.2 Specifications

Platform: ATX Form Factor: 12.0-in x 7.0-in, 30.5 cm x 17.8 cm

CPU: Supports Socket A (462 pins) for

AMDAthlonTM / AthlonTM XP / DuronTM processor

Chipsets: North Bridge: VIA KT400A, FSB@333 MHz

South Bridge: VIAVT8235CD, supports USB 2.0, ATA 133

Memory: 2DDRDIMMSlots:DDR1andDDR2

PC3200 (DDR400) for 1DDRDIMM slot, Max. 1GB

PC2100(DDR266)/PC2700(DDR333)for2DDRDIMMslots,

Max. 2GB

IDE: IDE1:ATA133 / UltraDMA Mode 6

IDE2:ATA133 / UltraDMA Mode 6

Supports up to 4 IDE devices

Floppy Port: Supports up to 2 floppy disk drives

Audio: 5.1 channels AC’97 Audio

LAN: Speed: 802.3u (10/100 Ethernet), supports Wake-On-LAN

Hardware Monitor: CPU temperature sensing

Motherboard temperature sensing

CPU overheat shutdown to protect CPU life

(ASRock U-COP)(see CAUTION 1)

CPU fan tachometer

Chassis fan tachometer

Voltage monitoring: +12V, +5V, +3.3V, Vcore

PCI slots: 5 slots with PCI Specification 2.2

AGP slot: 1 AGP slot, supports 1.5V, 8X/4X AGP card (see CAUTION 2)

USB 2.0: 6 USB 2.0 ports:

includes 4 default USB 2.0 ports on the rear panel,

plus one header to support 2 additional USB 2.0 ports

(see CAUTION 3)

ASRock I/OTM:1 PS/2 keyboard port, 1 PS/2 mouse port,

1 serial port: COM1, 1 parallel port: ECP/EPP support,

1 RJ-45 port,

4 default USB 2.0 ports,

Audio Jack: Line Out / Line In / Microphone + Game port

BIOS: AMI legal BIOS, Supports “Plug and Play”,

ACPI 1.1 compliance wake up events,

SMBIOS 2.3.1 support,

CPU frequency stepless control

(only for advanced users’ reference, see CAUTION 4)

OS: Microsoft® Windows® 98 SE / ME / 2000 / XP compliant

CAUTION!

1. While CPU overheat is detected, the system will automatically shutdown.

Before you resume the system, please check if the CPU fan on the

motherboard functions properly and unplug the power cord, then plug it

back again. To improve heat dissipation, remember to spray thermal

grease between the CPU and the heatsink when you install the PC system.

2. Do NOT use a 3.3V AGP card on the AGP slot of this motherboard!

It may cause permanent damage!

3. Power Management for USB 2.0 works fine under Microsoft®Windows®

XP SP1/2000 SP4. It may not work properly under Microsoft®Windows®

98/ME. Please refer to Microsoft®official document at

http://www.microsoft.com/whdc/hwdev/bus/USB/USB2support.mspx

4. Although this motherboard offers stepless control, it is not recommended

to perform over clocking. Frequencies other than the recommended CPU

bus frequencies may cause the instability of the system or damage the

CPU. The CPU host frequency of this motherboard is determined by the

jumper-setting. You must set the FSB jumper according to yourAMD CPU

before you use the “Manual” option as the FSB setting in BIOS setup to

perform over clocking. Please check page 22 for details.

17.8cm (7.0 in)

DDR 1 (64/72 bit, 184-pin module)

DDR2 (64/72 bit, 184-pin module)

PCI2

PCI3

PCI4

PCI5

PCI1

1.5V_AGP1

USB45

SPEAKER1

HDLED RST

PLED PWRBTN

PANEL1

IR1

2MB

BIOS

FLOPPY1

SUPER

I/O

AUDIO1

JR1

JL1

CLRCMOS2

VIA

VT8235

CPU_FAN1

CHA_FAN1

CMOS

BATTERY

PS2_USB_PWR1

IDE1 IDE2

USB2.0

5.1CH

ATA133

FSB333

K7VT4A+

VIA

KT400A

CHIPSET

ATXPWR1

AUX1

CD1

Mic

GAME AUDIO1

MIC IN

LINE OUT

GAME_ AUDIO1

Line

LINE IN

USB 2.0

PORTS

LAN

PARALLEL PORT

PS/2

MOUSE

PS/2

KEYBOARD

SERIAL

PORT

(COM1)

30.5cm (12.0 in)

LAN

PHY

AUDIO

CODEC

12 36

1819

FID3

FID2

FID1

FID0

FID4 1

DDR400

AGP 8X

PWR_LED1

USB 2.0

PORTS

1FSB_SEL0

1FSB_SEL1

FSB_SEL2

SOCKET 462

1.3 Motherboard Layout

1 PS2_USB_PWR1 Jumper 14 Power LED Connector (PWR_LED1)

2 CPU Fan Connector (CPU_FAN1) 15 System Panel Connector (PANEL1)

3 CPU Socket 16 Chassis Speaker Connector (SPEAKER 1)

4 North Bridge Controller 17 USB 2.0 Connector (USB45, Blue)

5 184-pin DDR DIMM Slots (DDR1- 2) 18 Infrared Module Connector (IR1)

