Aquverse 1PH Guía
1PH
Angle stop fitting (size depends on your water source, adaptable fitting
provided in water line kit)
Adjustable crescent wrench
Quick connect (2 sided coupler for poly line, provided in water line kit)
Drill with a 3/8 bit
Safety Glasses (Wear these at all times during installation)
To find the Aquverse warranty please go to www.aquverse.com
Poly Tubing (provided in water line kit)
Water filter
WARNING: This product is intended for indoor use only. Outside temperatures can cause damage to all systems. Please use only inside your home or office.
Phillips head screw driver
For any needed assistance please call 1-866-872-5722
****Warning do not plug water cooler in until water line is in place and dispensing water
through the faucets****
Aquverse Water Cooler Installation and Troubleshooting Instructions
WARNING: YOU MUST OBSERVE ALL LOCAL GOVERNING CODES AND ORDINANCES FOR INSTALLATION, OR THE
WARRANTY WILL BE VOIDED.
If you do not own the property where the unit will be installed, you need to contact the owner and obtain
approval before you install your cooler. If you are not comfortable with the installation procedure it is
recommended to have a professional licensed plumber complete the install for you.
WARNING: Do not use a saddle valve for installation or the warranty will be voided
Items You Need
Very sharp pair of scissors or a very sharp knife to cut tubing
Zip Ties (provided in water line kit)
First Steps
Determine where your cooler is going to be located and place it close to the determined area This drinking water system must be maintained in accordance with the manufacture's instructions
DO NOT PLUG IN (see instructions that are provided with filter)
A professional licensed plumber can perform the install or you can obtain the following items at your local hardware store: Maximum PSI = 10-125 psi/Capacity = 1500 gallons/Temperature = 35-100 F
Attaching Filter Re-attaching Front Cabinet
STEP 1
Secure the filter into the filter cup to prevent movement
STEP 1
STEP 2
Slide the top cover back into position
STEP 2
STEP 3
Re-attach the screws to secure the top cover
STEP 3
STEP 4
Cooler Set Up
Filter Specifications
Remove the screws located at the top of the back of the water cooler
Lift upwards at the back of the top cover and pull towards you
Lift the filter assembly up so that you can access the filter
Attach filter to filter head by pushing in, and turning to the right until it
stops
Locate Water Source Locate the cold water source
STEP 1
Make sure that the water source you will work with is connected to the
cold faucet on you sink by a water line hose.
STEP 1
Confirm Your Water Source Is Off
STEP 1
Drain the water from the faucet by turning on the hot and cold faucets
until no water is running
STEP 2
Turn the valve clockwise to shut of the water
A water source looks like this. It can be typically found underneath the
closest sink to were you would like to place your cooler
WARNING: YOU MUST OBSERVE ALL LOCAL GOVERNING CODES AND ORDINANCES
Installing Water Line Kit
STEP 1
Use the Water Line Kit clips to affix the tubing underneath the cabinet
alongside kick plate, or along wall to help keep out of sight.
STEP 6
STEP 2
Determine if you have excess waterline running from you water source ,
and if so cut the poly tubing to the correct length
STEP 7
STEP 3
Connect the two sided quick connect to the water line running out of
the bottom back corner of you water cooler
STEP 8
STEP 4
Connect the tubing into the two sided quick connect provide in the
waterline kit
STEP 9
STEP 5
Turn the water source back to the on position by turning
counterclockwise. Then let the water flow for 30 minutes while checking
for leaks
STEP 10
Unscrew the cold water line hose from the shut off valve (you will have a
few ounces of water remaining in the hose that will drip out)
Attach the angle stop to the shut off valve, if the fittings connect correctly
skip the next step
When finished with the above steps you should have tubing running from the angle stop that is attached to the water shut off valve(water source) to
the filter. Then tubing from the filter into the cooler.
Insert water line kit tubing into quick connect on angle stop
Run tubing from water source to cooler. If water source is located in a
cabinet then you will need to drill a small 3/8 inch hole into the front
corner to run the tubing underneath the cabinet
Wait a minimum of 30 minutes after you turn on the water source before plugging in filter
Attach the cold water line hose to the angle stop
Flushing the Filter
STEP 1
There is no danger in drinking the water with the carbon residue
discoloring the liquid, however for the freshest tasting and looking
water it is beneficial to flush the system.
NOTE
STEP 2
Begin Using Your Cooler
WARNING: YOU MUST OBSERVE ALL LOCAL GOVERNING CODES AND ORDINANCES
You must flush water through the filter to wash excess carbon out before
drinking (this is commonly referred to as priming the filter, and is
required)
To do this please flush two gallons (approximately 10 glasses of water)
through the cooler until the water is clear in color
You may begin to use the cooler immediately however it can take approximately 1 hour for the cold
tank, and hot tank to take effect and chill or heat the water in your cooler
What To Do If
Cooler Is Not Dispensing any Water
STEP 1
Check faucets to determine if water is blocked by any obstructions
STEP 3
STEP 2
Cooler is dispensing water but it is not chilled
STEP 1
If compressor is not functioning, call 1-866-872-5722 to receive
additional support
STEP 3
STEP 2
Turn the thermostat a 1/3 turn clockwise to resemble the picture shown
STEP 4
Cooler Troubleshooting
Only if your cooler has frozen, turn the cold water thermostat down by
turning a 1/4 turn counter clockwise.
Check that cold water thermostat is not turned to the off position (picture
shows thermostat in factory set "ON" position. The "OFF" position would
be a 1/3 turn counter clockwise
Confirm that cooler is not frozen by checking inside water tank, and
determining if water is frozen. If frozen unplug the water cooler and let
thaw, then proceed to the next step. If your cooler is not frozen skip
ahead to step 3
Determine whether the compressor is working by putting your ear close
to the top of the cooler (if you hear silence, the compressor is not
working, if you hear a humming noise the compressor is working)
Cooler is dispensing water but it is not Hot
STEP 1
Turn the cooler around so you are facing the back (wire caged portion)
of the cooler
STEP 4
STEP 2
Locate the hot tank through the back cage, and then locate the hot tank
reset button on the right side of the hot tank
STEP 5
STEP 3
Using a chopstick or screwdriver, depress the hot tank reset button
(water should be hot in 30 minutes time, see figure below which
pictures hole used to access hot tank reset button)
STEP 6
Water Is Leaking
STEP 1
If leaking is occurring from the nozzle of the faucets please contact
customer service at 1-866-872-5722 for replacement
STEP 3
STEP 2
If the leak is internal, please contact customer service at 1-866-872-5722
STEP 4
If hot tank switch is on then you will need to reset the hot tank (this can
be tripped to the off position much like a circuit breaker, if the cooler is
plugged in before water is filled into the tank)
Reset the hot tank by first unplugging the water cooler, then proceed to
the next steps
Identify the source of the leak (i.e. internal, faucets, or top)
Check the back of the cooler, and make sure the hot tank switch is in the
on position
If the faucets are the source of the leak, check to make sure the faucets
have been screwed on completely. If still leaking, drain the cooler of
water and remove the faucets, and make sure the gaskets around the
water spigots are in good condition
STEP 1
Fill the cold water tank with approximately four glasses of water
STEP 9
STEP 2
Drain this water through the cooler by opening the cold water faucet
STEP 10
STEP 3
Fill the cold water tank again with approximately four glasses of water
STEP 11
STEP 4
Drain this water through the cooler by opening the hot water faucet
(this may take more time then through the cold water faucet as done
previously)
STEP 12
STEP 5
Insert the cleaned baffle back into the cold water tank
STEP 13
STEP 6
Install the float valve back to its original placement as noted before
STEP 14
STEP 7
Install the to cover of cooler back in its original position
STEP 15
Cleaning Your Water Cooler
Turn the water source off
Unplug cooler
Drain water out of the hot faucet until the water reaches room
temperature (note that water is going to be hot when you begin draining)
Remove top cover of cooler
Remove the float valve from the top of the cold water tank (note the
position as you will need to re-install when cleaning is completed)
Remove the drain plug from the bottom of the cooler (water will drain out
of the cooler immediately, so you will need a bucket or receptacle to
catch the water
Remove the baffle from the cooler and wipe down with a clean dish
towel, and water (do not use bleach or any cleaners, you may use a small
amount of soap if desired)
STEP 8
STEP 1
Pull down gently on the filter until it is removed
STEP 5
STEP 2
Attach filter to filter head by pushing in, and turning to the right until it
stops
STEP 6
STEP 3
Secure the new filter into the filter cup to prevent movement
STEP 7
STEP 4
Slide the top cover back into position
Re-attach the screws to secure the top cover
STEP 8
For any needed assistance please call 1-866-872-5722
Lift the filter assembly up so that you can access the filter
TURN OFF WATER!
Remove the attached filter by turning to the left until it stops
Replacing Your Water Filter
Clean the cold tank with a clean dish towel, and water (do not use bleach
or any cleaners, you may use a small amount of soap if desired)
Remove the screw located at the top of the back of the water cooler
Lift upwards at the back of the top cover and pull towards you
Tabla de contenidos
Otros manuales de Dispensador de agua de Aquverse
