AquaLutio AL-1118 Manual de usuario
USER MANUAL 1
|
USER
MANUAL
Ruerse Osmosis
System
AL-1118
USER MANUAL
2|
e following tools may be necessary, depending on
each particular installation.
Electric Drill - 1/4" Drill Bit 6" Adjustable Wrench
Phillips Screw Driver
Teflon Tape
Plastic Tubing Cutter
»Operating pressure: 85psi maximum
»Feed water temperature: 40 – 100 degree F (4-37 degree C)
»Do not connect this unit to hot water source
»Install the RO in a sheltered environment, avoid exposure to
hot and cold weather or under direct sun light.
Operating Parameter
USER MANUAL 3
|
STORAGE
TANK
MACHINE
MAIN UNIT
FILTER
HOUSING
DRINKING
FAUCET
FILTER
CARTRIDGES
DRAIN
SADDLE
WATER
FEEDER
PLASTIC
TUBING
TANK
VALVE
HOUSING
WRENCHES
Components included with the RO system:
Make sure you have all these parts before starting installation.
Parts List
USER MANUAL
4|
STEP
1
Turn off the Cold Water Line
via the Cold Water Shutoff
Valve (CWSV) under the sink.
Open the kitchen faucet to
release pressure and make
sure water has stopped before
proceeding to the next step.
Get a towel or bucket to catch
water spill. Disconnect Kitchen
Faucet Connector (KFC) pipe
from CWSV.
1) Check Oring inside AFW
female end, and twist it
onto CWSV. Tighten it up
using wrench or pliers.
2) Twist KFC onto the male
end of AFW. Turn the
handle of AFW to cross
(OFF) position. Turn on
CWSV slowly, check and
x any leaks.
DO NOT OVERTIGHTEN AS IT MAY CRACK AND LEAK
Install Feed Water Adapter (AFW)
USER MANUAL 5
|
STEP
2
1) If your kitchen sink does not have an existing 1/2
inch hole, you will have to drill one. (Refer to: video
How to drill a Hole on Sink or Countertop). Wipe
clean and dry the area.
2) Slip the front plate on the faucet stem, followed by
the rubber washer. Insert the faucet stem into the
hole on countertop
3) Under the sink, slip on the back rubber washer,
tighten the nut with plastic wing.
4) Screw the tubing adapter on to the faucet stem.
Insert the tubing 1/2 inch deep into the Pushin tting.
Install Drinking Water Faucet
USER MANUAL
6|
STEP
3
1) Choose a spot on the drain pipe that is convenient
for installing the drain saddle and tubing. It is
recomended that you install the pipe horizontally to
minimize dripping sounds.
2) Drill a 1/4” hole on the drain pipe (Drill at point
approximately 6 inches above the trap);paste the
black sticky pad around the hole.
3) Install the back plate and tighten the two screws with
hex nuts while the tubing remains in the hole.
4) Tighten the nut securing the black drain line the
Drain Saddle by hand. Pull the tubing to check if it is
secure. Do not over tighten.
Install Drain Saddle
USER MANUAL 7
|
STEP
4
1) Stand the 3 housings upright. Make sure each
housing has a rubber O-ring in its groove.
2) Put the Essence sediment lter into the “1st stage”
housing on the right.
3) Put the Essence carbon lters into the “2nd and 3rd
stage” housing in the middle and left.
4) Starting from the 3rd stage housing on the left, hand
twist the housing onto the main system turning
counterclockwise, one by one, for all 3 housings.
Use the wrench provided to completely tighten the housing
starting from 1st-stage. Repeat this step for the 2nd stage
housing in the middle, and for the 3rd stage housing on
the left.
Install Filters
WRENCH
USER MANUAL
8|
STEP
5
The RO membrane is preserved in a sealed bag. Firmly
insert the membrane into the housing.
The smaller end with two black Orings should be
inserted rst, Push in until the back end is even with the
housing opening.
Check that the Oring is placed securely on the
membrane housing (cap does NOT have Oring).
Hand tighten and then using a small plastic housing
wrench tighten 1 /4 – 1 /2 turns, being careful not to
over tighten.
Install Reverse Osmosis Membrane
WRENCH
USER MANUAL 9
|
STEP
6
Apply Teon tape onto the threads of the tank nipple.
Screw the connector onto the tank making sure to avoid
cross threading. The connector only needs to be hand
tight (DO NOT OVER TIGHTEN) and should thread on
easily. Put the tank in place.
Tank Setup
CONNECTOR
Apply Tape
Do Not Touch
STEP
7
Place the system and the water storage tank in an area
under the sink so they are out of the way.
Unit Location
USER MANUAL
10 |
STEP
8
Cut the tubing in 4 pieces to make 4 connections. Make a
straight clean cut (recommended to use a cutter)
1) Locate the red plastic nut and connect to the water
supply, The side to the red plastic nut is a Quick-
Connect see page11, the other side AFW is not a
Quick-Connect its a compression tting. Unscrew
the nut and slip it onto 1/4" tubing. Insert the tubing
into the AFW (the T), push in rmly and then screw
and tighten the nut with your hands. Use wrench for
nal 1/4 turns.
2) Locate the black plastic nut and before connecting
to the drain cut the tubing end a 45 degree angle,
then Insert the tubing all the way into the 1/4” hole
on the drain pipe. (Quick-Connect see page 11)
3) Locate the yellow plastic nut and connect to the tank
(Quick-Connect see page 11)
4) Locate the blue plastic nut (Quick-Connect see
page 11) and connect to the faucet (see page 12)
System Hook Up
Tabla de contenidos