6 ATX Power Connector (ATXPWR1) 19 Clear CMOS Jumper (CLRCMOS2)

7 Secondary IDE Connector (IDE2, Black) 20 Flash Memory

8 Primary IDE Connector (IDE1, Blue) 21 PCI Slots (PCI1- 5)

9 AGP Slot (1.5V_AGP1) 22 Front Panel Audio Connector (AUDIO1)

10 FSB Select Jumpers 23 JR1 / JL1 Jumpers

(FSB_SEL0,FSB_SEL1, FSB_SEL2) 24 Internal Audio Connector: CD1 (Black)

11 South Bridge Controller 25 Internal Audio Connector: AUX1 (White)

12 Chassis Fan Connector (CHA_FAN1) 26 J1 Jumper (FID0, FID1, FID2, FID3, FID4)

13 Floppy Connector (FLOPPY1)

1.4 ASRock I/OTM

1 Parallel Port 6 Line Out (Lime)

2 RJ-45 Port 7 USB 2.0 Ports

3 Game Port 8 Serial Port (COM1)

4 Microphone (Pink) 9 PS/2 Keyboard Port (Purple)

5 Line In (Light Blue) 10 PS/2 Mouse Port (Green)

4567

910

2. Installation

K7VT4A+ is an ATX form factor (12.0-in x 7.0-in, 30.5 cm x 17.8 cm) motherboard.

Before you install the motherboard, study the configuration of your chassis to en-

sure that the motherboard fits into it.

Pre-installation Precautions

Take note of the following precautions before you install motherboard

components or change any motherboard settings.

Before you install or remove any component, ensure that the

power is switched off or the power cord is detached from the

power supply. Failure to do so may cause severe damage to the

motherboard, peripherals, and/or components.

1. Unplug the power cord from the wall socket before touching any

component.

2. To avoid damaging the motherboard components due to static

electricity, NEVER place your motherboard directly on the carpet or

the like. Also remember to use a grounded wrist strap or touch a

safety grounded object before you handle components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a grounded anti-

static pad or in the bag that comes with the component.

5. When placing screws into the screw holes to secure the motherboard

to the chassis, please do not over-tighten the screws! Doing so may

damage the motherboard.

2.1 CPU Installation

Step 1. Unlock the socket by lifting the lever up to a 90oangle.

Step 2. Position the CPU directly above the socket such that its marked corner

matches the base of the socket lever.

Step 3. Carefully insert the CPU into the socket until it fits in place.

The CPU fits only in one correct orientation. DO NOT force the

CPU into the socket to avoid bending of the pins.

Step 4. When the CPU is in place, press it firmly on the socket while you push

down the socket lever to secure the CPU. The lever clicks on the side tab

to indicate that it is locked.

2.2 Installation of CPU Fan and Heatsink

AMDAthlonTM /AthlonTM XP/DuronTM family CPUs with a speed of 600 MHz and

higher require larger heatsink and cooling fan. Thermal grease between the

CPU and the heatsink is also needed to improve heat transfer. Make sure that

the CPU and the heatsink are securely fastened and in good contact with

each other. Then connect the CPU fan to the CPU_FANconnector (CPU_FAN1,

see page 7, No. 2). For proper installation, please kindly refer to the instruc-

tion manuals of the CPU fan and heatsink vendors.

Step 1 Step 2, 3 Step 4

Otros manuales para K7VT4A PRO

Tabla de contenidos

Idiomas:

Otros manuales de Placa madre de ASROCK

ASROCK

ASROCK 880GMH/U3S3 Manual de usuario

ASROCK

ASROCK IMB-1001 Manual de usuario

ASROCK

ASROCK P55 DELUXE - V1.1 Manual de usuario

ASROCK

ASROCK 880GMH-USB3 - V1.0 Manual de usuario

ASROCK

ASROCK H310M-HDV Manual de usuario

ASROCK

ASROCK 960GM/U3S3 FX Manual de usuario

ASROCK

ASROCK P55DE3 Manual de usuario

ASROCK

ASROCK P55DE PRO - V1.0 Manual de usuario

ASROCK

ASROCK B150M Pro4S/D3 Manual de usuario

ASROCK

ASROCK AM1H-M Manual de usuario

ASROCK

ASROCK Rack E3C224D4M-16RE Manual de usuario

ASROCK

ASROCK 760GM-S3 Manual de usuario

ASROCK

ASROCK Q87M vPro Manual de usuario

ASROCK

ASROCK H77WS-DL Manual de usuario

ASROCK

ASROCK A75 Pro4 MVP Manual de usuario

ASROCK

ASROCK H410M-HDV/M.2 Manual de usuario

ASROCK

ASROCK J3455-NUC IPC Manual de usuario

ASROCK

ASROCK 775Twins-HDTV R2.0 Manual de usuario

ASROCK

ASROCK PHANTOM GAMING X670E PG Lightning Manual de usuario

ASROCK

ASROCK Z87E-ITX Manual de usuario

ASROCK

ASROCK A520M-HDV Manual de usuario

ASROCK

ASROCK B360M-ITX/ac Manual de usuario

ASROCK

ASROCK G41M-VGS3 Manual de usuario

ASROCK

ASROCK H270M-ITX/ac Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario