Ariens Deluxe 30 Manual de usuario

Quick Start Guide

Deluxe 30 Platinum (921018 s/n 75000 & up)

•Step 1: Assemble Handlebars

•Step 2: Install Discharge Chute

•Step 3: Install Chute Control Assembly

•Step 4: Install Discharge Chute Rod

•Step 5: Install Remote Deflector Control

•Step 6: Check Function of Dual Handle Interlock

•Step 7: Check Tire Pressure

•Step 8: Adjust Skid Shoes

•Step 9: Check Auger Gearcase Oil

•Step 10: Check Engine Crankcase Oil

•Step 11: Fill Engine Fuel Tank

•Step 12: Start Engine

•Step 13: Stop Engine

READ AND UNDERSTAND ALL INSTRUCTION, WARNING, AND DANGER LABELS.

IMPORTANT: READ OPERATOR’S MANUAL AND ENGINE MANUAL

THOROUGHLY AND FOLLOW THE IMPORTANT SAFE OPERATION PRACTICES

BEFORE OPERATING.

Step One: Assemble Handlebars

NOTE: The Ariens company has made changes to

packaging that affects this serial number range.

If the upper handlebars on your unit came already

attached please disregard the following five slides.

Not attached Attached

Step One: Assemble Handlebars

(Unfold Lower Handlebar)

IMPORTANT: Be sure to block wheels or secure unit so it does not

move during assembly.

1. Rotate lower handlebar out from unit so lower handlebar

mounting holes align with mounting holes on the unit frame.

2. Secure lower handlebar to unit using two 3/8 in x 3/4 in. hex

head serrated flange grade 5 bolts.

3. Tighten all four bolts to 25-42 lbf-ft (33,9-56,9 N∙m)

NOTE: This slide applies to

UNATTACHED handlebars ONLY

Step One: Assemble Handlebars

(Attach Upper Handlebar Assembly)

1. Attach upper handlebar assembly to lower handlebar using

two sets of the handlebar hardware. One set to attach each

side of the handlebars.

NOTE: DO NOT tighten hardware. Allow upper handlebar

assembly to hang from the lower handlebars for the next step.

NOTE: This slide applies to

UNATTACHED handlebars ONLY

Step One: Assemble Handlebars

(Attach Control Cables)

1. Hook Spring end of attachment control cable to the clutch

arm.

2. Hook spring end of the traction control cable to the cable

eyelet on back of frame.

NOTE: Make sure the cable remains in the groove of the pulley.

NOTE: This slide applies to

UNATTACHED handlebars ONLY

Step One: Assemble Handlebars

(Unfold Upper Handlebar)

Assembly)

1. Rotate handlebar into operating position.

NOTE: Be careful not to damage cable spring hooks when rotating

handlebar upward.

2. Install the remaining handlebar hardware attaching the upper

handlebar assembly to the lower handlebar.

3. Tighten all hardware.

4. Remove packaging around shift rod.

5. Rotate shift rod into place and tighten hardware.

6. Connect shift rod to speed selector arm and adjust as

specified. See Selector Adjustment in the Owners Manual.

7. Adjust attachment cable as specified. See Attachment

Clutch/Brake Adjustment in the Owners Manual.

8. Adjust the traction cable as specified. See Traction Drive

Clutch Adjustment in the Owners Manual.

NOTE: This slide applies to

UNATTACHED handlebars ONLY

Step One: Assemble Handlebars

(Connect Headlight Wire Harness)

NOTE: The headlight wire harness comes attached to the upper

handlebar assembly.

1. Route the wire harness along the interior of the right side

handlebar.

2. Connect to the engine electrical plug.

3. Press cable anchor into mounting hole in the frame near the

engine electrical plug.

4. Secure the wire harness to the handlebars using the cable

ties attached to the wire harness.

NOTE: This slide applies to

UNATTACHED handlebars ONLY

Step One:

Assemble Handlebar

1. Remove the lower and loosen the upper hardware on the

handlebar assembly.

