Ares Gamma V2 Float Set Manual de usuario
QUICK-START GUIDE
For more great Ares products, just visit: www.Ares-RC.comFor more great Ares products, just visit: www.Ares-RC.com
Product specications are subject to change without notice.
Due to ongoing development, the actual product may vary from
images shown.
This product contains chemicals known to the State of California
to cause cancer, birth defects and other reproductive harm.
This product is not a toy! (14+) Recommended for ages 14 and
up. Adult supervision required for ages under 18 years old.
Contains small parts, keep out of reach of children 3 years of
age and younger.
Distributed in the
UK by:
J Perkins Distribution Ltd,
Lenham,
Kent, UK
ME17 2DL.
www.jperkins.com
Distributed in Australia by:
Model Engines (Aust.) Pty. Ltd.,
Unit 1, 158-168 Browns Road,
Noble Park,
Victoria,
3174,
Australia.
www.modelengines.com.au
Ph (03) 8793 5555
Distributed in the US by:
Firelands Customer Service/Product Support
1133 Libra Drive, Lincoln, NE 68512
www.relandsgroup.com
1-800-205-6773
customerservice@relandsgroup.com
Gamma V2 Float Set AZSA1640
Quick-Start Guide
MADE IN CHINA
Gamma V2
Float Set
QUICK-START GUIDE
For more great Ares products, just visit: www.Ares-RC.comFor more great Ares products, just visit: www.Ares-RC.com
1Remove the components from
the box and ensure you have the
following parts:
• Moulded oat set
• red/blue decal sheet
• 2x piano wire spacer bars
• 2x piano wire struts
• 4x strut saddle clamps
• 1x saddle clamp screw set
• 1x water rudder set
• 1x 1.5mm Allen key.
This Quick Start guide is written for the Gamma V2 Float Set.
A full instruction manual is available to download from www.ares-rc.com
2Unroll the self-adhesive sticker
sheet and carefully cut around the
edge of the trim stripes that match
your colour scheme. Apply the
stripe to the upper, outer edge of
each oat, starting at the front and
carefully peeling the backing paper
away as you work your way back.
3With the trim stripes correctly
applied each oat will be a handed
mirror image of the other.
4Slot one piano wire spacer bar
into position at the front of each
oat, noting that the bar locates
in the forward slot of the two. The
remaining spacer bar locates in the
front slot of the rear oat mount.
QUICK-START GUIDE
For more great Ares products, just visit: www.Ares-RC.comFor more great Ares products, just visit: www.Ares-RC.com
5Slot the piano wire spacer bar into
position at the front of each oat
noting that the strut locates in the
rearward slot behind the spacer
bar. Moving to the back of each
oat, slot the remaining strut into
position noting that it locates in the
rearward slot, behind the spacer
bar. Lock the struts and spacer
bars into position with the saddle
clamps and screws.
6Your oats are now assembled
and ready to be attached to the
fuselage.
7Glue the U-shape water rudder
mount over the base of the rudder
as shown, noting that it must be
located as far forward as possible
with the collet retainer positioned
at the front.
8Slot the rudder shaft into the collet
at the top of the water rudder and
tighten the grub screw to clamp it
in position.
9Slot the other end of the shaft
into the collet on the water rudder
mount and tighten the grub screw
to clamp it in position.
QUICK-START GUIDE
For more great Ares products, just visit: www.Ares-RC.comFor more great Ares products, just visit: www.Ares-RC.com
11 Slot the piano wire oat struts
into the mounts on the underside
of the fuselage and clamp them
in place using the four washer
head screws.
When tting the water rudder take
special care to ensure that it’s
perfectly aligned with the primary
air rudder. Adjust as necessary.
10
12 Your Gamma is now ready for a
swim. For the rst few ights pick
a relatively calm day when steering
and maneuvering for take-off will be
much easier. Always position your
Gamma dead into wind for take-off
and landing. At the start of your
take-off run hold in full up elevator
to raise the nose, then ease the
elevator off (as you would to raise the tail of a conventional tail-dragger)
as the Gamma gains speed and rises onto the step. Finally, gently re-apply
elevator to lift clear of the surface and enjoy ying off water.
Otros manuales de Juguete de Ares
Ares
Ares Gamma Pro V2 Manual de usuario
Ares
Ares Mini Gamma AZSA3150 Manual de usuario
Ares
Ares CRUSADER II Manual de usuario
Ares
Ares P-51D Mustang 350 Manual de usuario
Ares
Ares Tiger Month 75 Manual de usuario
Ares
Ares CHRONOS CX 75 Manual de usuario
Ares
Ares Nano-Micro Stick 75 Manual de usuario
Ares
Ares ultra-micro trainer 100 Manual de usuario
Ares
Ares Crusader II RTF Manual
Ares
Ares Taylorcraft 130 Manual de usuario
Ares
Ares sopwith pup Manual
Ares
Ares Ethos FPV Manual de usuario
Ares
Ares Nanos FP75 Manual de usuario
Ares
Ares Chronos FP 110 Manual de usuario
Ares
Ares Gamma 370 Pro Manual de usuario
Ares
Ares Chronos CX 100 Manual de usuario
Ares
Ares Decathlon Manual de usuario
Ares
Ares sopwith pup Manual de usuario
Ares
Ares AZSA1700 Manual de usuario
Ares
Ares Alara Manual
