Archgard NorthFire-DVT36E Manual de usuario

MODEL NORTHFIRE

DV36-E (Top Vent)

DIRECT VENTED BUILT-IN

GAS FIREPLACE

FOR USE WITH NATURAL GAS AND PROPANE

INSTALLATION AND OPERATING INSTRUCTIONS

FOR YOUR SAFETY

DO NOT store or use gasoline or any other flammable vapors or liquids in the vicinity

of this or any other appliance

IF YOU SMELL GAS:

- Do not try to light any appliance.

- Open windows.

- Do not touch electrical switches.

- Extinguish any open flame.

- Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier’s

instructions.

- If you cannot reach the gas supplier, call the fire department.

PLEASE READ INSTRUCTIONS CAREFULLY BEFORE INSTALLING AND

OPERATING THE APPLIANCE

WARNING: Improper installation, adjustment, alteration, service or maintenance voids

all the manufacturer’s warranties and may cause property damage, personal injury or

loss of life.

Installation and service must be performed by a qualified installer, service agency or the

gas supplier.

Installer, please leave this manual with the appliance owner for future reference.

WARNOCK HERSEY

CERTIFIED FOR CANADA AND USA

NOT FOR USE WITH SOLID FUEL

200-0055 22JAN02

fire-parts.com

CONTENTS

Introduction 2

General Information 3

Appliance Description and Dimensions 4

Installation Instructions 5 - 13

Operation Instructions 14 - 15

Maintenance 16

Trouble Shooting Instructions 17 - 18

Servicing 19 - 20

Important Information Form 21

Warranty 22

Parts and Accessories 23

Allowed Termination Location 24

Page

Manufactured by Archgard Industries Ltd, British Columbia, Canada.

Patents Pending

fire-parts.com

INTRODUCTION

Thank you for purchasing the NorthFire-DVT36E Direct Vent Built-in Gas Fireplace.

The NorthFire-DV36E is one of the most advanced gas fireplaces on the market. It is designed

using the latest technology and manufactured to the highest quality.

Some of the many features are:

∗ Small Size The NorthFire-DV36E is compact enough to fit into almost any size

room.

∗ Solid Construction The NorthFire-DV36E is constructed mainly of satin coated and

galvanized steel for long life and durability.

Please read the manual carefully prior to installation and operation of the appliance.

Proper installation, operation and maintenance of the appliance will provide you with

many years of enjoyment.

CAUTION

Due to high temperatures, the appliance should be located out of traffic and away from

furniture and draperies.

Children and adults should be alerted to the hazards of high surface temperature and

stay away to avoid burns or clothing ignition.

Young children should be carefully supervised when they are in the same room as the

appliance.

Clothing or other flammable material should not be placed on or near the appliance.

Any parts removed or opened for servicing of the appliance must be properly replaced

prior to operating the appliance.

The appliance must be inspected before use and at least annually by a qualified service

person. More frequent cleaning maybe required due to excessive lint from carpeting,

bedding material, etc. It is imperative that the control compartments, burners and

circulating air passageways for the appliance be kept clean.

fire-parts.com

GENERAL INFORMATION

This appliance is listed by Warnock Hersey for use in both the United States and Canada. It is

tested and certified to the following US and Canadian gas appliance standards.

- ANSI Z21.50-1996 / CGA 2.22-M96, Vented Gas Fireplace and

- CAN/CGA-2.17-M91, Gas-Fired Appliances for Use at High Altitudes.

Please contact Warnock Hersey or Archgard Industries Ltd., if you have any questions

regarding the certification of this appliance.

APPLIANCE CERTIFICATION

INSTALLATION CODES

This appliance must be installed by a qualified gas appliance installer.

The installation must conform with the local codes or, in the absence of local codes, with the

current National Fuel Gas Code, ANSI Z223.1/ NFPA 54, in the US or Installation Code,

CAN/CGA-B149, in Canada.

Electrical connections and grounding must conform with local code, or current National

Electrical code, ANSI/NFPA No. 70-1987, in the US and in Canada, the current Canadian

Electrical Code, CSA C22.1.

HIGH ALTITUDE INSTALLATION

When installing this appliance beyond 4500 ft. (1372 m) above sea level. The appliance must be

properly de-rated and installed according to local codes, in the absence of local codes, with the

current National Fuel Gas Code, ANSI Z223.1/ NFPA 54, in the US or Installation Code,

CAN/CGA-B149, in Canada.

Natural Gas (NG) Propane (LP)

Manifold Pressure 3.5 in. w.c. ( 0.9 kPa) 10.0 in. w.c. ( 2.5 kPa)

Min. Supply Pressure for Purpose

of Input Adjustment

4.5 in. w.c. (1.2 kPa) 11.0 in. w.c. (2.8 kPa)

Orifice Size #48 DMS ( 1.93 mm dia.) #56 DMS ( 1.18 mm dia.)

Nominal Input Rating 16,000 BTU/hr (5.8 kW) 16,000 BTU/hr ( 5.8 kW)

Altitude 0 - 4,500 ft. (0 - 1372 m) 0 - 4,500 ft. (0 - 1372 m)

Primary Air Opening 1/4 in. (6.4 mm) 1/2 in. (12.7 mm)

SPECIFICATIONS

fire-parts.com

APPLIANCE DESCRIPTION & DIMENSIONS

GAS VALVE

CONVECTION FAN

SPEED CONTROL

TOP LOUVERS

GLASS DOOR

APPLIANCE DIMENSIONS

FRONT VIEW

36 1/4”

23 1/2”

37 3/4”

TOP VIEW SIDE VIEW

FRONT VIEW

3 1/2”

* Except for the vent connector locations, the rear vented DVR36H and top vented DVT36H, have

the same physical dimensions.

5 1/4”

3/4”

fire-parts.com

ACross Corner

BFlush with Wall

CFlat on Wall Corner

DFlat on Wall

EIsland

FRoom Divider

15 ft Max.

INSTALLATION INSTRUCTIONS

PRECAUTIONS

•This appliance must be installed by a qualified gas installer and the installation conform to the

installation codes.

•Provide adequate clearance around air openings of the appliance. Never obstruct front openings.

•Provide adequate clearances for proper operation and servicing of the appliance.

•This appliance must be properly connected to a venting system.

LOCATING GAS FIREPLACE

This appliance must be installed in any location that is free of plumbing, electrical wiring and heating or

air conditioning ducts. Select a location that is accessible for venting. See APPENDIX A.

ALLOWABLE TERMINATION LOCATIONS.

VENT TERMINATION

1. See “ALLOWABLE TERMINATION LOCATIONS” diagram (page 24) to establish a suitable vent

termination location.

2. In heavy snowfall areas make sure vent termination is located where it can not be blocked by snow or

snow from snow removal equipment.

3. Locate vent termination away from plants, bushes or any other object on or near the vent termination

that will interfere or obstruct the air flow around it.

4. DO NOT recess vent termination into walls, sidings or planters.

5. Vent terminations located below 7ft from grade level or anywhere it can be a burn hazard to the public,

such as patios and balconies, must be protected with an Archgard approved termination cage.

6. Always ensure bottom of Vent Terminal is a minimum of 12” above grade.

*NOTE: Rear vented gas fireplace DVR36H can only be located in positions

A, B, C and D.

fire-parts.com

INSTALLATION INSTRUCTIONS Cont...

FRAMING DIMENSIONS

36 1/4”

16”

39 1/2”

28”

36 1/4”

56”

36 1/4”

*31”

16”

* If more rigidity is required. A stud may be added to the back of the top nailing flange

after the fireplace is installed.

TERMINATION

FRAMING

11”

10”

fire-parts.com

INSTALLATION INSTRUCTIONS Cont...

VENTING

The appliance will not function without being connected to a proper venting system.

This appliance may use 4” and 7” gas flex vents with NorthFire-DV36H listed vent components, or Simpson

Duravent 4 x 6 5/8 direct vent systems with Simpson Duravent Adaptor (SDA-1). 7” dia. rigid vent may

directly replace 7” dia. flex vent in all applications.

For best venting performance using gas flex vent, here are some general venting rules that we recommend:

1. Use only 4”and 7” diameter 2-ply certified gas flex vent in a co-axial configuration.

2. Maintain a minimum clearance of 1” to the sides and bottom and 2” to the top outside surface of the vent

pipe and combustible material.

3. Observe any local code restrictions, if any, regarding the installation of this type of gas appliance.

4. Observe the venting chart given in this manual.

5. Use a vent spacer between the inside and outside flex vents at every 3 ft intervals.

6. Never slope horizontal running vents downwards.

7. Maintain at least an upward slope of 1” for every 1 ft of horizontal run on the rear vented models.

8. Terminate the vent with a vent termination supplied by Archgard Industries Ltd.

9. Support horizontal running vents every 3 ft to prevent it from sagging.

10.Wall terminal must be installed a minimum of 12” above grade measured from bottom of terminal.

CLEARANCES TO COMBUSTIBLES

Combustible mantle allowed in shaded area. Mantle

extension may be increased 1” (25mm) for each

additional 1” (25mm) increase in clearance height.

6” (152 mm)

Minimum Height From Top Surround: 6”

Minimum Height From

Bottom of Appliance: 35”

BACK 0” to stand-offs

SIDES 0” to stand-offs

TOP 0” to stand-offs

BOTTOM 0”

ADJACENT SIDE WALL 1” to side of faceplate

MANTLE see diagram

VENT 1” to outside side and bottom surface,

2” to outside top surface.

fire-parts.com

INSTALLATION INSTRUCTIONS Cont...

RESTRICTOR PLACEMENT “FOR ABOVE 7 FOOT VERTICAL RISE VENTED

APPLICATIONS ONLY”

Vertical Venting between Seven Feet (7’) and Ten Feet (10’) requires

Restrictor Number 1 as per the Venting Chart on page 8.

Simpson Duravent Archgard System

Archgard System

In the Archgard system the restrictors are placed on the exhaust outlet on the appliance.

Simpson Duravent

With Simpson Duravent locate the restrictor in the exhaust section fitting into the formed lip.

Restrictor Placement

WARNING: These restrictors are only to be installed in the vent system if the vent exceeds 7’

in vertical height. *See below which restrictor is required. Installing them

under any other circumstances may cause hazardous venting conditions

and may result in personal injury, property damage or death.

NOTE: Vent restrictors are designed to reduce vertical stack action for above 7 feet (7’),

which will reduce the velocity of incoming combustion air and not adversely affect the standing

pilot or the flame of the appliance.

Vertical Venting between Ten Feet (10’) and up to a maximum

Twenty-five Feet (25’) requires Restrictor Number 2 as per the

Venting Chart on page 8.

fire-parts.com

INSTALLATION INSTRUCTIONS Cont...

VENTING Cont...

•Chart is for one 90° bend, with 1/4” vertical raise minimum per foot of horizontal length.

•For each additional 90° or two 45°, add 1ft of vertical height.

•Maximum two 90º bends, or equivalent.

•Minimum 2 ft straight length between bends.

Maintain a minimum of 1” clearance to combustibles on sides and bottom and 2” from top surface

of the vent.

The gas fireplace is designed and optimized for majority of the installations with short vents. With

taller vents the efficiency and flame characteristics will change. Therefore, an exhaust restrictor

plate is provided by the manufacturer to preserve as much of the original short vent performances as

possible on taller vent configurations.

NOTE: Maximum vent lengths subject to local codes.

VENTING CHART (FOR TOP VENTED APPLIANCES ONLY)

10 ft

36”

3 ft1 ft 15 ft

HORIZONTAL LENGTH

(from center of flue outlet to base of termination)

VERTICAL HEIGHT

(from bottom of appliance to center of termination)

7 ft

Venting in this area requires a vent restrictor plate #1.