2. Loosen the hardware on the shift rod.

3. Put the speed selector lever in the sixth forward position.

4. Rotate the handlebar into operating position.

NOTE: Be careful not to damage cable spring hooks when rotating

handlebar upward.

5. Install and tighten the hardware on the handlebar assembly

and shift rod.

NOTE: This slide applies to

ATTACHED handlebars ONLY

Step Two:

Install Discharge Chute

1. Grease underside of discharge chute ring (if not already

greased).

2. Remove mounting hardware from auger housing.

3. Install discharge chute over opening in the auger housing.

Finger tighten the mounting hardware removed above.

NOTE: Leave discharge chute pedestal loose to help install the

chute crank.

Step Three: Install Chute Control

Assembly

1. Remove the gear cover from top of chute pedestal.

2. Release the lock teeth on the gear assembly with your finger

and rotate the discharge chute so it points straight ahead.

NOTE: Make sure alignment markers are lined up when discharge

chute is pointing straight ahead.

Otros manuales para Deluxe 30

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Soplador de nieve de Ariens

Ariens

Ariens 921023 - Deluxe Track 28 Manual del propietario

Ariens

Ariens Sno-Tek 03883300A Manual del propietario

Ariens

Ariens 932045 - ST8524E Manual del propietario

Ariens

Ariens 921004 - ST924DLE Manual del propietario

Ariens

Ariens 924118 - 8524 Manual del propietario

Ariens

Ariens Professional Sno-Thro Series Manual de usuario

Ariens

Ariens SNO-THRO 932037 - 724 Manual del propietario

Ariens

Ariens SNO-THRO 924124 ST926DLE Manual del propietario

Ariens

Ariens Sno-Thro 938017 Manual del propietario

Ariens

Ariens SNO-THRO 924071 Manual de usuario

Ariens

Ariens 924000 Manual de usuario

Ariens

Ariens SNO-THRO Manual de usuario

Ariens

Ariens Sno-Thro 932100-824 Manual del propietario

Ariens

Ariens AMP 24 Sno-Thro Manual del propietario

Ariens

Ariens Professional Sno-Thro Series Manual de usuario

Ariens

Ariens Sno-Thro 10M4-04501 Manual de usuario

Ariens

Ariens SNO-THRO 924119 - 1028 Manual de usuario

Ariens

Ariens 926310-ST9526DLE Manual del propietario

Ariens

Ariens 924000 Manual de usuario

Ariens

Ariens 924119 Manual del propietario

Ariens

Ariens Sno-Thro Deluxe 28 Manual de usuario

Ariens

Ariens 926071 Manual de usuario

Ariens

Ariens Compact 24 LET Manual de usuario

Ariens

Ariens Sno-Thro ST11528LE Manual del propietario

Manuales populares de Soplador de nieve de otras marcas

Murray

Murray 624504X4A Manual de usuario

Blizzard

Blizzard POWER PLOW 8100PP Manual de usuario

Craftsman

Craftsman 486.24837 Manual de usuario

Yard-Man

Yard-Man E2B5 Manual de usuario

ST ST 526 A Manual de usuario

MTD

MTD 3AA Manual de usuario

Toro

Toro Power TRX 1428 OHXE Manual de usuario

Ryobi

Ryobi RYAC800 Manual de usuario

Poulan Pro

Poulan Pro 416829 Manual de usuario

Poulan Pro

Poulan Pro 437986 Manual de usuario

MTD

MTD 319-180-00 Manual de usuario

Brute

Brute 1695565 Manual de usuario

Egholm

Egholm City Ranger 2250 Manual de usuario

Poulan Pro

Poulan Pro 420915 Manual de usuario

GreenWorks

GreenWorks SNF402 Manual de usuario

LOFTNESS

LOFTNESS 601D1 Manual de usuario

LOFTNESS

LOFTNESS 1082I Manual de usuario

LOFTNESS

LOFTNESS 481EL Manual de usuario