Ashford WILD Manual de usuario
Inside spring
washer
INSTRUCTIONS
Ashford Guarantee
Thank you for purchasing this Ashford product. In the unlikely event there is
any fault in manufacture we will replace the item. To validate our guarantee
please visit our website or write to us.
Ashford Handicrafts Limited
Factory and Showroom: 415 West Street
PO Box 474, Ashburton 7700 New Zealand
Telephone 64 3 308 9087 Facsimile 64 3 308 8664
WILD DRUM CARDER
Create your own fabulous fun and funky art yarns by blending fibres, fabrics, ribbon, feathers, noils, cocoons, paper and more...
Prepare 40gm (1½oz) batts.
Use the adjustable packer brush to smooth and pack more fibre onto the large drum.
Extra long 72 ppsi teeth.
Adjustable drum clearance to suit your fibre.
Rubber feet to stop it from slipping.
Assembled and lacquered - ready to use.
Includes doffer (awl),
cleaning brush and clamps.
Assembly
Attach the handle as shown. Note: Place a spring washer on first, thread on the handle, the second spring washer and lock in
place with the nylon knob. Thread the 2 screw eyes into the holes in the side of the carder. Use them to store the doffer. Place
the drive band onto the pulleys as illustrated. When not in use, remove the drive band to avoid it stretching. Store the doffer in
the 2 screw eyes on the side of the carder. Store the cleaning brush under the feed-in tray. Assemble the 2 clamps.
Drive band
Doffer (Awl) eyes
Clamps
*If the handle
obstructs the doffer
strip, replace the in-
side spring washer
with the optional
flat 22x10 washer.
Handle
Doffer Strip
How to Use the Wild Carder
Clamp your Wild Carder to a bench or table.
Fleece - We recommend you lightly wash your fleece prior to
carding. Tease the tips of the staples with a flick carder, pull
the staple apart sideways, place on the feed-in tray and turn
the handle clockwise. Card small amounts of fibre at a time.
Allow the fibres to feed-in, don’t hold back.
Prepared fibre - Peel sliver into strips, stretch to lengthen
and spread it out sideways. Place on the feed-in tray and turn
handle clockwise. Allow the fibres to feed-in, don’t hold back.
NOTE: For easy carding spread out your fibre as you place on
the feed-in tray.
Wild carding - Prepare short pieces of fibre, fabric, ribbon,
feathers, noils, cocoons, paper etc. Make a sliver sandwich -
Place your embellishments on top and cover with a thin layer
of sliver.
Adjust the packer brush to pack the fibres down into the teeth
of the large drum.
Once the teeth on the large drum are full of fibre or fibre starts
accumulating on the small drum, stop carding.
NOTE: Ensure all fibres remain between the guide pegs on the
feed-in tray. This will avoid fibres being caught around the
shafts.
Removing the batt
Loosen the knob holding the packer brush and twist it up off
the large drum. Turn the drum until the doffer strip is to the
top.
Part the batt with the doffer, taking care the doffer runs in the
groove in the doffer strip.
Pull the batt down over the back beam to remove it cleanly
from the drum.
Maintenance
Apply a drop of oil occasionally to all bearings.
The gap between the teeth may be adjusted to suit your fibre.
The carder comes factory set at our recommended spacing
of 0-1mm. For fine fibres without bulk, you may use a closer
setting or for coarser bulky fibres you may use a slightly wider
setting. To adjust the gap, remove the drive band. Loosen
the 2 bolts and use the nail supplied to rotate the 2 eccentric
bearings. Tighten the 2 bolts and replace the drive band.
Always remove the drive band when not in use to avoid it
stretching.
For more detailed carding instructions, hints and inspiration,
we recommended the Ashford Book of Carding by Jo Reeve.
It has 92 colourful pages covering flick, hand and drum
carding, colour theory and 4 gorgeous projects.
Happy Carding! WDC010518V6
Otros manuales de Cardador de Ashford