5 ft 7 ft 9 ft 11 ft 13 ft

30”

Heater

Maximum Hori-

zontal run for

Rear Vent is 20”

from the back of

the unit to termi-

nation or 16” with

a 450 elbow.

VERTICAL VENTING (THROUGH THE ROOF) FOR ROOFTOP VENTED APPLIANCES

•Use only Simpson Duravent 4 x 6-5/8” direct vent systems and Simpson Duravent venting compo-

nents.

•Maximum vertical height of 25 feet.

•Vertical height of the vent system must have at least 3 ft or more per 900 elbow in the vent system.

•Vertical height of the vent system must also be increased 1 ft for every 2 ft of horizontal length

added to the vent system.

Example: A vertical venting system with a 900 elbow, a horizontal offset of 4 ft and another 900elbow.

Vertical height of the vent system must be 3ft + 2ft + 3ft = 8ft or higher to a maximum of 25 ft.

Vertical Venting between 10 ft and maximum 25 ft requires restrictor plate #2

fire-parts.com

Tabla de contenidos

Otros manuales de Chimenea de interior de Archgard

Archgard

Archgard 72-DVTE30P-2 Manual de usuario

Archgard

Archgard marquis AGDV-38D Manual de usuario

Archgard

Archgard NORTHFIRE 3400 Manual de usuario

Archgard

Archgard 22-DVIE22LN-1 Manual de usuario

Archgard

Archgard SALZBURG XL Manual de usuario

Archgard

Archgard 40-dvi40n Optima 40 - SB Manual de usuario

Archgard

Archgard 27-DVIE22N-2 Manual de usuario

Archgard

Archgard 36-DVIE40LN-1 Manual de usuario

Archgard

Archgard AGDVT-38 Manual de usuario

Archgard

Archgard OPTIMA 30 - 1 Manual del propietario

Archgard

Archgard DVR 36-H Manual del propietario

Archgard

Archgard Optima 20-1 Manual del propietario

Archgard

Archgard 45-DVFS28N-2 Manual del propietario

Archgard

Archgard CHALET 1600I Manual del propietario

Archgard

Archgard EURO 25 --1 Instrucciones de funcionamiento

Archgard

Archgard 25-BVI20N-3 Manual del propietario

Archgard

Archgard Kojin 50 Manual de usuario

Archgard

Archgard NORTHFIRE 3400 3400-DVTR20N-2 SN 8605 Manual de usuario

Archgard

Archgard CHALET 1800 Manual de usuario

Archgard

Archgard OPTIMA 30 - 1 Manual del propietario

Archgard

Archgard OPTIMA 22 Manual del propietario

Archgard

Archgard 72-DVTE30P-2-ERG Manual de usuario

Archgard

Archgard Harmonia 22 Manual de usuario

Archgard

Archgard Optima 3600O Guía

Manuales populares de Chimenea de interior de otras marcas

Brigantia

Brigantia 35-DVRS31N-2 Manual del propietario

Nordpeis

Nordpeis Bergen Manual de usuario

Superior

Superior BCT2536TMN Manual de usuario

Quadra-Fire

Quadra-Fire 5100I-GD-B Manual de usuario

Renaissance

Renaissance RUMFORD 1000 Manual de usuario

Lacunza

Lacunza IV-800 Manual de usuario

Baxi

Baxi 940 Instrucciones de uso

Dru

Dru Maestro 60/2 Tall RCH Manual de usuario

Diamond Fireglass

Diamond Fireglass SS-O22 Manual de usuario

HearthStone

HearthStone Windsor Bay 8830 Manual de programación

Napoleon

Napoleon ASCENT B42 Manual de usuario

Enviro

Enviro E33GI Manual de usuario

Smeg

Smeg L30 FABE Instrucciones de montaje

KEDDY

KEDDY K700 Manual de usuario

Godin

Godin 3451 Manual de usuario

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manual de usuario

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manual de usuario

Desa

Desa CCFPDFT Manual de operación