Aristel AN6311 Manual de usuario
Public Address System
IP Network Ceiling Speaker AN6311
User Manual
Thank you for using our public address system. Please read this User Manual carefully to make better use of
this equipment.
Edition v2.1
Aristel
This page is left blank for users’ notes.
Edition v2.1
Aristel
About the User Manual
This User Manual is available and effective upon completion of development
of the AN6311 Ceiling Speaker. The User Manual includes system description,
matters needing attentions in use, instructions on system connection, instructions
on use of product and technical specifications of the terminal. Please read this
User Manual carefully before connection, installation and use and operate in
accordance with corresponding instructions in the Manual.
This symbol on the rear panel indicates matters needing attention, please use or operate the
product in accordance with corresponding instructions.
Please keep this User Manual for future use.
PoE—V2.3
Edition 2.1
Edition v2.1
Aristel
* * IP Network Ceiling Speaker
Contents
I. Product Description.................................................................................................................................................. 1
1.1 About AN6311 Ceiling Speaker.........................................................................................................................1
1.2 Features................................................................................................................................................................1
II. Appearance Description.......................................................................................................................................... 2
2.1 Side Panel............................................................................................................................................................ 2
III. Connection Diagram ............................................................................................................................................ 3
3.1 AN6311Application Diagram in the System........................................................................................................3
3.2 AN6311 Interface Connection Diagram............................................................................................................... 4
IV. Terminal WEB Function Settings.......................................................................................................................5
V. IP Address Setting of the Terminal on the Host.....................................................................................................8
VI. Installation..............................................................................................................................................................9
Specification............................................................................................................................................................... 11
Packing List................................................................................................................................................................ 11
Edition v2.1
Aristel
* * IP Network Ceiling Speaker
1
I. Product Description
1.1 About AN6311 Ceiling Speaker
The AN6311 ceiling speaker is a network full-digital & analog-digital conversion signal
processor based on the SIP transmission protocol. It can be mounted in any place accessible to a
network. The remote audio data steam can output as an audio signal through the equipment with
intelligent host control.
1.2 Features
Can be mounted to any place accessible to a network.
Supports maximum 48kHz sampling rate, 16bit digital audio stream decoding.
Built-in 2×9W digital amplifier.
Can play background music, emergency paging, alarm signals from the system host.
Can operate as a loud ringer for PBX systems.
Local output volume and local play status can be controlled.
Provide a complete interface that complies with the IEEE 802.3af / at standard of the Power over
Ethernet (PoE) system and a DC15V power supply interface, with two optional power supply
modes for switching.
Appealing design and easy to install.
Edition v2.1
Aristel
* * IP Network Ceiling Speaker
2
II. Appearance Description
2.1 Side Panel
1 Power supply interface
DC power supply. (Note: You can use this interface for power supply when not using PoE power
supply)
2PoE interface
Connect a PoE switch with 48V with AT mode output when used for data and power
transmission.
3Micro SD
Reserved for later .
4Speaker output
Built-in 2×9W digital amplifier (Note: Please be careful when using the two simultaneous outputs
due to the power limitation of the PoE switch), which can only drive its own speaker with
constant resistance (8Ω).
DC/+15V PoE INPUT
Mircos SD
SPEAKER
OUTPUT
+
DC/+15V PoE INPUT
Mircos SD
SPEAKER
OUTPUT
+
1 2 3 4
DC/+15V PoE INPUT
Mircos SD
SPEAKER
OUTPUT
+
162mm
185mm
114mm
170-175mm
Edition v2.1
Aristel
* * IP Network Ceiling Speaker
3
III. Connection Diagram
3.1 AN6311 Application Diagram in the System
Note:
①The above figure illustrates the connection diagram of the AN6311 approximate application,
Please refer to the user manual of the network control host for the whole system connection.
②The above figure is for illustrative purposes only. Please refer to the system connection diagram for
specific connection.
③The AN6311 in the system must be powered by 48V IEEE802.3at standard switch port, and set the
corresponding address before connecting with the host.
④Due to the PoE power supply mechanism, it is normal for the device to be temporarily
disconnected and online when it is powered on.
Other devices of the IP PA System
Other networks or
devices of the IP PA
System
Control host of the IP PA System
Ethernet
POWER
OFF ON
USB
NETWORK PUBLIC ADDRESS CENTRE
EMC MIC
FULL ALARMING
COMPACT DISC DRIVER
Terminal
Terminal
Terminal
Terminal
48V, AT
mode PoE
switch
48V, AT
mode PoE
switch
48V, AT
mode PoE
switch
48V, AT
mode PoE
switch
Edition v2.1
Aristel
* * IP Network Ceiling Speaker
4
3.2 AN6311 Interface Connection Diagram
Interface connection diagram
48V, AT mode PoE switch
DC/+15V PoE INPUT
Mircos SD
SPEAKER
OUTPUT
+
DC/+15V PoE INPUT
Mircos SD
SPEAKER
OUTPUT
+
1 2 3 4
DC/+15V PoE INPUT
Mircos SD
SPEAKER
OUTPUT
+
162mm
185mm
114mm
170-175mm
AN6311 speaker
Dedicated ceiling speakers
Edition v2.1
Aristel
* * IP Network Ceiling Speaker
5
IV. Terminal WEB Function Settings
Make sure that the device and your computer are on the same LAN network. After connecting the
computer and the terminal, enter the IP address displayed on the equipment label (default 192.168.5.3 ) into
the IE browser as shown below, and then enter the user name: admin, password: 123456 for login.
After successful login, enter the interface as shown below.
1) System Status
Can view the current software version, system time and device network details.
2) Network Settings
The network connection mode of the device. Please select an appropriate network mode according to the actual
network environment. The device provides two network connection modes:
Static IP mode (Static): You can select this option. After selecting, fill in the static IP address, subnet mask,
gateway, DNS domain name, primary DNS, and backup DNS.
DHCP mode: In this mode, network-related information will be automatically obtained from the DHCP server,
Edition v2.1
Aristel
* * IP Network Ceiling Speaker
6
and you do not need to manually enter these fields.
3 SIP Settings
Registration status: The SIP registration status of the device can be displayed. If the registration is successful,
it will be displayed as registered, while if it is not successful, it will be displayed as unregistered.
Username: The account for SIP registration.
Password: The password of the account for SIP registration.
Server address: Server address for SIP registration.
Server port: Server signaling port for SIP registration.
SIP automatic answering switch: When it is turned on, the device will answer automatically when there is a
SIP phone connected. Alternatively, you can disable auto answer to use the device as a PBX loud ringer.
Device volume control: You can set the device volume level.
Edition v2.1
Aristel
Tabla de contenidos
