Ardwolf A20 Manual de usuario
Product Introduction
1. Product Guide
2. Brief Introduction
Installation
Operation
1. Some Suggestions to Help Capturing the Fingerprint
2. Fingerprint Unlocking
3. Password Unlocking
4. Mechanical Key Unlocking
5. Add Users under Normal Mode
6. Add Master User under Normal Mode
7. Add Normal User under Security Mode
8. Delete Normal User under Normal Mode
9. Delete Master User under Security Mode
10. Delete Normal User under Security Mode
11. Passage Mode
12. Restore the Lock
13. Software – User Copy
14. Software – Lock Assistant
15. Frequently Asked Questions (FAQs) and Troubleshooting
----------------------------------------------1
--------------------------------------------------------1
------------------------------------------------------3
-----------------------------------------------------------4
-------------------------------------------------------------7
--------------------7
--------------------------------------------------8
--------------------------------------------------8
---------------------------------------------9
---------------------------------------10
---------------------------------11
-------------------------------12
------------------------------13
-----------------------------14
----------------------------15
------------------------------------------------------16
----------------------------------------------------17
-----------------------------------------------17
-------------------------------------------20
-------------22
Product Guide
1
1
2
1Keypad
2Fingerprint sensor
3Mechanical key hole
9V emergency power port
Battery area
“Add” button
“Delete” button
Mini USB port
Nixie tube
“Cancel” button
“Confirm” button
4
5
6
7
8
9
10
11
3
4
5
6
7
8
9
10
11
Product Guide
1
2
3
4
5
6
7
8
9
10
11
1
2
3
45
6
7
8
9
10
11
Outside Panel
Inside Panel
Latch
Screw for Latch
Strike Plate and Strike Box
Mechanical Key
Spindle
Screw M4x16
Screw M4x30
Connection Rod
Mounting Plate
2
1
2
There are 99 users available in the lock, which are divided by 2 levers:
b) Normal Level: This level of users only can unlock the lock, which cannot
set up the lock or modify the other users. The ID range is from “01” to “95”.
There are 2 modes available in the lock,which are “Security Mode”
and “Normal Mode”:
a) Master Level: Besides unlocking the lock, the master user can add
and delete other users. The ID range is from “96” to “99”.
Brief Introduction
b) Normal mode: when there is no master user registered in the lock, the lock is
under normal mode. In this case, anyone can set up the lock, like adding new users,
deleting users and so on.
a) Security Mode: when there is master user registered in the lock, the lock
will be changed to Security Mode automatically. If people want to set up the lock
like adding new users, deleting users, they have to wait for the authorization of
master users before operation.
It is suggested to keep the lock under Security Mode for a better security.
3Each ID only can be registered with one unlocking method: Fingerprint or Password.
The same fingerprint and same password cannot be registered in different ID.
4For password user, the password has to be 8 digits' combination between “1” to “8”.
5New lock under factory default (no users are registered in the lock) can be
unlocked by any fingerprint and password (password has to be 8 digits).
The ID will be shown as“00”.
Code Definition on Nixie Tube
There are 2 nixie tubes in the battery case after take out the battery cover, which
helps you to understand the lock states.
“AD”
“AL”
“FP”
“ID”
“NU”
the lock requires master user authorization.
delete all users in the lock (when the lock is under delete user operation)
delete user by inputting fingerprint or password directly (when the lock
is under delete user operation)
delete user by selecting ID (when the lock is under delete user operation)
the lock is under passage mode state.
3
Installation
Nine times out of ten, an error is the result of an improper installation
and/or wiring by the user. If you're not feeling particularly tech savvy,
let a professional put it in.
4
1. Place the template
on the door to make
the holes, and then drill
holes for installation.
2. Determine the backset for
your door.
3. Install the latch, and
fasten with screws, if a
70mm backset is required,
move the hole to the
right side.
4. Install the connection
rods on the front panel.
5. Insert the spindle into
the hole on the front panel.
There is an arrow symbol
on the hole, make sure the
arrow is facing down.
60mm 70mm
23
/4“23
/8“
Installation
5
60mm 70mm
23
/4“23
/8“
7. Install the base mounting
plate on the door, and fasten
with screws (M4x30)
The cable goes out from
the hold marked on the
picture.
6. Install the front panel on the door.
The cable goes on the top of the latch.
8. Connect the cable to the inside
panel, and the spindle goes into
the hole in the inside handle.
Installation
6
9. Install the inside panel on the
mounting plate, and fasten with
screw (M4x16)
10. Install the batteries
11. Replace the battery case
cover and fasten with screw.
Once finishing the installation, please try to unlock the lock to make sure
the installation is successful.
Operation
Some Suggestions to Help Capturing the Fingerprint
1
When placing the finger on the sensor, please make sure the “core” of fingerprint is
staying in the main area of sensor directly with a little bit pressure. Like the pictures
show as following:
The sensor may not capture the correct fingerprint image if you take the
following operations.
It is suggested to register the thumb, first finger, and middle finger
for better fingerprint images.
7
2Fingerprint Unlocking
Place the finger on the sensor, the lock will be activated automatically and
started to capture the fingerprint image for identification. Once the identification
is passed, the keypad shows “Green” light with sounds, then you can press down
the handle for unlocking.
“Green”
3Password Unlocking
Touch the keypad to activate the lock, then input the password (8 digits)
with pressing “ ” to finish. If the password is correct, the keypad shows
“Green” light with sounds, then you can press down the handle for
unlocking.
***
(8 digits) “Green”
When inputting a wrong password for 3 times, the lock will be locked for
5 minutes. During the 5 minutes, the lock cannot be activated and all
operations are not available. After that, the lock returns to normal state.
+
8
Tabla de contenidos
Otros manuales de Cerrar de Ardwolf
